Mazda CX 7. Manual — part 425
WIPER/WASHER SYSTEM
09-19–7
09-19
WINDSHIELD WASHER HOSE REMOVAL/INSTALLATION
id091900802100
1. Remove the mudguard (RH).
2. Disconnect windshield washer hose A from the
windshield washer motor.
3. Remove windshield washer hose A from clip A.
4. Disconnect joint pipe A and remove windshield
washer hose A, B.
5. Remove the windshield wiper arm and blade.
(See.09-19-3 WINDSHIELD WIPER ARM AND
BLADE REMOVAL/INSTALLATION.)
6. Remove the cowl grill. (See.09-16-11 COWL
GRILLE REMOVAL/INSTALLATION.)
7. Remove windshield washer hose B from hook.
8. Disconnect windshield washer hose C from the
washer nozzle.
9. Disconnect windshield washer hose D from the
washer nozzle.
10. Disconnect joint pipe B and remove windshield
washer hose C, B and D.
11. Install in the reverse order of removal.
End Of Sie
WM: WASHER FLUID-LEVEL SENSOR
WASHER FLUID-LEVEL SENSOR REMOVAL/INSTALLATION
id091900801800
1. Disconnect the negative battery cable.
2. Remove the washer tank. (See 09-19-5 WASHER TANK REMOVAL/INSTALLATION.)
3. Disconnect the connector.
4. Remove the washer fluid-level sensor.
5. Remove the grommet.
6. Install in the reverse order of removal.
End Of Sie
JOINT PIPE A
CLIP A
WINDSHIELD WASHER HOSE A
WINDSHIELD WASHER
HOSE B
acxuuw00001820
HOOK
JOINT PIPE B
WINDSHIELD WASHER
HOSE D
WINDSHIELDWASHER
HOSE B
WINDSHIELD WASHER
HOSE C
acxuuw00001821
GROMMET
CONNECTOR
WASHER
FLUID-LEVEL
SENSOR
acxuuw00001831
WIPER/WASHER SYSTEM
09-19–8
WASHER FLUID-LEVEL SENSOR INSPECTION
id091900801900
1. Disconnect the negative battery cable.
2. Inspect for continuity between the washer fluid-
level sensor terminals using an ohmmeter.
• If not as specified, replace the washer fluid-
level sensor.
End Of Sie
WM: WIPER AND WASHER SWITCH
WIPER AND WASHER SWITCH REMOVAL/INSTALLATION
id091900800200
1. Disconnect the negative battery cable.
2. Remove the column cover. (See 09-17-8 COLUMN COVER REMOVAL/INSTALLATION.)
3. Disconnect the wiper and washer switch
connector.
4. Remove the screws, then remove the wiper and
washer switch.
5. Install in the reverse order of removal.
End Of Sie
WINDSHIELD WIPER AND WASHER SWITCH INSPECTION
id091900800300
1. Verify that the continuity between the windshield
wiper and washer switch is as indicated in the
table.
• If not as indicated in the table, replace the
wiper and washer switch.
End Of Sie
A
B
acxuuw00001885
B
A
Fluid level
Terminal
: Continuity
Above low
Below low
acxuuw00001886
CONNECTOR
SCREW
WIPER AND WASHER
SWITCH
acxuuw00001781
C
K
M
A
O
E
K
C
E
O
A
*
M
INT
2
1
OFF
MIST
INT
VOL
INT
OFF
2
1
*
*
*
*
*
*
*
WINDSHIELD
WASHER
SWITCH
acxuuw00001621
OFF
INT
1
2
OFF
ON
ON
Mist
A
C
E
K
O
: Continuity
Switch position
Terminal
Windshield
wiper switch
Windshield
washer switch
acxuuw00001622
WIPER/WASHER SYSTEM
09-19–9
09-19
REAR WIPER AND WASHER SWITCH INSPECTION
id091900800400
1. Verify that the continuity between the rear wiper
and washer switch terminals is as indicated in the
table.
• If not as indicated in the table, replace the
wiper and washer switch.
End Of Sie
WM: REAR WIPER ARM AND BLADE
REAR WIPER ARM AND BLADE REMOVAL/INSTALLATION
id091900801200
1. Remove in the order indicated in the table.
2. Install in the reverse order of removal.
3. Adjust the rear wiper arm and blade. (See 09-19-
10 REAR WIPER ARM AND BLADE
ADJUSTMENT.)
Rear Wiper Arm Installation Note
1. Clean the rear wiper arm connector shaft using a
wire brush before installing the rear wiper arm.
End Of Sie
F
H
*
*
*
*
F
H
J
L
*
*
REAR WASHER
SWITCH
REAR
WIPER
INT
REAR
WIPER
ON
J
L
*
*
*
*
acxuuw00001627
INT
OFF
ON
ON
ON
F
H
J
L
Switch position
Rear wiper
switch
Rear washer
switch
Rear wiper
and washer
switch
Terminal
: Continuity
acxuuw00001628
1
Cap
2
Nut
3
Rear wiper arm
(See 09-19-9 Rear Wiper Arm Installation Note.)
4
Rear wiper blade
5
Rubber brush
6
Backing plate
5.9—9.8 N·m
{61—99 kgf·cm,
53—86 in·lbf}
5
4
3
1
2
6
acxuuw00001783
REAR WIPER ARM
CONNECTOR
SHAFT
acxuuw00001784
WIPER/WASHER SYSTEM
09-19–10
REAR WIPER ARM AND BLADE ADJUSTMENT
id091900801300
1. Turn off the rear wiper switch while operating the rear wiper motor, and then stop the rear wiper at the auto-stop
position.
2. Set the rear wiper arm onto the ceramic end line.
End Of Sie
WM: REAR WIPER MOTOR
REAR WIPER MOTOR REMOVAL/INSTALLATION
id091900801400
1. Disconnect the negative battery cable.
2. Remove the rear wiper arm and blade. (See 09-19-9 REAR WIPER ARM AND BLADE REMOVAL/
INSTALLATION.)
3. Remove the liftgate upper trim. (See 09-17-25 LIFTGATE UPPER TRIM REMOVAL/INSTALLATION.)
4. Remove the liftgate side trim. (See 09-17-25 LIFTGATE SIDE TRIM REMOVAL/INSTALLATION.)
5. Remove the liftgate lower trim. (See 09-17-26 LIFTGATE LOWER TRIM REMOVAL/INSTALLATION.)
6. Remove in the order indicated in the table.
7. Install in the reverse order of removal.
End Of Sie
REAR WIPER MOTOR INSPECTION
id091900801500
1. Connect battery positive voltage to the rear wiper motor terminal A, and ground the rear wiper motor terminal B.
2. Verify that the rear wiper motor operates.
• If there is any malfunction, replace the rear
wiper motor.
End Of Sie
WM: REAR WASHER MOTOR
CERAMIC END LINE
0—30 mm
{0—1.1 in}
CERAMIC
END LINE
acxuuw00001791
1
Rear wiper motor connector
2
Bolt
3
Rear wiper motor
2
1
2
4.0—6.8 N·m
{41—69 kgf·cm,
36—60 in·lbf}
BOLT :
3
acxuuw00001782
B
A
B
A
M
AUTOSTOP
SWITCH
acxuuw00001630
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст