Mazda CX 7. Manual — part 161
WHEEL AND TIRES
02-12–5
02-12
.
Valve Core Removal Note
1. Remove the valve core of the wheel unit, and bleed the air from the tire.
Wheel Unit Removal Note
1. Push the tire valve completely into the tire.
Caution
• Breaking the tire bead with the wheel unit installed normally could damage the unit. Be sure to
always push the wheel unit so that it is completely inside the tire to prevent any damage.
2. Position the shoe (bead breaker) of the tire changer 10— 20 mm {0.40— 0.78 in} from the outer edge of the
wheel, and break both tire beads.
3. Remove the bead from one side of the wheel.
4. Remove the wheel unit.
R
R
R
R
7.5—8.5
{77—86, 67—75}
1
2
3
4
N·m {kgf·cm, in·lbf}
6
5
acxuuw00001040
1
Valve cap
2
Valve core
(See 02-12-5 Valve Core Removal Note.)
3
Valve nut and washer
4
Wheel unit
(See 02-12-5 Wheel Unit Removal Note.)
(See 02-12-6 Wheel Unit Installation Note.)
5
Seal washer
6
Seal
1871-1U-06B(02-12).fm 5 ページ 2006年3月15日 水曜日 午前10時59分
WHEEL AND TIRES
02-12–6
Wheel Unit Installation Note
1. Insert the wheel unit valve into the valve hole so
that the polyurethane foam side faces the rim.
Note
• Maintain the wheel unit in contact with the
rim, then start manually to screw the valve
nut for a few turns.
2. Install the nut from the outer side of the wheel.
3. Tighten the valve nut slowly (15 rpm max.) to 8.0
N·m {82 kgf·cm, 71 in·lbf} in one rotation.
Caution
• Do not retighten the valve nut after the
initial operation.
4. Set the tire changer so that it is 45
° away (point A)
from the valve hole.
Caution
• Do not position the tire changer near the
tire valve to avoid any damage to the
wheel unit.
5. Fill the tire with air and verify the valve nut
tightening torque.
Caution
• To prevent damage to the valve area of
the wheel unit or charging loss during air
pressure adjustment, use a type B tool
with a round end as shown in the figure,
not a type A tool.
End Of Sie
WHEEL UNIT
VALVE HOLE
acxuuw00001041
POINT A
POINT A
VALVE
VALVE
45
°
45
°
TIRE ROTATION
DIRECTION
TIRE ROTATION DIRECTION
THE ARM OF
THE TIRE
CHANGER
acxuuw00001042
TYPE A
TYPE B
acxuuw00001043
1871-1U-06B(02-12).fm 6 ページ 2006年3月15日 水曜日 午前10時59分
FRONT SUSPENSION
02-13–1
02-13
2007 Mazda CX-7 Workshop Manual (1871–1U–06B)
Revised 9/2006 (Ref. No. R115/06)
02-13
FRONT SUSPENSION
FRONT SUSPENSION
LOCATION INDEX. . . . . . . . . . . . . . . . . 02-13–2
FRONT SHOCK ABSORBER
AND SPRING
REMOVAL/INSTALLATION . . . . . . . . . 02-13–3
Front Shock Absorber and
Coil Spring Installation Note. . . . . . . . 02-13–3
Cap Installation Note . . . . . . . . . . . . . . 02-13–4
FRONT SHOCK ABSORBER AND
SPRING DISASSEMBLY/
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . 02-13–4
Piston Rod Nut Disassembly Note . . . . 02-13–5
Coil Spring Assembly Note . . . . . . . . . 02-13–5
Upper Spring Seat Assembly Note . . . 02-13–5
Mounting Rubber Assembly Note . . . . 02-13–6
FRONT SHOCK ABSORBER
INSPECTION . . . . . . . . . . . . . . . . . . . . . 02-13–6
FRONT SHOCK ABSORBER
DISPOSAL . . . . . . . . . . . . . . . . . . . . . . 02-13–6
FRONT LOWER ARM
REMOVAL/INSTALLATION. . . . . . . . . . 02-13–7
FRONT LOWER ARM INSPECTION . . . 02-13–7
FRONT STABILIZER
REMOVAL/INSTALLATION . . . . . . . . . . 02-13–8
Front Stabilizer Installation Note . . . . . . 02-13–8
Stabilizer Bushing Installation Note. . . . 02-13–9
Stabilizer Bracket Installation Note . . . . 02-13–9
STABILIZER CONTROL LINK
INSPECTION . . . . . . . . . . . . . . . . . . . . . 02-13–9
FRONT CROSSMEMBER
REMOVAL/INSTALLATION . . . . . . . . . . 02-13–10
Tie-rod End Ball Joint
Removal Note. . . . . . . . . . . . . . . . . . . 02-13–11
Steering Gear And Linkage,
Front Stabilizer, Front Lower Arm
And Front Crossmember
Component Removal Note . . . . . . . . . 02-13–11
Front Crossmember Mounting
Rubber (front) Installation Note . . . . . . 02-13–12
Front Crossmember Mounting
Rubber (rear) Installation Note . . . . . . 02-13–12
Steering Gear And Linkage,
Front Stabilizer, Front Lower Arm
And Front Crossmember
Component Installation Note. . . . . . . . 02-13–13
TRANSVERSE MEMBER
REMOVAL/INSTALLATION . . . . . . . . . . 02-13–14
End of Toc
WM: SUSPENSION
FRONT SUSPENSION
02-13–2
2007 Mazda CX-7 Workshop Manual (1871–1U–06B)
FRONT SUSPENSION LOCATION INDEX
id021300800100
.
End Of Sie
WM: FRONT SHOCK ABSORBER AND SPRING
1
2
5
6
4
7
3
acxuuw00001673
1
Front shock absorber and coil spring
(See 02-13-3 FRONT SHOCK ABSORBER AND
SPRING REMOVAL/INSTALLATION)
(See 02-13-4 FRONT SHOCK ABSORBER AND
SPRING DISASSEMBLY/ASSEMBLY)
2
Front shock absorber
(See 02-13-6 FRONT SHOCK ABSORBER
INSPECTION)
(See 02-13-6 FRONT SHOCK ABSORBER
DISPOSAL)
3
Front lower arm
(See 02-13-7 FRONT LOWER ARM REMOVAL/
INSTALLATION)
(See 02-13-7 FRONT LOWER ARM INSPECTION)
4
Front stabilizer
(See 02-13-8 FRONT STABILIZER REMOVAL/
INSTALLATION)
5
Stabilizer control link
(See 02-13-9 STABILIZER CONTROL LINK
INSPECTION)
6
Front crossmember
(See 02-13-10 FRONT CROSSMEMBER
REMOVAL/INSTALLATION)
7
Transverse member
(See 02-13-14 TRANSVERSE MEMBER
REMOVAL/INSTALLATION)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст