Mazda CX-9 Grand Touring. Manual — part 422
17. Steering wheel (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION .)
18. Combination switch (See COMBINATION SWITCH REMOVAL/INSTALLATION .)
19. Center panel (See CENTER PANEL REMOVAL/INSTALLATION .)
20. Meter hood (See METER HOOD REMOVAL/INSTALLATION .)
21. Instrument cluster (See INSTRUMENT CLUSTER REMOVAL/INSTALLATION .)
22. Audio unit (See AUDIO UNIT REMOVAL/INSTALLATION .)
23. Steering shaft (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION .)
24. A-pillar trim (See A-PILLAR TRIM REMOVAL/INSTALLATION .)
25. Side panel (See SIDE PANEL REMOVAL/INSTALLATION .)
3. Disconnect the front door wiring harness connector (Driver side). (See FRONT DOOR MODULE
REMOVAL/INSTALLATION .)
4. Disconnect the dashboard harness connectors.
5. Remove the brake switch from the brake pedal with the brake switch connector connected. (See BRAKE
PEDAL REMOVAL/INSTALLATION .)
6. Remove the selector lever component. (See SELECTOR LEVER COMPONENT
REMOVAL/INSTALLATION .)
7. Remove the windshield wiper arm and blade. (See WINDSHIELD WIPER ARM AND BLADE
REMOVAL/INSTALLATION .)
8. Remove the cowl grille. (See COWL GRILLE REMOVAL/INSTALLATION .)
9. Remove the windshield wiper motor. (See WINDSHIELD WIPER MOTOR
REMOVAL/INSTALLATION .)
10. Remove the dashboard. (See DASHBOARD REMOVAL/INSTALLATION .)
11. Remove in the order indicated in the table.
12. Install in the reverse order of removal.
Fig. 8: Identifying Front Air Mix Actuator Remove Order - Passenger Side
Courtesy of MAZDA MOTORS CORP.
FRONT AIR MIX ACTUATOR INSPECTION
2008 Mazda CX-9 Grand Touring
2008 HVAC Control System (HVAC) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:12:35 AM
Page 6
© 2005 Mitchell Repair Information Company, LLC.
DRIVER SIDE
1. Connect battery positive voltage to front air mix actuator terminal F (or G), connect terminal G (or F) to
ground, and then verify that the front air mix actuator operates as shown in the table.
If the operation condition is not normal, replace the front air mix actuator.
FRONT AIR MIX ACTUATOR OPERATION
Fig. 9: Front Air Mix Actuator Circuit Diagram - Driver Side
Courtesy of MAZDA MOTORS CORP.
Fig. 10: Inspecting Front Air Mix Actuator - Driver Side
Courtesy of MAZDA MOTORS CORP.
2. Verify that the resistance between terminals A and E, and E and C matches the front air mix actuator
operation as shown in the graph.
If the operation condition and resistance are not normal, replace the front air mix actuator.
Terminal
Front air mix actuator operation
F
G
B+
Ground
HOT --> COLD
Ground
B+
COLD --> HOT
2008 Mazda CX-9 Grand Touring
2008 HVAC Control System (HVAC) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:12:35 AM
Page 7
© 2005 Mitchell Repair Information Company, LLC.
Fig. 11: Front Air Mix Actuator Operation Terminals A & E With E & C Resistance Graph -
Driver Side
Courtesy of MAZDA MOTORS CORP.
PASSENGER SIDE
1. Connect battery positive voltage to front air mix actuator terminal F (or G), connect terminal G (or F) to
ground, and then verify that the front air mix actuator operates as shown in the table.
If the operation condition is not normal, replace the front air mix actuator.
FRONT AIR MIX ACTUATOR OPERATION
Fig. 12: Front Air Mix Actuator Circuit Diagram - Passenger Side
Courtesy of MAZDA MOTORS CORP.
Terminal
Front air mix actuator operation
F
G
B+
Ground
COLD --> HOT
Ground
B+
HOT --> COLD
2008 Mazda CX-9 Grand Touring
2008 HVAC Control System (HVAC) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:12:35 AM
Page 8
© 2005 Mitchell Repair Information Company, LLC.
Fig. 13: Inspecting Front Air Mix Actuator - Passenger Side
Courtesy of MAZDA MOTORS CORP.
2. Verify that the resistance between terminals A and E, and E and C matches the front air mix actuator
operation as shown in the graph.
If the operation condition and resistance are not normal, replace the front air mix actuator.
Fig. 14: Front Air Mix Actuator Operation Terminals A & E With E & C Resistance Graph -
Passenger Side
Courtesy of MAZDA MOTORS CORP.
REAR AIR MIX ACTUATOR REMOVAL/INSTALLATION
1. Slide the passenger-side front seat to the maximum forward end.
2. Disconnect the negative battery cable.
3. Remove the following parts:
1. Decoration panel (See DECORATION PANEL REMOVAL/INSTALLATION .)
2. Front console box mat (See FRONT CONSOLE BOX MAT REMOVAL/INSTALLATION .)
3. Indicator panel (See INDICATOR PANEL REMOVAL/INSTALLATION .)
4. Front console box (See FRONT CONSOLE BOX REMOVAL/INSTALLATION .)
5. Dashboard under cover (See DASHBOARD UNDER COVER REMOVAL/INSTALLATION .)
6. Side wall (See SIDE WALL REMOVAL/INSTALLATION .)
7. Console panel (See CONSOLE PANEL REMOVAL/INSTALLATION .)
2008 Mazda CX-9 Grand Touring
2008 HVAC Control System (HVAC) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:12:35 AM
Page 9
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст