Mazda CX 7. Manual — part 206
SYMPTOM TROUBLESHOOTING
04-03–9
04-03
NO.2 ANY OF THE FOLLOWING LIGHTS REMAIN ON: (ABS WARNING LIGHT, BRAKE SYSTEM WARNING
LIGHT, DSC INDICATOR LIGHT AND/OR TCS OFF LIGHT)
id040300803700
Diagnostic procedure
End Of Sie
2
Any of the following lights remain on: (ABS warning light, BRAKE system warning light, DSC
indicator light and/or TCS OFF light)
[TROUBLESHOOTING HINTS]
• Brake fluid amount is low
• Parking brake does not release
• No connection at DSC HU/CM connector
(When DSC HU/CM connector is disconnected, ABS warning light and BRAKE system warning light illuminate)
• DSC HU/CM detected malfunction (Input and output device malfunction)
• DSC HU/CM detects low voltage in power supply
• DSC HU/CM ground malfunction
(When DSC HU/CM ground is not securely connected, ABS warning light and BRAKE system warning light
illuminate but diagnostic trouble code does not displayed)
• DSC HU/CM does not operate (DSC HU/CM malfunction)
STEP
INSPECTION
ACTION
1
INSPECT BRAKE FLUID AMOUNT AND
VERIFY THAT PARKING BRAKE RELEASES
• Is the brake fluid amount normal?
• Is the parking brake lever released?
Yes
Go to the next step.
No
Add brake fluid or release parking brake lever.
2
INSPECT DTCS IN INSTRUMENT CLUSTER
• Inspect the DTC for the instrument cluster
ON-BOARD DIAGNOSTIC SYSTEM.
• Has DTC U2064 been recorded in memory?
Yes
Go to the next step.
No
Inspect the instrument cluster.
(See 09-22-3 INSTRUMENT CLUSTER INSPECTION.)
3
INSPECT DTCS IN DSC HU/CM
• Inspect the DTC for the DSC ON-BOARD
DIAGNOSTIC SYSTEM.
• Have DTCs been stored in memory?
Yes
Perform inspection using appropriate DTC.
(See 04-02-3 ON-BOARD DIAGNOSIS.)
No
Go to the next step.
4
INSPECT WHETHER MALFUNCTION IS IN
CONTROL MODULE CONNECTOR,
TERMINAL OR OTHER
• Do the ABS warning light and BRAKE
system warning light go out after 4 s when
the ignition switch is turned to the ON
position?
Yes
Temporary poor connection in control module connector.
Inspect DSC HU/CM connector, then go to Step 7.
Inspect DSC HU/CM connector terminal, then go to Step 8.
No
Go to the next step.
5
INSPECT BATTERY
• Is the battery voltage normal?
Yes
Go to the next step.
No
Inspect the battery and charging system.
(See 01-17-2 BATTERY INSPECTION[L3 WITH TC].)
(See 01-17-6 GENERATOR INSPECTION[L3 WITH TC].)
6
INSPECT CHARGING SYSTEM
• Is the battery voltage normal with electrical
load (A/C, headlight, etc.) on and engine
idling?
Yes
Go to the next step.
No
Inspect the charging system (drive belt tension, generator,
etc.).
(See 01-17-6 GENERATOR INSPECTION[L3 WITH TC].)
7
VERIFY THAT DSC HU/CM CONNECTOR IS
CONNECTED
• Is the DSC HU/CM securely connected?
Yes
Go to the next step.
No
Connect the DSC HU/CM connector securely, then go to the
next step.
8
VERIFY THAT DSC HU/CM CONNECTOR
TERMINAL OR RELATED CONNECTOR
TERMINALS ARE CONNECTED
• Are the DSC HU/CM connector terminal or
instrument cluster connector terminal etc.
related connector terminals securely
connected?
Yes
Replace the DSC HU/CM.
(See 04-15-6 DSC HU/CM REMOVAL/INSTALLATION.)
No
Securely connect the DSC HU/CM connector terminal and
related connector terminals.
1871-1U-06B(04-03).fm 9 ページ 2006年3月15日 水曜日 午前11時12分
SYMPTOM TROUBLESHOOTING
04-03–10
NO.3 THERE IS A MALFUNCTION IN THE SYSTEM EVEN THOUGH ABS WARNING LIGHT, BRAKE SYSTEM
WARNING LIGHT, DSC INDICATOR LIGHT AND TCS OFF LIGHT DO NOT ILLUMINATE
id040300803800
Diagnostic procedure
End Of Sie
NO.4 ABS OR TCS
*1
OPERATES FREQUENTLY/TCS DOES NOT WORK CORRECTLY
*1
: DSC SYSTEM
FUNCTION CONTAINS TRACTION CONTROL FUNCTION, DSC INDICATOR LIGHT GOES ON AND OFF
WHILE DSC IS OPERATING
id040300803400
Diagnostic procedure
End Of Sie
3
There is a malfunction in the system even though the ABS warning light, BRAKE system warning
light, DSC indicator light and TCS OFF light do not illuminate.
[TROUBLESHOOTING HINTS]
• There is a mechanical malfunction in system
STEP
INSPECTION
ACTION
1
INSPECT DSC HU/CM FOR DTCs
• Inspect the DTC for the DSC ON-BOARD
DIAGNOSTIC SYSTEM.
• Have DTCs been stored in memory?
Yes
Perform the applicable DTC inspection.
(See 04-02-3 ON-BOARD DIAGNOSIS.)
No
Go to the next step.
2
INSPECT DSC SYSTEM
• Perform DSC system inspection.
(See 04-15-4 DSC SYSTEM INSPECTION.)
• Is the system normal?
Yes
Inspect the conventional brake system.
No
Repair or replace any malfunctioning part.
4
ABS or TCS (*1) operates frequently./TCS does not work correctly.
(*1): DSC system function contains traction control function; DSC indicator light goes on and off
while DSC is operating.
[TROUBLESHOOTING HINTS]
• There is a difference in size or air pressure between the front and rear tires
• Incorrect ABS wheel-speed signal is input to DSC HU/CM
• There is a malfunction in the engine control system (TCS malfunction)
• Tire problem (low or high air pressure, excessive wear, different grip level by four wheels)
STEP
INSPECTION
ACTION
1
INSPECT DTCS IN DSC HU/CM
• Inspect the DTC for the DSC ON-BOARD
DIAGNOSTIC SYSTEM.
• Have DTCs been stored in memory?
Yes
Perform the applicable DTC inspection.
(See 04-02-3 ON-BOARD DIAGNOSIS.)
No
Go to the next step.
2
INSPECT TIRE SIZE AND AIR PRESSURE
• Inspect the tire size and the air pressure.
• Are size and air pressure as specified?
Yes
Go to the next step.
No
Replace with specified tires and adjust tire air pressure.
3
INSPECT ABS WHEEL-SPEED SENSOR
OUTPUT VALUE
• Inspect the output value from the ABS
wheel-speed sensor.
(See 04-15-12 FRONT ABS WHEEL-SPEED
SENSOR INSPECTION.)
(See 04-15-14 REAR ABS WHEEL-SPEED
SENSOR INSPECTION[2WD].)
(See 04-15-14 REAR ABS WHEEL-SPEED
SENSOR INSPECTION[AWD].)
• Is the output value normal?
Yes
Go to the next step.
No
• ABS wheel-speed sensor installation inspection:
Inspect the sensor for looseness and verify that it is
securely installed.
• Sensor rotor installation inspection:
Inspect the sensor rotor for poor installation and
chipping of sensor rotor teeth. (If sensor rotor is installed
poorly, it may cause output of abnormal wave form at
high speed.)
4
VERIFY THAT TIRE CONDITION
• Verify tire condition for following:
— Wear
— Grip level (different by four wheels)
• Are tires condition okay?
Yes
Find malfunctioning part according to "INTERMITTENT
CONCERN TROUBLESHOOTING".
No
Adjust, repair or replace tire.
1871-1U-06B(04-03).fm 10 ページ 2006年3月15日 水曜日 午前11時12分
SYMPTOM TROUBLESHOOTING
04-03–11
NO.5 DSC
*2
OPERATES FREQUENTLY/DSC DOES NOT WORK CORRECTLY
*2
: DSC INDICATOR LIGHT
GOES ON AND OFF WHILE DSC IS OPERATING
id040300803500
Diagnostic procedure
End Of Sie
5
DSC (*2) operates frequently. /DSC does not work correctly.
(*2): DSC indicator light goes on and off while DSC is operating.
[TROUBLESHOOTING HINTS]
• DSC HU/CM detected malfunction (input and output device malfunction)
• Poor installation of yaw rate sensor, lateral-G sensor and/or steering angle sensor
(If any of the above sensors are poorly installed, DSC may operate intermittently)
• When replacing the DSC HU/CM, combined sensor or steering angle sensor, initialization is not performed.
(If initialization is not performed correctly, DSC may not work correctly)
STEP
INSPECTION
ACTION
1
INSPECT DSC HU/CM FOR DTCs
• Inspect the DTC for the DSC ON-BOARD
DIAGNOSTIC SYSTEM.
• Have DTCs been recorded in memory?
Yes
Perform the applicable DTC inspection.
(See 04-02-3 ON-BOARD DIAGNOSIS.)
No
Go to the next step.
2
VERIFY THAT EACH SENSOR IS INSTALLED
• Are the combined sensor and steering angle
sensor securely installed?
Yes
Go to the next step.
No
Install sensor securely.
*3
VERIFY THAT EACH SENSOR IS INITIALIZED
• Was initialization performed after
replacement of the DSC HU/CM, combined
sensor or steering angle sensor?
Yes
Go to the next step.
No
Perform initialization procedure.
(See 04-15-17 COMBINED SENSOR INITIALIZATION
PROCEDURE.)
(See 09-40-8 STEERING ANGLE SENSOR
INITIALIZATION PROCEDURE.)
4
VERIFY THAT TIRE CONDITION
• Verify tire condition for following:
— Air pressure
— Wear
— Grip level (different by four wheels)
• Are tires condition okay?
Yes
Find malfunctioning part according to "INTERMITTENT
CONCERN TROUBLESHOOTING".
No
Adjust, repair or replace tire.
1871-1U-06B(04-03).fm 11 ページ 2006年3月15日 水曜日 午前11時12分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст