Mazda CX-9 Grand Touring. Manual — part 247
3
INSPECT FUEL INJECTOR NO.2 CONNECTOR
FOR POOR CONNECTION
Turn the ignition switch off.
Disconnect the fuel injector No.2 connector.
Inspect for poor connection (such as
damaged/pulled-out pins, corrosion).
Are there malfunction?
Yes
Repair or replace suspected part,
then go to Step 8.
No
Go to the next step.
4
INSPECT PCM CONNECTOR FOR POOR
CONNECTION
Turn the ignition switch off.
Disconnect the PCM connector.
Inspect for poor connection (such as
damaged/pulled-out pins, corrosion).
Is there malfunction?
Yes
Repair or replace suspected part,
then go to Step 8.
No
Go to the next step.
5
INSPECT FUEL INJECTOR NO.2 POWER SUPPLY
CIRCUIT FOR OPEN CIRCUIT
Turn the ignition switch to the ON position (Engine
off).
Measure the voltage between fuel injector No.2
connector terminal B and body ground.
Is the voltage B+?
Yes Go to the next step.
No
Repair or replace suspected part,
then go to Step 8.
6
INSPECT FUEL INJECTOR NO.2 SIGNAL
CIRCUIT FOR OPEN CIRCUIT
Inspect continuity between fuel injector No.2
terminal A (wiring harness-side) and PCM terminal
2BM (wiring harness-side).
Is there continuity?
Yes Go to the next step.
No
Repair or replace suspected part,
then go to Step 8.
7
INSPECT FUEL INJECTOR NO.2
Inspect the fuel injector No.2. (See FUEL
INJECTOR INSPECTION [MZI-3.7] .)
Is there any malfunction?
Yes
Replace the fuel injector No.2, then
go to the next step.
No
Go to the next step.
8
VERIFY TROUBLESHOOTING OF DTC P0202
HAS BEEN COMPLETED
Verify that all disconnected connectors reconnected.
Clear DTC from memory using M-MDS.
Start the engine.
Perform the "KOEO/KOER self-test" (See
Yes
Replace the PCM, then go to the
next step.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:36 AM
Page 121
© 2005 Mitchell Repair Information Company, LLC.
DTC P0203 [MZI-3.7]
DTC P0203 (MZI-3.7) DETECTION CONDITIONS AND POSSIBLE CAUSES
KOEO/KOER SELF TEST [MZI-3.7].)
Is same DTC present?
No
Go to the next step.
9
VERIFY AFTER REPAIR PROCEDURE
Perform the "AFTER REPAIR PROCEDURE".
(See AFTER REPAIR PROCEDURE [MZI-
3.7].)
Are any DTCs present?
Yes
Go to the applicable DTC
inspection. (See DTC TABLE
[MZI-3.7].)
No
Troubleshooting completed.
DTC P0203
Injector circuit/open-cylinder No.3
DETECTION
CONDITION
The CCM monitors the operation of the fuel injector drivers in the PCM. The test
fails if the fuel injector circuitry is inoperative.
POSSIBLE CAUSE
Fuel injector No.3 malfunction
Connector or terminal malfunction
Open circuit between fuel pump relay and fuel injector No.3 terminal B
Open circuit between fuel injector No.3 terminal A and PCM terminal 2BF
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:36 AM
Page 122
© 2005 Mitchell Repair Information Company, LLC.
DIAGNOSTIC PROCEDURE
DTC P0203 (MZI-3.7) DIAGNOSTIC PROCEDURE
STEP
INSPECTION
ACTION
1
VERIFY FREEZE FRAME DATA HAS BEEN
RECORDED
Has FREEZE FRAME DATA been recorded?
Yes Go to the next step.
No
Record FREEZE FRAME DATA
on the repair order, then go to the
next step.
2
VERIFY RELATED REPAIR INFORMATION
AVAILABILITY
Verify related Service Bulletins availability.
Is any related Service Bulletins available?
Yes
Perform repair or diagnosis
according to available Service
Bulletins.
If vehicle is not repaired, go
to the next step.
No
Go to the next step.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:36 AM
Page 123
© 2005 Mitchell Repair Information Company, LLC.
3
INSPECT FUEL INJECTOR NO.3 CONNECTOR
FOR POOR CONNECTION
Turn the ignition switch off.
Disconnect the fuel injector No.3 connector.
Inspect for poor connection (such as
damaged/pulled-out pins, corrosion).
Are there malfunction?
Yes
Repair or replace suspected part,
then go to Step 8.
No
Go to the next step.
4
INSPECT PCM CONNECTOR FOR POOR
CONNECTION
Turn the ignition switch off.
Disconnect the PCM connector.
Inspect for poor connection (such as
damaged/pulled-out pins, corrosion).
Is there malfunction?
Yes
Repair or replace suspected part,
then go to Step 8.
No
Go to the next step.
5
INSPECT FUEL INJECTOR NO.3 POWER SUPPLY
CIRCUIT FOR OPEN CIRCUIT
Turn the ignition switch to the ON position (Engine
off).
Measure the voltage between fuel injector No.3
connector terminal B and body ground.
Is the voltage B+?
Yes Go to the next step.
No
Repair or replace suspected part,
then go to Step 8.
6
INSPECT FUEL INJECTOR NO.3 SIGNAL
CIRCUIT FOR OPEN CIRCUIT
Inspect continuity between fuel injector No.3
terminal A (wiring harness-side) and PCM terminal
2BF (wiring harness-side).
Is there continuity?
Yes Go to the next step.
No
Repair or replace suspected part,
then go to Step 8.
7
INSPECT FUEL INJECTOR NO.3
Inspect the fuel injector No.3. (See FUEL
INJECTOR INSPECTION [MZI-3.7] .)
Is there any malfunction?
Yes
Replace the fuel injector No.3, then
go to the next step.
No
Go to the next step.
8
VERIFY TROUBLESHOOTING OF DTC P0203
HAS BEEN COMPLETED
Verify that all disconnected connectors
reconnected.
Clear DTC from memory using M-MDS.
Start the engine.
Yes
Replace the PCM, then go to the
next step.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:36 AM
Page 124
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст