Mazda CX 7. Manual — part 181
DRIVE SHAFT
03-13–11
03-13
Dust Seal Assembly Note
1. Apply grease to the new dust seal lip.
2. Install the new dust seal using a press and the
SSTs.
Substitution SST
• 49 G028 203
Outer diameter: 64 mm {2.5 in} or more
Inner diameter: 57.6— 59.0 mm {2.27— 2.32
in}
Inner depth: 38.5 mm {1.52 in} or more
End Of Sie
WM: DRIVE SHAFT
FRONT DRIVE SHAFT PRE-INSPECTION
id031300800200
1. Inspect the dust boot on the drive shaft for cracks,
damage, leaking grease, and looseness in the
boot band.
2. Inspect the drive shaft for bends, cracks, and
wear in the joint or splines.
• Repair or replace the drive shaft or boot/band
as necessary.
End Of Sie
49 G028 203
acxuuw00001358
A6E0313W033
1871-1U-06B(03-13).fm 11 ページ 2006年3月15日 水曜日 午前11時6分
DRIVE SHAFT
03-13–12
FRONT DRIVE SHAFT REMOVAL/INSTALLATION
id031300800300
Caution
• Performing the following procedures without first removing the ABS wheel-speed sensor may
possibly cause an open circuit in the harness if it is pulled by mistake. Before performing the
following procedures, remove the ABS wheel-speed sensor (axle side) and fix it to an appropriate
place where the sensor will not be pulled by mistake while the vehicle is being serviced.
1. Remove the side cover and under cover.
2. Remove the front ABS wheel-speed sensor. (See 04-15-11 FRONT ABS WHEEL-SPEED SENSOR
REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
.
A
A
5
3
6
1
2
5
6
SST
R
R
R
R
47.0—59.0
{4.80—6.01,
34.7—43.5}
43.1—58.8
{4.40—5.99,
31.8—43.3}
42.3—60.1
{4.32—6.12,
31.2—44.3}
235.2—274.4
{23.99—27.98,
173.5—202.3}
N·m {kgf·m, ft·lbf}
4
acxuuw00001222
1
Locknut
(See 03-13-13 Locknut Removal Note.)
(See 03-13-14 Locknut Installation Note.)
2
Tie-rod end ball joint
(See 02-13-10 FRONT CROSSMEMBER
REMOVAL/INSTALLATION.)
3
Front stabilizer control link (lower side)
4
Front lower arm ball joint
5
Front drive shaft
(See 03-13-13 Front Drive Shaft Removal Note.)
(See 03-13-14 Front Drive Shaft Installation Note.)
6
Clip
(See 03-13-13 Clip Installation Note.)
1871-1U-06B(03-13).fm 12 ページ 2006年3月15日 水曜日 午前11時6分
DRIVE SHAFT
03-13–13
03-13
Locknut Removal Note
1. Lock the hub by applying the brakes.
2. Knock the crimped portion of the locknut outward
using a small chisel and a hammer.
3. Remove the locknut.
Front Drive Shaft Removal Note
1. Install a spare nut onto the drive shaft so that the nut is flush with the end of the drive shaft.
2. Tap the nut with a copper hammer to loosen the
drive shaft from the front wheel hub.
3. Separate the drive shaft from the wheel hub.
Caution
• The sharp edges of the drive shaft can
slice or puncture the oil seal. Be careful
when removing the drive shaft from the
transaxle.
4. Separate the left side drive shaft from the
transaxle by prying with a bar inserted between
the outer ring and the transaxle, as shown in the
figure.
5. Separate the right side drive shaft from the joint
shaft by tapping on a bar inserted between them.
Clip Installation Note
1. Install a new clip onto the drive shaft with the opening facing upward. Ensure that the diameter of the clip does
not exceed the specification on installation.
acxuuw00001114
acxuuw00001115
acxuuw00001223
acxuuw00001224
1871-1U-06B(03-13).fm 13 ページ 2006年3月15日 水曜日 午前11時6分
DRIVE SHAFT
03-13–14
2. After installation, measure the outer diameter. If it
exceeds the specification, repeat Steps 1— 2
using a new clip.
Clip outer diameter specification
LH: 33.5 mm {1.32 in}
RH (joint shaft): 34.0 mm {1.34 in}
Front Drive Shaft Installation Note
Caution
• The sharp edges of the drive shaft can slice or puncture the oil seal. Be careful when installing the
drive shaft to the transaxle.
• The oil seals are damaged easily if this
procedure is not done correctly.
Left side
1. Insert the drive shaft into the wheel hub.
2. Apply transaxle oil to the oil seal lip.
3. Push the drive shaft into the transaxle.
4. After installation, pull the transaxle side outer ring forward to confirm that the drive shaft is securely held by the
clip.
Right side
1. Insert the drive shaft into the wheel hub.
2. Insert the drive shaft into the joint shaft.
3. After installation, pull the transaxle side outer ring forward to confirm that the drive shaft is securely held by the
clip.
Locknut Installation Note
1. Install a new locknut and stake it as shown.
End Of Sie
OUTER
DIAMETER
OPENING
CLIP
acxuuw00001225
acxuuw00001226
0.5 mm {0.02 in} OR MORE
acxuuw00001128
1871-1U-06B(03-13).fm 14 ページ 2006年3月15日 水曜日 午前11時6分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст