Mazda CX 7. Manual — part 393
SECURITY AND LOCKS
09-14–7
09-14
FRONT DOOR LOCK ACTUATOR INSPECTION
id091400800800
1. Apply battery positive voltage and connect ground
to the corresponding front door lock actuator
terminals, and inspect the front door lock actuator
operation.
• If not as specified, replace the front door latch
and lock actuator.
End Of Sie
REAR DOOR LOCK ACTUATOR INSPECTION
id091400800900
1. Apply battery positive voltage and connect ground
to the corresponding front door lock actuator
terminals, and inspect the front door lock actuator
operation.
• If not as specified, replace the front door latch
and lock actuator.
End Of Sie
DOOR LOCK-LINK SWITCH INSPECTION
id091400801200
Front/rear
1. Inspect for continuity between the door lock-link
switch terminals.
• If not as specified, replace the front door latch
and lock actuator.
End Of Sie
FRONT DOOR KEY CYLINDER SWITCH INSPECTION
id091400801300
1. Inspect for continuity between the front door key
cylinder switch terminals.
• If not as specified, replace the front door latch
and lock actuator.
Lock actuator
operation
Connection
B+
GND
Lock
LH: 1A
RH: 1B
LH: 1B
RH: 1A
Unlock
LH: 1B
RH: 1A
LH: 1A
RH: 1B
1B
1A
M
LOCK UNLOCK
RH: 1B
RH: 1A
1A
1B
acxuuw00002469
Lock actuator
operation
Connection
B+
GND
Lock
LH: 1A
RH: 1B
LH: 1B
RH: 1A
Unlock
LH: 1B
RH: 1A
LH: 1A
RH: 1B
1B
1A
M
LOCK UNLOCK
RH: 1B
RH: 1A
1A
1B
acxuuw00002470
2E
2B
LOCK
UNLOCK
2F
RH: 2B
RH: 2E
RH: 2A
2E
2F
2A
2B
2E
2B 2A
LH
RH
acxuuw00002471
: Continuity
Lock knob
position
Lock
Unlock
Terminal
LH: 2B
RH: 2E
LH: 2E
RH: 2B
LH: 2F
RH: 2A
acxuuw00002472
2B
2A
2E
2F
2A
2B
LOCK
UNLOCK
acxuuw00002473
2A
2B
R
R : 1 k ohm
Key cylinder
position
Lock
Unlock
: Continuity
Terminal
acxuuw00002474
SECURITY AND LOCKS
09-14–8
End Of Sie
DOOR LOCK SWITCH REMOVAL/INSTALLATION
id091400801400
1. Disconnect the negative battery cable.
2. Remove the inner handle cover. (See 09-17-20 FRONT DOOR TRIM REMOVAL/INSTALLATION.)
3. Remove the screws, then remove the door lock
switch.
4. Install in the reverse order of removal.
End Of Sie
DOOR LOCK SWITCH INSPECTION
id091400801500
1. Inspect for continuity between the door lock
switch terminals using an ohmmeter.
• If not as specified, replace the door lock
switch.
End Of Sie
DOOR LOCK STRIKER REMOVAL/INSTALLATION
id091400801600
1. Remove the screws, then remove the door lock
striker.
2. Install in the reverse order of removal.
3. Adjust the door. (See 09-11-3 DOOR
ADJUSTMENT.)
End Of Sie
WM: OPEN HANDLE
FRONT OUTER HANDLE REMOVAL/INSTALLATION
id091400803100
1. Disconnect the negative battery cable.
2. Fully roll up the front door glass.
3. Remove the inner garnish. (See 09-17-20 INNER GARNISH REMOVAL/INSTALLATION.)
4. Remove the front door trim. (See 09-17-20 FRONT DOOR TRIM REMOVAL/INSTALLATION.)
5. Remove the hole cover.
6. Detach the rod from the outer handle.
DOOR LOCK
SWITCH
SCREW
acxuuw00002475
UNLOCK
LOCK
C
D
B
A
A
B
C
D
acxuuw00002476
R: 940—1,060 ohms
D
C
: Continuity
Lock
Unlock
Position
Terminal
: Resistance
R
acxuuw00002477
SCREW
17.6—26.5 N·m
{1.80—2.70 kgf·m,
13.0—19.5 ft·lbf}
DOOR LOCK STRIKER
acxuuw00002478
SECURITY AND LOCKS
09-14–9
09-14
7. Secure the rear part of the front outer handle and,
with the front outer handle lever pulled outward
(1), remove the rear part of the front outer handle
from the front door.
8. Pull out the front side of the front outer handle
from the front door.
9. Install in the reverse order of removal.
End Of Sie
REAR OUTER HANDLE REMOVAL/INSTALLATION
id091400803200
1. Disconnect the negative battery cable.
2. Fully roll up the rear door glass.
3. Remove the rear door trim. (See 09-17-23 REAR DOOR TRIM REMOVAL/INSTALLATION.)
4. Secure the rear part of the rear outer handle and,
with the rear outer handle lever pulled outward
(1), remove the rear part of the rear outer handle
from the rear door.
5. Install in the reverse order of removal.
End Of Sie
INNER HANDLE REMOVAL/INSTALLATION
id091400803300
1. Disconnect the negative battery cable.
2. Remove the front door trim or rear door trim. (See 09-17-20 FRONT DOOR TRIM REMOVAL/INSTALLATION.)
(See 09-17-23 REAR DOOR TRIM REMOVAL/INSTALLATION.)
3. Detach the cables from the inner handle and door
lock knob.
4. Install in the reverse order of removal.
End Of Sie
WM: LIFTGATE LOCK
LIFTGATE OUTER HANDLE REMOVAL/INSTALLATION
id091400803700
1. Remove the rear finisher. (See 09-16-3 REAR FINISHER REMOVAL/INSTALLATION.)
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
End Of Sie
OUTER HANDLE
FRONT
(1)
acxuuw00002479
OUTER HANDLE
FRONT
(1)
acxuuw00002480
INNER
HANDLE
CABLE
acxuuw00002481
1
Nut
2
Liftgate outer handle
3.9—5.9 N·m
{39.8—60.1 kgf·cm,
34.6—52.2 in·lbf}
1
2
acxuuw00002482
SECURITY AND LOCKS
09-14–10
LIFTGATE LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION
id091400803800
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
End Of Sie
LIFTGATE LOCK ACTUATOR INSPECTION
id091400803900
1. Apply battery positive voltage and connect ground
to the corresponding liftgate lock actuator
terminals, and inspect the liftgate lock actuator
operation.
• If not as specified, replace the liftgate latch
and lock actuator.
End Of Sie
LIFTGATE LATCH SWITCH INSPECTION
id091400804000
1. When inspecting the latch, press the latch lever
using a flathead screwdriver or a similar tool.
2. Inspect for continuity between the liftgate latch
switch terminals.
• If not as specified, replace the liftgate latch
and lock actuator.
End Of Sie
1
Bolt
2
Connector
3
Liftgate latch and lock actuator
A
A
B
B
C
C
6.90—9.80 N·m {70—100 kgf·cm, 60.8—86.7 in·lbf}
3
1
2
acxuuw00002483
Lock actuator
operation
Connection
B+
GND
Lock
A
B
Unlock
B
A
A
B
B
A
M
LOCK UNLOCK
acxuuw00002484
LEVER
acxuuw00002485
A
B
B
A
acxuuw00002486
: Continuity
Latch condition
Terminal
B
A
Latch (liftgate is closed)
Unlatch (liftgate is open)
acxuuw00002487
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст