Mazda CX 7. Manual — part 434
INSTRUMENTATION/DRIVER INFO.
09-22–5
09-22
INSTRUMENT CLUSTER INPUT/OUTPUT CHECK MODE
id092200801700
Note
• In this mode, it is possible to verify the items in the following chart.
Check Code Table
Note
• Check codes which are not listed may be indicated, but they cannot be inspected.
• The check codes are displayed in numerical order. (While performing the inspection, if you want to inspect
a check code with a number smaller than the code number you are currently inspecting, terminate the
check mode then repeat the inspection from the beginning.)
• If a speed signal is input to the instrument cluster (the wheels are rotated), the input/output check mode
will be cancelled.
• The check codes can be fast-forwarded by pushing and holding the odometer/tripmeter switch for 1 s or
more.
Check code
Check item
Related items
08
TNS relay
• Lights-on reminder warning alarm
• Each illumination light
12
Speedometer
Speedometer
13
Tachometer
Tachometer
14
Buzzer
Buzzer
16
Fuel-level warning light
Fuel-level warning light
22
Fuel gauge sender unit
Fuel gauge
23
Fuel gauge
Fuel gauge
25
Water temperature gauge
Water temperature gauge
26
• Odometer/tripmeter (LCD)
• Warning and indicator light
• Odometer/tripmeter (LCD)
• Warning and indicator light
55
Panel light control switch (dimmer switch)
Panel light control switch (dimmer switch)
57
Panel light control
Illumination light bulb
59
• CAN system
• Fuel gauge sender unit
• CAN system
• Fuel system
1871-1U-06B(09-22).fm 5 ページ 2006年3月15日 水曜日 午後12時56分
INSTRUMENTATION/DRIVER INFO.
09-22–6
1. Press and hold the odometer/tripmeter switch, and turn the ignition switch to the ON position.
2. Continue holding the odometer/tripmeter switch for approx. 5 s. ( is displayed on LCD.)
3. Release the odometer/tripmeter switch within 3 s after is displayed.
Disconnect the connectors of the following parts and verify continuity
of the wiring harness.
Instrument cluster—fuel gauge sender unit
Is there continuity?
Disconnect the negative battery cable.
Connect the instrument
cluster connector.
Start
Repair the wiring harness.
If a malfunction occurs after repairing
the wiring harness, connect the instrument
cluster connector.
Connect the SST (Fuel and thermometer
checker) to the instrument cluster.
Connect the negative battery cable.
Turn the ignition switch to the LOCK position.
Does the odometer/tripmeter indicate first check code?
Push the odometer/tripmeter switch to select a check code.
Perform the "Check Code Inspection".
Is there any malfunction?
Are there any check codes to inspect?
Turn the ignition switch to the LOCK position.
Disconnect the negative battery cable.
Disconnect the SST (Fuel and thermometer checker) and connect the fuel gauge sender
unit connector, if necessary.
Connect the negative battery cable.
End
Except
check
code 22
Inspection
preparation
Inspection
procedure
Ending
procedure of
instrument
cluster
input/output
check mode
Check code 22
Yes
Yes
No
Yes
No
No
Yes
No
Repair or replace parts.
Perform the following procedure:
acxuuw00002169
1871-1U-06B(09-22).fm 6 ページ 2006年3月15日 水曜日 午後12時56分
INSTRUMENTATION/DRIVER INFO.
09-22–7
09-22
Checking Order
Note
• When inspecting more than two check codes, begin with the code with the highest ranking.
Check Code Inspection
Check code 08
Check code 12
Check code 13
Priority order of inspection
Check code
1
22
2
08, 12, 13, 14, 16, 23, 25, 26, 55, 57, 59
Check code 08
TNS relay ON/OFF signal
STEP
INSPECTION
CONDITION
DISPLAY
ACTION
1
Turn the headlight switch
to the TNS position. (TNS
relay ON)
Go to the next step.
Verify that the voltage of instrument cluster terminal 2I is B+.
• If the voltage is as specified, replace the instrument
cluster.
• If the voltage is not as specified, inspect the following
parts:
— TNS relay
— Wiring harness (Battery— TNS relay— instrument
cluster)
2
Turn the headlight switch
off. (TNS relay OFF)
Verify that the voltage of the instrument cluster terminal 2I is
1.0 V or less.
• If the voltage is as specified, replace the instrument
cluster.
• If the voltage is not as specified, inspect the following
parts:
— TNS relay
— Wiring harness (TNS relay— instrument cluster)
Input signal to the instrument cluster is normal.
Check code 12
Speedometer display signal
INSPECTION CONDITION
DISPLAY
ACTION
After selecting check code 12, wait for
approx. 2 s.
The speedometer needle
moves full scale then returns
to approx. 60 km/h.
The speedometer is normal.
Except above
Replace the instrument
cluster.
—
Check code 13
Tachometer operation signal
INSPECTION CONDITION
DISPLAY
ACTION
After selecting check code 13, wait for
approx. 2 s.
The tachometer needle
moves full scale then returns
to approx. 3,000 rpm.
The tachometer is normal.
Except above
Replace the instrument
cluster.
—
1871-1U-06B(09-22).fm 7 ページ 2006年3月15日 水曜日 午後12時56分
INSTRUMENTATION/DRIVER INFO.
09-22–8
Check code 14
Check code 16
Check code 22
Check code 14
Buzzer operation signal
INSPECTION CONDITION
DISPLAY
ACTION
After selecting check code 14, wait
approx. 2 s.
The buzzer sounds.
The buzzer is normal.
The buzzer does not sound.
Replace the instrument
cluster.
Check code 16
Fuel-level warning light flashing signal
INSPECTION CONDITION
DISPLAY
ACTION
After selecting check code 16, wait
approx. 2 s.
Fuel-level warning light
flashes three times.
The fuel-level warning light is
normal.
Except above
Replace the instrument
cluster.
Check code 22
Fuel level signal
STEP
INSPECTION
CONDITION
DISPLAY
ACTION
1
Select check code 22 with
the fuel gauge sender unit
connector disconnected.
Go to the next step.
Except above
Go to the Step 6.
2
Connect terminals 2U and
2W of the instrument
cluster.
Go to the next step.
Except above
Go to the Step 6.
3
Using the SST (Fuel and
thermometer checker) or
resistor, input 20 ohms
between instrument cluster
terminals 2U and 2W.
Go to the next step.
Except above
Go to the Step 6.
4
Using the SST (Fuel and
thermometer checker) or
resistor, input 60 ohms
between instrument cluster
terminals 2U and 2W.
Go to the next step.
Except above
Go to the Step 6.
5
Using the SST (Fuel and
thermometer checker) or
resistor, input 100 ohms
between instrument cluster
terminals 2U and 2W.
Inspect the fuel gauge sender unit.
Except above
Go to the next step.
(FLASHING)
1871-1U-06B(09-22).fm 8 ページ 2006年3月15日 水曜日 午後12時56分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст