Mazda CX-9 Grand Touring. Manual — part 49

Fig. 57: Identifying O-Rings Of Oil Cooler Outlet Tube
Courtesy of MAZDA MOTORS CORP.

58. Using a flathead screwdriver and a hammer, pry back the crimp on the lockwashers.

59. Remove the lockwashers, washers and the counter drive gear.

CAUTION:

If the lockwasher crimp is not completely pried back, the tool
cannot fit over the bolt properly and the bolt cannot be
loosened.

Fig. 58: Prying Back Crimp On Lockwashers
Courtesy of MAZDA MOTORS CORP.

CAUTION:

Do not damage the VSS wiring harness.

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:16 AM

Page 30

© 2005 Mitchell Repair Information Company, LLC.

60. Remove the VSS and spacer from the counter drive gear.

Fig. 60: Identifying VSS And Spacer
Courtesy of MAZDA MOTORS CORP.

61. Using a flathead screwdriver, remove the snap ring.

Do not pull hard on the VSS wiring harness.

Do not damage the VSS.

Fig. 59: Identifying Bolts Of Counter Drive Gear Plate
Courtesy of MAZDA MOTORS CORP.

CAUTION:

Do not drop the sun gear.

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:16 AM

Page 31

© 2005 Mitchell Repair Information Company, LLC.

62. Remove the rear planetary gear component and the one-way clutch.

63. Remove the thrust bearing and the bearing races.

Fig. 61: Removing Snap Ring
Courtesy of MAZDA MOTORS CORP.

NOTE:

In some cases, the sun gear may be detached with the bearing race
attached.

NOTE:

Remove the sun gear in the center while holding it.

The thrust washer of the rear planetary gear on the rear side might
remain on the transaxle case side when removing the rear planetary
gear component.

Fig. 62: Removing Rear Planetary Gear Component And One-Way
Clutch
Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:16 AM

Page 32

© 2005 Mitchell Repair Information Company, LLC.

Fig. 63: Identifying Thrust Bearing And Bearing Races
Courtesy of MAZDA MOTORS CORP.

64. Using a flathead screwdriver, remove the snap ring.

Fig. 64: Removing Snap Ring
Courtesy of MAZDA MOTORS CORP.

65. Remove the retaining plates, drive and driven plates.

NOTE:

Inspect the number of drive plates and driven plates.

Fig. 65: Identifying Retaining Plates, Drive And Driven Plates
Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:16 AM

Page 33

© 2005 Mitchell Repair Information Company, LLC.

Была ли эта страница вам полезна?
Да!Нет
6 посетителей считают эту страницу полезной.
Большое спасибо!
Ваше мнение очень важно для нас.

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.

Текст

Политика конфиденциальности