Mazda CX-9 Grand Touring. Manual — part 268
DIAGNOSTIC PROCEDURE
DTC P0443 (MZI-3.7) DIAGNOSTIC PROCEDURE
POSSIBLE CAUSE
Purge solenoid valve malfunction
Connector or terminal malfunction
Short to ground between purge solenoid valve terminal B and PCM terminal 1 BC
Open circuit between main relay No.1 terminal D and purge solenoid valve terminal
A
Short to power supply between purge solenoid valve terminal B and PCM terminal
1 BC
Open circuit between purge solenoid valve terminal B and PCM terminal 1 BC
PCM malfunction
STEP
INSPECTION
ACTION
VERIFY FREEZE FRAME DATA
HAS BEEN RECORDED
Yes Go to the next step.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:37 AM
Page 205
© 2005 Mitchell Repair Information Company, LLC.
1
Has FREEZE FRAME DATA been
recorded?
No
Record FREEZE FRAME DATA on the repair
order, then go to the next step.
2
VERIFY RELATED REPAIR
INFORMATION AVAILABILITY
Verify related Service Bulletins
and/or on-line repair information
availability.
Is any related Service Bulletins
available?
Yes
Perform repair or diagnosis according to the
available Service Bulletins.
If the vehicle is not repaired, go to the next
step.
No
Go to the next step.
3
INSPECT PURGE SOLENOID
VALVE CONNECTOR FOR POOR
CONNECTION
Turn the ignition switch off.
Disconnect purge solenoid valve
connector.
Inspect for poor connection (such
as damaged/pulled-out pins,
corrosion).
Are there any malfunction?
Yes
Repair or replace suspected part, then go to Step
10.
No
Go to the next step.
4
INSPECT POWER SUPPLY
CIRCUIT FOR OPEN CIRCUIT
Turn the ignition switch to the ON
position (Engine off).
Measure voltage between purge
solenoid valve terminal A and body
ground.
Is voltage B+?
Yes Go to the next step.
No
Repair or replace suspected part, then go to Step
10.
5
INSPECT PURGE SOLENOID
VALVE CONTROL CIRCUIT FOR
SHORT TO POWER SUPPLY
Turn the ignition switch to the ON
position (Engine off).
Measure the voltage between purge
solenoid valve control terminal B
and body ground.
Is voltage B+?
Yes
Repair or replace suspected part, then go to Step
10.
No
Go to the next step.
INSPECT PURGE SOLENOID
VALVE CONTROL CIRCUIT FOR
SHORT TO GROUND
Yes
Repair or replace suspected part, then go to the
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:37 AM
Page 206
© 2005 Mitchell Repair Information Company, LLC.
6
Turn the ignition switch off.
Inspect for continuity between
purge solenoid valve control
terminal B and body ground.
Is there continuity?
Step 10.
No
Go to the next step.
7
INSPECT PCM CONNECTOR FOR
POOR CONNECTION
Turn the ignition switch off.
Disconnect PCM connector.
Inspect for poor connection (such
as damaged/pulled-out pins,
corrosion).
Is there any malfunction? v
Yes
Repair or replace suspected part, then go to Step
10.
No
Go to the next step.
8
INSPECT PURGE SOLENOID
VALVE CONTROL CIRCUIT FOR
OPEN CIRCUIT
Turn the ignition switch off.
Inspect continuity between purge
solenoid valve terminal B and PCM
terminal 1BC.
Is there continuity?
Yes Go to the next step.
No
Repair or replace suspected part, then go to the
Step 10.
9
INSPECT PURGE SOLENOID
VALVE
Inspect the purge solenoid valve.
(See PURGE SOLENOID
VALVE INSPECTION [MZI-
3.7] .)
Is there any malfunction?
Yes
Replace purge solenoid valve (See PURGE
SOLENOID VALVE
REMOVAL/INSTALLATION [MZI-3.7] .), then
go to Step 10.
No
Go to the next step.
10
VERIFY TROUBLESHOOTING OF
DTC P0443 COMPLETED
Make sure to reconnect all
disconnected connectors.
Clear DTC from PCM memory
using M-MDS.
Perform the "KOEO or KOER self-
test" using the M-MDS. (See
KOEO/KOER SELF TEST
[MZI-3.7].)
Is the PENDING CODE same DTC
Yes
Replace PCM, then go to the next step. (See PCM
REMOVAL/INSTALLATION [MZI-3.7] .)
No
Go to the next step.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:38 AM
Page 207
© 2005 Mitchell Repair Information Company, LLC.
DTC P0446 [MZI-3.7]
DTC P0446 (MZI-3.7) DETECTION CONDITIONS AND POSSIBLE CAUSES
present?
11
VERIFY AFTER REPAIR
PROCEDURE
Perform the "AFTER REPAIR
PROCEDURE". (See AFTER
REPAIR PROCEDURE [MZI-
3.7].)
Are any DTCs present?
Yes
Go to the applicable DTC inspection. (See DTC
TABLE [MZI-3.7].)
No
Troubleshooting completed.
DTC P0446
CV solenoid valve control circuit
DETECTION
CONDITION
Monitors the CV solenoid valve circuit for an electrical failure. The test fails when
the signal moves outside the minimum or maximum allowable calibrated parameters
for a specified canister vent duty cycle by PCM command.
POSSIBLE
CAUSE
CV solenoid valve malfunction
Connector or terminal malfunction
Short to ground between CV solenoid valve terminal B and PCM terminal 1Z
Open circuit between battery and CV solenoid valve terminal A
Short to power supply between CV solenoid valve terminal B and PCM terminal 1Z
Open circuit between CV solenoid valve terminal B and PCM terminal 1Z
PCM malfunction
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:38 AM
Page 208
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст