Mazda CX-9 Grand Touring. Manual — part 265
DTC P0351, 0352, 0353, 0354, 0355, 0356 [MZI-3.7]
DTC P0351, 0352, 0353, 0354, 0355, 0356 (MZI-3.7) DETECTION CONDITIONS AND POSSIBLE
CAUSES
9
FOR OPEN CIRCUIT
Turn the ignition switch off.
Check continuity between the
following circuits:
CMP sensor (LH) terminal A
and PCM terminal 2AB
CMP sensor (LH) terminal B
and PCM terminal 2C
Is there continuity?
Yes Go to the next step.
No
Repair or replace suspected part, then go to Step
11.
10
INSPECT CMP SENSOR (LH)
Inspect CMP sensor (LH). (See
CRANKSHAFT POSITION (CKP)
SENSOR INSPECTION [MZI-
3.7] .)
Is there any malfunction?
Yes
Replace CMP sensor (LH), then go to the next
step. (See CRANKSHAFT POSITION (CKP)
SENSOR REMOVAL/INSTALLATION
[MZI-3.7] .)
No
Go to the next step.
11
VERIFY TROUBLESHOOTING OF
DTC P0349 COMPLETED
Verify that all disconnected
connectors reconnected.
Turn ignition switch to the ON
position (Engine off).
Clear the DTC from the PCM memory
using the M-MDS.
Start the engine.
Access the MAF PID using the M-
MDS.
Is same DTC present?
Yes
Replace the PCM, then go to the next step. (See
PCM REMOVAL/INSTALLATION [MZI-
3.7] .)
No
Go to the next step.
12
VERIFY AFTER REPAIR
PROCEDURE
Perform the "AFTER REPAIR
PROCEDURE". (See AFTER
REPAIR PROCEDURE [MZI-3.7].)
Are any DTC present?
Yes
Go to the applicable DTC inspection. (See DTC
TABLE [MZI-3.7].)
No
Troubleshooting completed.
DTC P0351
P0351: Ignition coil No.1 primary/secondary circuit
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:37 AM
Page 193
© 2005 Mitchell Repair Information Company, LLC.
DTC P0352
P0352: Ignition coil No.2 primary/secondary circuit
DTC P0353
P0353: Ignition coil No.3 primary/secondary circuit
DTC P0354
P0354: Ignition coil No.4 primary/secondary circuit
DTC P0355
P0355: Ignition coil No.5 primary/secondary circuit
DTC P0356
P0356: Ignition coil No.6 primary/secondary circuit
DETECTION
CONDITION
Each ignition primary circuit is continuously monitored. The test fails when the
PCM does not receive a valid ignition diagnostic monitor pulse signal from the
ignition module (integrated in the PCM).
POSSIBLE
CAUSE
Connector or terminal malfunction
Open circuit between ignition coil No.1 terminal C and PCM terminal 2A
Open circuit between ignition coil No.2 terminal C and PCM terminal 2F
Open circuit between ignition coil No.3 terminal C and PCM terminal 2K
Open circuit between ignition coil No.4 terminal C and PCM terminal 2W
Open circuit between ignition coil No.5 terminal C and PCM terminal 2AA
Open circuit between ignition coil No.6 terminal C and PCM terminal 2AE
Short to power supply between ignition coil No.1 terminal C and PCM terminal 2A
Short to power supply between ignition coil No.2 terminal C and PCM terminal 2F
Short to power supply between ignition coil No.3 terminal C and PCM terminal 2K
Short to power supply between ignition coil No.4 terminal C and PCM terminal 2W
Short to power supply between ignition coil No.5 terminal C and PCM terminal
2AA
Short to power supply between ignition coil No.6 terminal C and PCM terminal
2AE
Short to ground circuit between ignition coil No.1 terminal C and PCM terminal 2A
Short to ground circuit between ignition coil No.2 terminal C and PCM terminal 2F
Short to ground circuit between ignition coil No.3 terminal C and PCM terminal 2K
Short to ground circuit between ignition coil No.4 terminal C and PCM terminal 2W
Short to ground circuit between ignition coil No.5 terminal C and PCM terminal
2AA
Short to ground circuit between ignition coil No.6 terminal C and PCM terminal
2AE
Open circuit between ignition coil terminal A and main relay No.2 terminal D
Ignition coil malfunction
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:37 AM
Page 194
© 2005 Mitchell Repair Information Company, LLC.
DIAGNOSTIC PROCEDURE
DTC P0351, 0352, 0353, 0354, 0355, 0356 (MZI-3.7) DIAGNOSTIC PROCEDURE
STEP
INSPECTION
ACTION
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:37 AM
Page 195
© 2005 Mitchell Repair Information Company, LLC.
1
VERIFY FREEZE FRAME DATA HAS
BEEN RECORDED
Has FREEZE FRAME DATA been
recorded?
Yes Go to the next step.
No
Record FREEZE FRAME DATA on the repair
order, then go to the next step.
2
VERIFY RELATED REPAIR
INFORMATION AVAILABILITY
Verify related Service Bulletins and/or
on-line repair information availability.
Is any related Service Bulletins
available?
Yes
Perform repair or diagnosis according to the
available Service Bulletins.
If the vehicle is not repaired, go to the
next step.
No
Go to the next step.
3
INSPECT IGNITION COIL
CONNECTOR FOR POOR
CONNECTION
Turn the ignition switch off.
Disconnect the ignition coil connector.
Inspect for poor connection (such as
damaged/pulled-out pins, corrosion).
Are there any malfunction?
Yes
Repair or replace suspected part, then go to Step
10.
No
Go to the next step.
4
INSPECT IGNITION COIL POWER
SUPPLY CIRCUIT FOR OPEN
CIRCUIT
Disconnect the ignition coil connector.
Turn the ignition switch to the ON
position (Engine off).
Measure the voltage between ignition
coil terminal A (wiring harness-side)
and body ground.
Is the voltage B+?
Yes Go to the next step.
No
Repair or replace suspected part, then go to Step
10.
5
INSPECT IGNITION COIL SIGNAL
CIRCUIT FOR SHORT TO POWER
SUPPLY
Turn the ignition switch to the ON
position (Engine off).
Measure the voltage between ignition
coil terminal C (wiring harness-side)
and body ground.
Is the voltage B+?
Yes
Repair or replace suspected part, then go to Step
10.
No
Go to the next step.
INSPECT IGNITION COIL SIGNAL
CIRCUIT FOR SHORT TO GROUND
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:37 AM
Page 196
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст