Mazda CX 7. Manual — part 390
SEATS
09-13–9
09-13
REMOTE HANDLE LEVER REMOVAL/INSTALLATION
id091300800600
1. To remove the remote wire, remove the trunk side trim. (See 09-17-24 TRUNK SIDE TRIM REMOVAL/
INSTALLATION.)
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
End Of Sie
WM: POWER SEAT
FRONT TILT MOTOR INSPECTION
id091300800700
1. Disconnect the front tilt motor connector.
2. Apply battery positive voltage to the front tilt motor
terminals and inspect the front tilt motor operation
• If not as specified, replace the slide adjuster.
End Of Sie
REAR TILT MOTOR INSPECTION
id091300800800
1. Disconnect the rear tilt motor connector.
2. Apply battery positive voltage to the rear tilt motor
terminals and inspect the rear tilt motor operation
• If not as specified, replace the slide adjuster.
End Of Sie
1
Screw
2
Cover
3
Remote wire
1
3
3
2
acxuuw00000940
Motor operation
Connection
B+
GND
Up
A
B
Down
B
A
B
A
UP
DOWN
M
B
A
acxuuw00000791
Motor operation
Connection
B+
GND
Up
B
A
Down
A
B
B
A
UP
DOWN
M
B
A
acxuuw00000904
SEATS
09-13–10
SLIDE MOTOR INSPECTION
id091300800900
1. Disconnect the slide motor connector.
2. Apply battery positive voltage to the slide motor
terminals and inspect the slide motor operation
• If not as specified, replace the slide adjuster.
End Of Sie
RECLINER MOTOR INSPECTION
id091300801000
1. Disconnect the recliner motor connector.
2. Apply battery positive voltage to the recliner
motor terminals and inspect the recliner motor
operation.
• If not as specified, replace the slide adjuster.
End Of Sie
Motor operation
Connection
B+
GND
Forward
A
B
Backward
B
A
B
A
FORWARD
BACKWARD
M
B
A
acxuuw00000776
Motor operation
Connection
B+
GND
Forward
B
A
Backward
A
B
B
A
FORWARD
BACKWARD
M
B
A
acxuuw00000905
SEATS
09-13–11
09-13
POWER SEAT SWITCH INSPECTION
id091300801100
1. Disconnect the power seat switch connector.
2. Inspect for continuity between the power seat switch connector terminals using an ohmmeter.
• If not as specified, replace the power seat switch.
End Of Sie
WM: SEAT WARMER
SEAT WARMER SWITCH REMOVAL/INSTALLATION
id091300801200
1. Disconnect the negative battery cable.
2. Remove the panel. (See 09-17-13 CONSOLE
REMOVAL/INSTALLATION.)
3. Install in the reverse order of removal.
J
H
K
L
: Continuity
Switch position
Recliner
Slide
Front tilt
Rear tilt
RECLINER
SLIDE
FRONT TILT
REAR TILT
Off
Off
Off
Off
Forward
Forward
Up
Up
Terminal
B
A
B
C
D
E
G
Backward
Backward
Down
Down
J
H
K
L
A
B
C
D
E
G
UP
DOWN
FORWARD
BACKWARD
DOWN
FORWARD
BACKWARD
UP
A
B
C
D
E
*
G
H
*
J
K
L
acxuuw00000757
TAB
TAB
SEAT WARMER SWITCH
acxuuw00000754
SEATS
09-13–12
Seat Warmer Switch Removal Note
1. Squeeze the tabs of seat warmer switch and pull it outward to remove it.
End Of Sie
SEAT WARMER SWITCH INSPECTION
id091300801300
1. Inspect for continuity between the seat warmer
switch terminals using an ohmmeter.
• If not as specified, replace the seat warmer
switch.
End Of Sie
SEAT WARMER UNIT INSPECTION
id091300801400
Seat Cushion
1. Remove the front seat. (See 09-13-2 FRONT SEAT REMOVAL/INSTALLATION.)
2. Remove the seat cushion trim. (See 09-13-2 FRONT SEAT DISASSEMBLY/ASSEMBLY.)
3. While inspecting for continuity between the
connector terminals A and B, use a dryer to warm
the thermostat of the seat warmer unit on seat
cushion.
4. When the ohmmeter indicates that there is no
continuity, turn off the dryer, then use a
thermometer to measure the temperature of the
thermostat.
5. Verify that the temperature is approx. 37
°C {99
°F}.
B
A
G
H
F
B
*
A
G
H
F
B
*
A
G
H
F
DRIVER'S SIDE
PASSENGER'S SIDE
B6U0913W017
: Bulb
Switch position
ON
OFF
Terminal
A
H
F
G
B
: Continuity
A6E7752W024
HOT AIR
THERMOSTAT
CONNECTOR
A
B
acxuuw00000906
THERMOMETER
THERMOSTAT
acxuuw00000907
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст