Mazda CX 7. Manual — part 319
AIR BAG SYSTEM
08-10–13
08-10
SIDE AIR BAG SENSOR NO. 1 REMOVAL/INSTALLATION
id081000800600
Warning
• Handling the side air bag sensor improperly can accidentally operate (deploy) the air bag module,
which may seriously injure you. Read the air bag system service warnings and cautions before
handling the side air bag sensor. (See 08-10-3 AIR BAG SYSTEM SERVICE WARNINGS.) (See 08-
10-5 AIR BAG SYSTEM SERVICE CAUTIONS.)
1. Turn the ignition switch to the LOCK position.
2. Disconnect the negative battery cable and wait for 1 min or more.
3. Remove the following parts:
(1) Front scuff plate inner (See 09-17-19 FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
(2) Rear scuff plate inner (See 09-17-19 REAR SCUFF PLATE REMOVAL/INSTALLATION.)
(3) B-pillar lower trim (See 09-17-16 B-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
6. Turn the ignition switch to the ON position and
hold for 10 s or more.
7. Verify that the air bag system warning light
illuminates for approx. 6 s and goes out.
• If the air bag system warning light does not
operate normally, refer to the on-board
diagnostic system (air bag system) and perform inspection of the system.
Connector Removal Note
1. Disconnect the connector from the side air bag
sensor No.1 by pressing the connector tab and
pulling out the lock lever in the direction of the
arrow.
End Of Sie
1
Nut
2
Side air bag sensor No. 1
3
Connector
(See 08-10-13 Connector Removal Note.)
3
1
2
8.8—12.8 N·m
{89.8—130.5 kgf·cm,
77.8—113.2 in·lbf}
FRONT
acxuuw00000644
TAB
CONNECTOR
LOCK LEVER
acxuuw00000643
1871-1U-06B(08-10).fm 13 ページ 2006年3月15日 水曜日 午前11時36分
AIR BAG SYSTEM
08-10–14
SIDE AIR BAG SENSOR NO. 2 REMOVAL/INSTALLATION
id081000800700
Warning
• Handling the side air bag sensor improperly can accidentally operate (deploy) the air bag module,
which may seriously injure you. Read the air bag system service warnings and cautions before
handling the side air bag sensor. (See 08-10-3 AIR BAG SYSTEM SERVICE WARNINGS.) (See 08-
10-5 AIR BAG SYSTEM SERVICE CAUTIONS.)
1. Turn the ignition switch to the LOCK position.
2. Disconnect the negative battery cable and wait for 1 min or more.
3. Remove the following parts:
(1) Rear seat (See 09-13-7 REAR SEAT REMOVAL/INSTALLATION.)
(2) Rear scuff plate inner. (See 09-17-19 REAR SCUFF PLATE REMOVAL/INSTALLATION.)
(3) Sub trunk box (See 09-17-25 SUB TRUNK BOX REMOVAL/INSTALLATION.)
(4) Trunk end trim (See 09-17-24 TRUNK END TRIM REMOVAL/INSTALLATION.)
(5) Trunk side trim (See 09-17-24 TRUNK SIDE TRIM REMOVAL/INSTALLATION.)
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
6. Turn the ignition switch to the ON position and
hold for 10 s or more.
7. Verify that the air bag system warning light
illuminates for approx. 6 s and goes out.
• If the air bag system warning light does not
operate normally, refer to the on-board
diagnostic system (air bag system) and perform inspection of the system.
Connector Removal Note
1. Disconnect the connector from the side air bag
sensor No.2 by pressing the connector tab and
pulling out the lock lever in the direction of the
arrow.
End Of Sie
WM: CLOCK SPRING
1
Connector
(See08-10-14 Connector Removal Note.)
2
Side air bag sensor No. 2
3
Bolt
3
1
2
8.8—12.8 N·m
{89.8—130.5 kgf·cm,
77.8—113.2 in·lbf}
FRONT
acxuuw00000645
TAB
CONNECTOR
LOCK LEVER
acxuuw00000643
1871-1U-06B(08-10).fm 14 ページ 2006年3月15日 水曜日 午前11時36分
AIR BAG SYSTEM
08-10–15
08-10
CLOCK SPRING REMOVAL/INSTALLATION
id081000802000
1. Disconnect the negative battery cable and wait for 1 min or more.
2. Remove the following parts:
(1) Driver-side air bag module (See 08-10-6 DRIVER-SIDE AIR BAG MODULE REMOVAL/INSTALLATION.)
(2) Steering wheel (See 06-14-6 STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION.)
(3) Column cover (See 09-17-8 COLUMN COVER REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
5. Turn the ignition switch to the ON position.
6. Verify that the air bag system warning light
illuminates for approx. 6 s and goes out.
• If the air bag system warning light does not
operate normally, refer to the on-board
diagnostic system (air bag system) and
perform inspection of the system.
End Of Sie
CLOCK SPRING ADJUSTMENT
id081000802100
Note
• The adjustment procedure is also specified on the caution label of the clock spring.
1. Set the front tires straight-ahead.
Caution
• The clock spring will break if over-wound. Do not forcibly turn the clock spring.
2. Turn the clock spring clockwise until it stops.
3. From the stopped position, turn the clock spring
counterclockwise 2 3/4 turns.
1
Connector
2
Screw
3
Clock spring
3
1
2
acxuuw00001390
acxuuw00001596
acxuuw00001597
1871-1U-06B(08-10).fm 15 ページ 2006年3月15日 水曜日 午前11時36分
AIR BAG SYSTEM
08-10–16
4. Align the marks.
End Of Sie
CLOCK SPRING INSPECTION
id081000802200
1. Verify that the continuity is as indicated in the table.
• If not as indicated in the table, replace the clock spring.
Note
• When the vehicle-side connector for the clock spring is disconnected, terminals 1A, 1B, 1C and 1D are
shorted to prevent unexpected operation (deployment) of the air bag module.
ALIGNMENT MARKS
acxuuw00001598
1A
1B
1C
1D 2A
2B
2C 2D 2E
2H 3A
3B 4A
4B
5A
5B
5C 5D
5E
2G
5G 5H
Test
condi-
tion
Under
any
condi-
tion
Terminal
: Continuity
acxuuw00001599
1871-1U-06B(08-10).fm 16 ページ 2006年3月15日 水曜日 午前11時36分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст