Mazda CX-9 Grand Touring. Manual — part 504
Fig. 63: Identifying DLC-2 Location
Courtesy of MAZDA MOTORS CORP.
4. Select the item name, and than select either "OFF/ON".
Items
Automatic Locks
Answer Back Buzzer
Card Key Battery Low Warning
KEYLESS RECEIVER REMOVAL/INSTALLATION
1. Disconnect the negative battery cable.
2. Remove the following parts:
1. Decoration panel (See DECORATION PANEL REMOVAL/INSTALLATION .)
2. Front console box mat (See FRONT CONSOLE BOX MAT REMOVAL/INSTALLATION .)
3. Indicator panel (See INDICATOR PANEL REMOVAL/INSTALLATION .)
4. Front console box (See FRONT CONSOLE BOX REMOVAL/INSTALLATION .)
5. Center panel (See CENTER PANEL REMOVAL/INSTALLATION .)
6. Upper column cover (See COLUMN COVER REMOVAL/INSTALLATION .)
7. Meter hood (See METER HOOD REMOVAL/INSTALLATION .)
3. Remove in the order indicated in the table.
Fig. 64: Identifying Keyless Receiver, Connector & Screw
Courtesy of MAZDA MOTORS CORP.
4. Install in the reverse order of removal.
KEYLESS RECEIVER INSPECTION [ADVANCED KEYLESS SYSTEM]
1. Measure the voltage at the auto light/wiper control module terminals as indicated below.
TERMINAL VOLTAGE TABLE (REFERENCE)
2008 Mazda CX-9 Grand Touring
2008 BODY & ACCESSORIES Security and Locks - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:47:58 AM
Page 43
© 2005 Mitchell Repair Information Company, LLC.
Fig. 65: Identifying Keyless Receiver Connector Terminals
Courtesy of MAZDA MOTORS CORP.
CONNECTOR TERMINALS REFERENCE
KEYLESS RECEIVER INSPECTION [KEYLESS ENTRY SYSTEM]
1. Measure the voltage at the auto light/wiper control module terminals as indicated below.
TERMINAL VOLTAGE TABLE (REFERENCE)
Terminal
Signal name
Connected
to
Measured condition
Voltage
(V)
Inspection item
(s)
A
Power supply
Keyless
control
module
Under any condition
B+
Keyless
control
module
Related
wiring
harnesses
C
Serial
communication
Keyless
control
module
Because this terminal is for
communication, good/no good
judgment by terminal voltage is
not possible.
-
Keyless
control
module
Related
wiring
harnesses
E
GND
Body ground Under any condition.
1.0 or
less
Related wiring
harnesses
2008 Mazda CX-9 Grand Touring
2008 BODY & ACCESSORIES Security and Locks - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:47:58 AM
Page 44
© 2005 Mitchell Repair Information Company, LLC.
Fig. 66: Identifying Keyless Receiver Connector Terminals
Courtesy of MAZDA MOTORS CORP.
CONNECTOR TERMINALS REFERENCE
KEYLESS ANTENNA REMOVAL/INSTALLATION [ADVANCED KEYLESS
SYSTEM]
EXTERIOR, LF/RF
1. Disconnect the negative battery cable.
2. Remove the inner garnish. (See INNER GARNISH REMOVAL/INSTALLATION .)
3. Remove the front door trim. (See FRONT DOOR TRIM REMOVAL/INSTALLATION .)
4. Remove the screws.
5. Disconnect the connector, then remove the keyless antenna.
6. Install in the reverse order of removal.
Terminal Signal name
Connected to
Measured condition
Voltage
(V)
Inspection item(s)
A
Power supply
BCM
Under any condition
B+
BCM
Related wiring
harnesses
B
IG1
ENG.IGA7.5
A fuse
Ignition switch is at ON
position
B+
ENG.IGA7.5
A fuse
Related wiring
harnesses
Ignition switch is at LOCK or
ACC position
1.0 or
less
D
Serial
communication
BCM
Because this terminal is for
communication, good/no good
judgment by terminal voltage
is not possible.
-
BCM
Related wiring
harnesses
E
GND
Body ground Under any condition.
1.0 or
less
Related wiring
harnesses
2008 Mazda CX-9 Grand Touring
2008 BODY & ACCESSORIES Security and Locks - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:47:58 AM
Page 45
© 2005 Mitchell Repair Information Company, LLC.
Fig. 67: Identifying Keyless Antenna & Connector With Screw (Exterior, LF/RF)
Courtesy of MAZDA MOTORS CORP.
EXTERIOR, REAR
1. Disconnect the negative battery cable.
2. Remove the screws.
3. Disconnect the connector, then remove the keyless antenna.
4. Install in the reverse order of removal.
Fig. 68: Identifying Keyless Antenna, Connector With Screw & Torque Specifications (Exterior,
Rear)
Courtesy of MAZDA MOTORS CORP.
INTERIOR, FRONT
Center
1. Disconnect the negative battery cable.
2. Remove the decoration panel. (See DECORATION PANEL REMOVAL/INSTALLATION .)
3. Remove the front console box mat. (See FRONT CONSOLE BOX MAT
REMOVAL/INSTALLATION .)
4. Remove the indicator panel. (See INDICATOR PANEL REMOVAL/INSTALLATION .)
5. Remove the front console box. (See FRONT CONSOLE BOX REMOVAL/INSTALLATION .)
2008 Mazda CX-9 Grand Touring
2008 BODY & ACCESSORIES Security and Locks - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:47:58 AM
Page 46
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст