Mazda CX 7. Manual — part 158
SYMPTOM TROUBLESHOOTING
02-03–9
02-03
When a replaced wheel unit and a registered wheel unit malfunction
When two replaced wheel units malfunction
When two replaced wheel units and a registered wheel unit malfunction
When three replaced wheel units malfunction
End Of Sie
WU_1
WU_2
WU_3
WU_4
ID Number (Stored)
0xAAAAAAAA
0xBBBBBBBB
0xCCCCCCCC
0xDDDDDDDD
ID Number (Candidate)
0xEEEEEEEE
0xFFFFFFFF
0x00000000
0x00000000
Tire Pressure (Stored)
0 kPa
0 kPa
0 kPa
0 kPa
Tire Pressure (Candidate)
eee kPa
fff kPa
0 kPa
0 kPa
WU_1
WU_2
WU_3
WU_4
ID Number (Stored)
0xAAAAAAAA
0xBBBBBBBB
0xCCCCCCCC
0xDDDDDDDD
ID Number (Candidate)
0xEEEEEEEE
0x00000000
0x00000000
0x00000000
Tire Pressure (Stored)
aaa kPa
0 kPa
0 kPa
0 kPa
Tire Pressure (Candidate)
eee kPa
0 kPa
0 kPa
0 kPa
WU_1
WU_2
WU_3
WU_4
ID Number (Stored)
0xAAAAAAAA
0xBBBBBBBB
0xCCCCCCCC
0xDDDDDDDD
ID Number (Candidate)
0xEEEEEEEE
0x00000000
0x00000000
0x00000000
Tire Pressure (Stored)
0 kPa
0 kPa
0 kPa
0 kPa
Tire Pressure (Candidate)
eee kPa
0 kPa
0 kPa
0 kPa
WU_1
WU_2
WU_3
WU_4
ID Number (Stored)
0xAAAAAAAA
0xBBBBBBBB
0xCCCCCCCC
0xDDDDDDDD
ID Number (Candidate)
0x00000000
0x00000000
0x00000000
0x00000000
Tire Pressure (Stored)
aaa kPa
0 kPa
0 kPa
0 kPa
Tire Pressure (Candidate)
0 kPa
0 kPa
0 kPa
0 kPa
1871-1U-06B(02-03).fm 9 ページ 2006年3月15日 水曜日 午前10時57分
GENERAL PROCEDURES
02-10–1
02-10
02-10
GENERAL PROCEDURES
PRECAUTION (SUSPENSION). . . . . . . . 02-10–1
Wheels and Tires
Removal/Installation. . . . . . . . . . . . . . 02-10–1
Suspension Links
Removal/Installation. . . . . . . . . . . . . . 02-10–1
Brake Lines
Disconnection/Connection . . . . . . . . . 02-10–1
Power Steering Components
Removal/Installation . . . . . . . . . . . . . . 02-10–1
End of Toc
WM: SUSPENSION
PRECAUTION (SUSPENSION)
id021000800100
Wheels and Tires Removal/Installation
1. When a wheel is installed, tighten it to
88.2— 117.6 N·m {9.00— 11.99 kgf·m, 65.06—
86.73 ft·lbf}.
Suspension Links Removal/Installation
1. Tighten any part of the suspension that uses rubber bushings only after the vehicle has been lowered to the
ground and unloaded.
Note
• Unloaded: Fuel tank is full. Engine coolant and engine oil are at specified levels. Spare tire, jack and tools
are in designated position.
Brake Lines Disconnection/Connection
Caution
• Brake fluid will damage painted surfaces. If brake fluid does get on a painted surface, wipe it off
immediately.
1. Tighten the brake pipe flare nut using the SST (49 0259 770B). Be sure to modify the brake pipe flare nut
tightening torque to allow for use of a torque wrench-SST combination.
(See 00-00-13 SERVICE CAUTIONS.)
2. If any brake line has been disconnected anytime during the procedure, add brake fluid, bleed the brakes, and
inspect for leakage after the procedure has been completed.
Power Steering Components Removal/Installation
1. If any steering fluid line has been disconnected, perform the following after installation of the power steering
components.
— Power steering fluid amount inspection
— Power steering fluid leakage inspection
— Air bleeding
Power steering fluid
ATF (M-
III or M-V, or equivalent (e.g. Dexron®II))
End Of Sie
1
2
3
4
5
acxuuw00001032
1871-1U-06B(02-10).fm 1 ページ 2006年3月15日 水曜日 午前10時58分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст