Mazda CX 7. Manual — part 429
ENTERTAINMENT
09-20–9
09-20
3. Remove in the order indicated in the table.
.
4. Install in the reverse order of removal.
End Of Sie
REAR SPEAKER INSPECTION
id092000802500
1. Verify the resistance between front speaker
terminals.
• If the resistance is not within the specification,
replace the front speaker.
Resistance
3.6 ohms
2. Connect a 1.5 V battery to the front speaker and
verify that noise is heard from the front speaker.
• If no noise is heard, replace the front speaker.
End Of Sie
CENTER SPEAKER REMOVAL/INSTALLATION
id092000806000
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
.
3. Install in the reverse order of removal.
End Of Sie
CENTER SPEAKER INSPECTION
id092000806100
1. Verify the resistance between center speaker
terminals.
• If the resistance is not within the specification,
replace the center speaker.
Resistance
3.6 ohms
2. Connect a 1.5 V battery to the center speaker and
verify that noise is heard from the center speaker.
• If no noise is heard, replace the center
speaker.
End Of Sie
WM: MICROPHONE
1
Screw
2
Connector
3
Rear speaker
3
1
2
1
acxuuw00001808
A
B
A
B
acxuuw00001809
1
Cover
2
Screw
3
Speaker
4
Connector
1
3
2
4
acxuuw00001815
A
B
A
B
acxuuw00001810
1871-1U-06B(09-20).fm 9 ページ 2006年3月15日 水曜日 午後12時49分
ENTERTAINMENT
09-20–10
AUDIOPILOT MICROPHONE REMOVAL/INSTALLATION
id092000806300
Note
• "AudioPilot" is a registered trademark of Bose Corporation.
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
.
3. Install in the reverse order of removal.
End Of Sie
WM: ANTENNA
CENTER ROOF ANTENNA REMOVAL/INSTALLATION
id092000801600
1. Disconnect the negative battery cable.
2. Remove the following parts:
(1) Rear scuff plate inner (See 09-17-19 REAR SCUFF PLATE REMOVAL/INSTALLATION.)
(2) Rear seat (See 09-13-7 REAR SEAT REMOVAL/INSTALLATION.)
(3) Sub trunk box (See 09-17-25 SUB TRUNK BOX REMOVAL/INSTALLATION.)
(4) Trunk end trim (See 09-17-24 TRUNK END TRIM REMOVAL/INSTALLATION.)
(5) Trunk side trim (See 09-17-24 TRUNK SIDE TRIM REMOVAL/INSTALLATION.)
(6) C-pillar trim (See 09-17-17 C-PILLAR TRIM REMOVAL/INSTALLATION.)
(7) D-pillar trim (See 09-17-18 D-PILLAR TRIM REMOVAL/INSTALLATION.)
(8) Assist handle (See 09-17-27 ASSIST HANDLE REMOVAL/INSTALLATION.)
3. Partially peel back the headliner.
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
6. After installation, verify that the rubber of the
center roof antenna is installed to the roof panel
with no space between them.
End Of Sie
1
Connector
2
Screw
3
AudioPilot microphone
3
1
2
acxuuw00002282
1
Antenna rod
2
Connector
3
Nut
4
Center roof antenna
5
Rubber
1
2
3
5
4
0.98—2.9 N·m
{10—30 kgf·cm, 8.7—26 in·lbf}
acxuuw00001021
1871-1U-06B(09-20).fm 10 ページ 2006年3月15日 水曜日 午後12時49分
ENTERTAINMENT
09-20–11
09-20
2007 Mazda CX-7 Workshop Manual (1871–1U–06B)
CENTER ROOF ANTENNA INSPECTION
id092000801700
Note
• The center roof antenna has a built-in antenna amplifier.
Antenna Amplifier Inspection
1. Turn the audio unit on and select the radio, then
measure the voltage at center roof antenna
connector terminal A.
• If the voltage is B+, go to the Feeder Line
Inspection.
• If the voltage is not B+, inspect the audio unit or
antenna feeder.
Feeder Line Inspection
1. Verify that there is no continuity between the
center roof antenna terminals A and C using an
ohmmeter.
2. Inspect for continuity between the center roof
antenna terminals using an ohmmeter.
• If not as indicated in the table, replace the
center roof antenna.
End Of Sie
WM: GPS ANTENNA
GPS ANTENNA REMOVAL/INSTALLATION
id092000801500
1. Disconnect the negative battery cable.
2. Remove the meter hood. (See 09-17-10 METER HOOD REMOVAL/INSTALLATION.)
3. Remove the instrument cluster. (See 09-22-2 INSTRUMENT CLUSTER REMOVAL/INSTALLATION.)
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
End Of Sie
WM: ANTENNA FEEDER
B
A
C
CENTER ROOF ANTENNA
HARNESS-SIDE CONNECTOR
acxuuw00002199
B
A
C
acxuuw00002283
B
C
A
Test condition
Terminal
Body
GND
: Continuity
Under any condition
acxuuw00002201
1
Screw
2
Connector
3
GPS antenna
1
3
2
acxuuw00001020
ENTERTAINMENT
09-20–12
2007 Mazda CX-7 Workshop Manual (1871–1U–06B)
Revised 1/2007 (Ref. No. R027/07)
ANTENNA FEEDER LOCATION
id092000801800
Caution
• If the antenna feeder is installed with tension on the cable and wiring harness it could result in
loosening of the connection areas and poor contact. When installing and connecting the antenna
feeder, always make sure there is slack on the cable and wiring harness.
Note
• The antenna feeder is integrated with the vehicle wiring harness.
• When installing a new antenna feeder, secure it to the vehicle wiring harness along the installation route of
the old antenna feeder.
End Of Sie
FRONT ANTENNA FEEDER INSPECTION
id092000801900
1. Verify that the continuity is as indicated in the
table.
• If not as indicated in the table, replace the
front antenna feeder.
End Of Sie
FRONT ANTENNA FEEDER
REAR ANTENNA FEEDER
GPS ANTENNA FEEDER NO.1
GPS ANTENNA FEEDER NO.2
acxuuw00002583
E
D
C
F
B
A
acxuuw00002070
: Continuity
Test
condition
Under
any
condition
Terminal
B
C
D
E
F
A
acxuuw00002071
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст