Mazda CX 7. Manual — part 377
DOORS AND LIFTGATE
09-11–1
09-11
09-11
DOORS AND LIFTGATE
LOCATION INDEX. . . . . . . . . . . . . . . . . . 09-11–1
FRONT DOOR
REMOVAL/INSTALLATION. . . . . . . . . . 09-11–2
Connector Removal Note. . . . . . . . . . . 09-11–2
REAR DOOR
REMOVAL/INSTALLATION. . . . . . . . . . 09-11–3
DOOR ADJUSTMENT. . . . . . . . . . . . . . . 09-11–3
FRONT DOOR UNIT
REMOVAL/INSTALLATION . . . . . . . . . . 09-11–4
REAR DOOR UNIT
REMOVAL/INSTALLATION . . . . . . . . . . 09-11–4
LIFTGATE
REMOVAL/INSTALLATION . . . . . . . . . . 09-11–5
LIFTGATE ADJUSTMENT . . . . . . . . . . . . 09-11–6
STAY DAMPER DISPOSAL . . . . . . . . . . . 09-11–6
End of Toc
WM: DOOR
LOCATION INDEX
id091100800100
.
End Of Sie
2
4
1
3
5
acxuuw00001326
1
Front door
(See 09-11-2 FRONT DOOR REMOVAL/
INSTALLATION.)
(See 09-11-3 DOOR ADJUSTMENT.)
2
Rear door
(See 09-11-3 REAR DOOR REMOVAL/
INSTALLATION.)
(See 09-11-3 DOOR ADJUSTMENT.)
3
Front door unit
(See 09-11-4 FRONT DOOR UNIT REMOVAL/
INSTALLATION.)
4
Rear door unit
(See 09-11-4 FRONT DOOR UNIT REMOVAL/
INSTALLATION.)
5
Liftgate
(See 09-11-5 LIFTGATE REMOVAL/
INSTALLATION.)
(See 09-11-6 LIFTGATE ADJUSTMENT.)
DOORS AND LIFTGATE
09-11–2
FRONT DOOR REMOVAL/INSTALLATION
id091100800200
1. Disconnect the negative battery cable.
2. To remove the checker, remove the following parts:
(1) Inner garnish (See09-17-20 INNER GARNISH REMOVAL/INSTALLATION)
(2) Front door trim (See09-17-20 FRONT DOOR TRIM REMOVAL/INSTALLATION)
(3) Front door speaker (See09-20-6 FRONT DOOR SPEAKER REMOVAL/INSTALLATION)
3. To remove the front door hinges, remove the following parts:
(1) Windshield wiper arm and blade (See09-19-3 WINDSHIELD WIPER ARM AND BLADE REMOVAL/
INSTALLATION)
(2) Cowl grill (See09-16-11 COWL GRILLE REMOVAL/INSTALLATION)
(3) Front bumper (See09-10-2 FRONT BUMPER REMOVAL/INSTALLATION)
(4) Front combination lights (See09-18-5 FRONT COMBINATION LIGHT REMOVAL/INSTALLATION)
(5) Side step molding (See09-16-14 SIDE STEP MOLDING REMOVAL)
(6) Front fender panel (See09-10-7 FRONT FENDER PANEL REMOVAL/INSTALLATION)
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
6. Adjust the front door. (See 09-11-3 DOOR ADJUSTMENT.)
Connector Removal Note
1. Pull down the cover in the direction of the arrow
and disconnect the connector.
End Of Sie
8
7
N·m {kgf·m, ft·lbf}
7.9—12.7 N·m
{80.6—129.5 kgf·cm,
70.0—112.4 in·lbf}
17.6—29.4
{1.8—2.9,
13.0—21.6}
17.6—30.4
{1.8—3.0,
13.0—22.4}
17.6—30.4
{1.8—3.0,
13.0—22.4}
14.0—20.0
{1.43—2.04,
10.3—14.7}
6
5
2
3
3
1
6
4
acxuuw00001327
1
Connector
(See 09-11-2 Connector Removal Note.)
2
Bolt A
3
Bolt B
4
Front door
5
Bolt C
6
Checker
7
Bolt D
8
Front door hinge
COVER
acxuuw00001328
DOORS AND LIFTGATE
09-11–3
09-11
REAR DOOR REMOVAL/INSTALLATION
id091100800300
1. To remove the checker, remove the following parts:
(1) Inner garnish (See09-17-20 INNER GARNISH REMOVAL/INSTALLATION)
(2) Rear door trim (See09-17-23 REAR DOOR TRIM REMOVAL/INSTALLATION)
(3) Rear door speaker (See09-20-7 REAR DOOR SPEAKER REMOVAL/INSTALLATION)
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
4. Adjust the front door. (See 09-11-3 DOOR ADJUSTMENT.)
End Of Sie
DOOR ADJUSTMENT
id091100800400
1. Loosen the door hinge installation bolts.
2. Adjust the gap and height difference to the
standard range by moving the door back and
forth, left and right.
Clearance
a: 2.5— 4.5 mm {0.10— 0.17 in}
d: -1.0— 1.0 mm {-0.03— 0.03 in}
3. Tighten the bolts or screws.
4. If the front door and rear door dose not open/
close smoothly, loosen the door
End Of Sie
WM: DOOR UNIT
N·m {kgf·m, ft·lbf}
1
6
4
7.9—12.7 N·m
{80.6—129.5 kgf·cm,
70.0—112.4 in·lbf}
5
6
7
8
17.6—29.4
{1.8—2.9,
13.0—21.6}
14.0—20.0
{1.43—2.04,
10.3—14.7}
2
17.6—30.4
{1.8—3.0,
13.0—22.4}
3
17.6—30.4
{1.8—3.0,
13.0—22.4}
3
acxuuw00001329
1
Connector
2
Bolt A
3
Bolt B
4
Rear door
5
Bolt C
6
Checker
7
Bolt D
8
Rear door hinge
a
a
b
b
(+)
(-)
(+)
(-)
A
B
B
C
C
A
SEC. A
—
A
REAR
FENDER
PANEL
REAR
DOOR
PANEL
REAR
DOOR
PANEL
FRONT
DOOR
PANEL
FRONT
DOOR
PANEL
FRONT
FENDER
PANEL
SEC. B
—
B
SEC. C
—
C
a
b
acxuuw00001330
DOORS AND LIFTGATE
09-11–4
FRONT DOOR UNIT REMOVAL/INSTALLATION
id091100800500
1. Disconnect the negative battery cable.
2. Remove the following parts:
(1) Inner garnish (See09-17-20 INNER GARNISH REMOVAL/INSTALLATION)
(2) Front door trim (See09-17-20 FRONT DOOR TRIM REMOVAL/INSTALLATION)
(3) Front door speaker (See09-20-6 FRONT DOOR SPEAKER REMOVAL/INSTALLATION)
(4) Front door glass (See09-12-3 FRONT DOOR GLASS REMOVAL/INSTALLATION)
(5) Inner handle (See09-14-9 INNER HANDLE REMOVAL/INSTALLATION)
3. Disconnect the power outer mirror connector.
4. Disconnect the front door wiring harness connector. (See 09-11-2 FRONT DOOR REMOVAL/INSTALLATION.)
5. Remove the tab, then remove the front door
wiring harness bracket.
6. Remove screws A and fastener.
7. Remove the front door module.
8. Install in the reverse order of removal.
End Of Sie
REAR DOOR UNIT REMOVAL/INSTALLATION
id091100800600
1. Disconnect the negative battery cable.
2. Remove the following parts:
(1) Inner garnish (See09-17-20 INNER GARNISH REMOVAL/INSTALLATION)
(2) Rear door trim (See09-17-23 REAR DOOR TRIM REMOVAL/INSTALLATION)
(3) Rear door speaker (See09-20-7 REAR DOOR SPEAKER REMOVAL/INSTALLATION)
(4) Rear door glass (See09-12-4 REAR DOOR GLASS REMOVAL/INSTALLATION)
(5) Inner handle (See09-14-9 INNER HANDLE REMOVAL/INSTALLATION)
3. Disconnect the rear door wiring harness connector. (See 09-11-3 REAR DOOR REMOVAL/INSTALLATION.)
FRONT DOOR
WIRING HARNESS
BRACKET
TAB
acxuuw00001331
A
A
A
A
A
A
A
A
A
A
FASTENER
SCREW A
FRONT DOOR
MODULE
acxuuw00001332
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст