Mazda CX 7. Manual — part 276
POWER STEERING
06-14–21
06-14
2. Lock the steering rack end against rotation with a
suitable wrench and install the other side tie rod
using the SST.
Substitution SST
• 49 H032 351
Width across flats 34mm {1.3 in} (Torque
control enabled wrench)
Boot Assembly Note
1. Apply silicone grease to the rubber lip groove.
2. Assemble the boot.
End Of Sie
WM: POWER STEERING OIL PUMP
POWER STEERING OIL PUMP REMOVAL/INSTALLATION
id061400800700
1. Remove the drive belt. (See 01-10-3 DRIVE BELT REMOVAL/INSTALLATION[L3 WITH TC].)
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
.
End Of Sie
49 H032 351
SUITABLE WRENCH
acxuuw00002262
2
1
4
3
R
R
N·m {kgf·m, ft·lbf}
18.6—25.5
{1.9—2.6, 14—18}
18.6—25.5
{1.9—2.6, 14—18}
R
29.4—44.1
{3.00—4.49, 21.7—32.5}
acxuuw00001346
1
Pressure switch connector
2
Pressure pipe
3
Return hose
4
Power steering oil pump
1871-1U-06B(06-14).fm 21 ページ 2006年3月15日 水曜日 午前11時25分
POWER STEERING
06-14–22
POWER STEERING OIL PUMP DISASSEMBLY/ASSEMBLY
id061400800800
Note
• The following procedure is for replacement of the O-ring and oil seal only. Replace the pump component if
other repairs are necessary.
1. Disassemble in the order indicated in the table.
2. Assemble in the reverse order of disassembly.
.
22
—
26 {2.3
—
2.6, 16.3
—
19.1}
49
—
69 {5.0
—
7.0, 36.2
—
50.8}
25.4
—29.4
{2.60
—2.99
, 18.8
—21.6
}
N·m {kgf·m, ft·lbf}
8
7
5
4
3
10
12
16
17
15
14
11
13
20
6
1
2
SST
R
R
R
R
ATF
ATF
ATF
19
R
ATF
R
ATF
R
9
18
R
SST
acxuuw00001915
1
Power steering oil pump component
(See 06-14-23 Power Steering Oil Pump
Component Disassembly Note.)
2
Pressure switch component
3
Connector
4
O-ring
5
Control valve
6
Spring
7
Clip
(See 06-14-23 Clip Disassembly Note.)
(See 06-14-25 Clip Assembly Note.)
8
Fluid reservoir
9
O-ring
10
Rear pump body
(See 06-14-25 Rear Pump Body Assembly Note.)
11
Gasket
12
Clip
1871-1U-06B(06-14).fm 22 ページ 2006年3月15日 水曜日 午前11時25分
POWER STEERING
06-14–23
06-14
Power Steering Oil Pump Component Disassembly Note
1. Secure the power pressure oil pump using the
SST.
Caution
• Use the SST to prevent damage to the
pump when securing it in a vise.
Clip Disassembly Note
1. Lift up the clip tab using a flathead screwdriver.
2. Remove the clip pushing with a flathead
screwdriver and a hammer as shown in the figure.
13
Cam ring
(See 06-14-25 Cam Ring Assembly Note.)
14
Rotor
(See 06-14-25 Rotor Assembly Note.)
15
Vane
16
Side plate
(See 06-14-24 Side plate Assembly Note.)
17
O-rings
18
Shaft component
(See 06-14-24 Shaft Component Disassembly
Note.)
19
Oil seal
(See 06-14-24 Oil seal Disassembly Note.)
(See 06-14-24 Oil seal Assembly Note.)
20
Front pump body
49 F032 301
acxuuw00002389
CLIP
R
acxuuw00001917
1871-1U-06B(06-14).fm 23 ページ 2006年3月15日 水曜日 午前11時25分
POWER STEERING
06-14–24
Shaft Component Disassembly Note
1. Tap out the shaft component from the front pump
body using a plastic hammer.
Oil seal Disassembly Note
1. Remove the oil seal from the front pump body
using a flathead screwdriver.
Oil seal Assembly Note
1. Install the oil seal in the front pump body using
the SST and plastic hammer.
Side plate Assembly Note
1. Install the side plate in the position shown in the
figure.
acxuuw00002347
acxuuw00002348
49 F032 321
acxuuw00001919
acxuuw00002349
1871-1U-06B(06-14).fm 24 ページ 2006年3月15日 水曜日 午前11時25分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст