Mazda CX-9 Grand Touring. Manual — part 11
DTC B1054, B1877, B1878, B1879, B1885 DETECTION CONDITION AND POSSIBLE CAUSE
DIAGNOSTIC PROCEDURE
DTC B1054, B1877, B1878, B1879, B1885 DIAGNOSTIC PROCEDURE
DTC
B1054 Driver-side pre-tensioner seat belt and other air bag module circuits short
B1877 Driver-side pre-tensioner seat belt circuit resistance high
B1878 Driver-side pre-tensioner seat belt circuit short to power supply
B1879 Driver-side pre-tensioner seat belt circuit short to body ground
B1885 Driver-side pre-tensioner seat belt circuit resistance low
DETECTION
CONDITION
Resistance other than 1.0-9.7 ohms detected in driver-side pre-tensioner seat belt
circuit
Malfunction in the wiring harness between driver-side pre-tensioner seat belt and SAS
control module
WARNING:
Detection conditions are for understanding the DTC outline before performing an
inspection. Performing an inspection according to only the detection conditions
may cause injury due to an operating error, or damage the system. When
performing an inspection, always follow the inspection procedure.
POSSIBLE
CAUSE
Open or short circuit in wiring harness between driver-side pre-tensioner seat belt and
SAS control module
Driver-side pre-tensioner seat belt malfunction
SAS control module malfunction
STEP
INSPECTION
ACTION
INSPECT DRIVER-SIDE PRE-TENSIONER
SEAT BELT
2008 Mazda CX-9 Grand Touring
2008 RESTRAINTS On-Board Diagnostic (Restraints) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:18:46 AM
Page 41
© 2005 Mitchell Repair Information Company, LLC.
1
Using the M-MDS, verify the following
PID/DATA monitor.
(See PID/DATA MONITOR TABLE.)
RES_PT_D
Is the resistance of the driver-side pre-tensioner
seat belt normal?
Resistance: 1.0-9.7 ohms
Yes
Replace the SAS control module. (See
SAS CONTROL MODULE
REMOVAL/INSTALLATION .)
No
Go to the next step.
2
INSPECT DRIVER-SIDE PRE-TENSIONER
SEAT BELT CONNECTOR
Turn the ignition switch to the LOCK position.
Disconnect the negative battery cable and wait
for 1 min or more.
Remove the B-pillar lower trim (LH). (See B-
PILLAR LOWER TRIM
REMOVAL/INSTALLATION .)
Disconnect the driver-side pre-tensioner seat
belt connector. (See FRONT SEAT BELT
REMOVAL/INSTALLATION .)
Is there any malfunction of the driver-side pre-
tensioner seat belt connector?
WARNING:
Handling the air bag system components
improperly can accidentally deploy the air
bag modules and pre-tensioner seat belts,
which may seriously injure you. Read the
service warnings and cautions before
handling the air bag system components.
(See AIR BAG SYSTEM SERVICE
WARNINGS .)
(See AIR BAG SYSTEM SERVICE
CAUTIONS .)
Yes Replace the air bag wiring harness.
No
Go to the next step.
VERIFY WHETHER MALFUNCTION IS IN
DRIVER-SIDE PRE-TENSIONER SEAT BELT
OR RELATED WIRING HARNESS
Connect the leads of the SST (Fuel and
thermometer checker) or apply 2-ohm resistance
to driver-side pre-tensioner seat belt connector
Yes Go to the next step.
2008 Mazda CX-9 Grand Touring
2008 RESTRAINTS On-Board Diagnostic (Restraints) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:18:46 AM
Page 42
© 2005 Mitchell Repair Information Company, LLC.
3
terminals A and B.
Set the resistance of the SST (Fuel and
thermometer checker) to the 2-ohm position.
Connect the negative battery cable.
Turn the ignition switch to the ON position.
Are DTCs B1054, B1877, B1878, B1879,
and/or B1885 indicated?
No
Replace the driver-side pre-tensioner
seat belt.
(See FRONT SEAT BELT
REMOVAL/INSTALLATION .)
4
INSPECT WIRING HARNESS BETWEEN
DRIVER-SIDE PRE-TENSIONER SEAT BELT
AND SAS CONTROL MODULE
Turn the ignition switch to the LOCK position.
Disconnect the negative battery cable and wait
for 1 min or more.
Remove the column cover. (See COLUMN
COVER REMOVAL/INSTALLATION .)
Disconnect the clock spring connector. (See
COMBINATION SWITCH
REMOVAL/INSTALLATION .)
Remove the glove compartment. (See GLOVE
COMPARTMENT
REMOVAL/INSTALLATION .)
Disconnect the passenger-side air bag module
connector. (See PASSENGER-SIDE AIR
BAG MODULE
REMOVAL/INSTALLATION .)
Disconnect the driver and passenger-side front
seat connectors. (See FRONT SEAT
REMOVAL/INSTALLATION .)
Disconnect the driver and passenger-side curtain
air bag module connectors. (See CURTAIN
AIR BAG MODULE
REMOVAL/INSTALLATION .)
Remove the B-pillar lower trim. (See B-
PILLAR LOWER TRIM
REMOVAL/INSTALLATION .)
Disconnect the driver and passenger-side pre-
tensioner seat belt connectors. (See FRONT
SEAT BELT
REMOVAL/INSTALLATION .)
Disconnect the SAS control module connectors.
(See SAS CONTROL MODULE
REMOVAL/INSTALLATION .)
Yes
Replace the SAS control module. (See
SAS CONTROL MODULE
REMOVAL/INSTALLATION .)
2008 Mazda CX-9 Grand Touring
2008 RESTRAINTS On-Board Diagnostic (Restraints) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:18:46 AM
Page 43
© 2005 Mitchell Repair Information Company, LLC.
DTC B1055, B1996, B1997, B1998, B1999
DTC B1055, B1996, B1997, B1998, B1999 DETECTION CONDITION AND POSSIBLE CAUSE
Inspect the wiring harness between SAS control
module terminal 2J and driver-side pre-tensioner
seat belt terminal A, SAS control module
terminal 2N and driver-side pre-tensioner seat
belt terminal B for the following:
Short to ground
Short to power supply
Open circuit
Is the wiring harness normal?
No
Replace the air bag wiring harness.
DTC
B1055 Passenger-side side air bag module and other air bag module circuits short
B1996 Passenger-side side air bag module circuit short to power supply
B1997 Passenger-side side air bag module circuit short to body ground
B1998 Passenger-side side air bag module circuit resistance high
B1999 Passenger-side side air bag module circuit resistance low
DETECTION
CONDITION
Resistance other than 1.0-9.7 ohms detected in passenger-side side air bag module
circuit
Malfunction in wiring harness between passenger-side side air bag module and SAS
control module
WARNING:
Detection conditions are for understanding the DTC outline before performing an
inspection. Performing an inspection according to only the detection conditions
may cause injury due to an operating error, or damage the system. When
performing an inspection, always follow the inspection procedure.
POSSIBLE
CAUSE
Open or short circuit in wiring harness between passenger-side side air bag module
and SAS control module
Passenger-side side air bag module malfunction
SAS control module malfunction
2008 Mazda CX-9 Grand Touring
2008 RESTRAINTS On-Board Diagnostic (Restraints) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:18:46 AM
Page 44
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст