Mazda CX-9 Grand Touring. Manual — part 114
Fig. 20: Identifying Rear Bumper Components & Torque Specifications
Courtesy of MAZDA MOTORS CORP.
REFLECTOR REMOVAL NOTE
1. Pull off the reflector from the rear bumper in the direction and in the order as shown by the arrows.
Fig. 21: Identifying Rear Bumper And Reflector
Courtesy of MAZDA MOTORS CORP.
REAR OVER FENDER LOWER ASSEMBLY NOTE
1. Attach the rear over fender lower to the rear bumper fascia with nuts.
2. Use a soldering copper and thermally deform the tab in order to fasten the stiffening rib.
2008 Mazda CX-9 Grand Touring
2008 ACCESSORIES & BODY, CAB Body Panels - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:44:45 AM
Page 14
© 2005 Mitchell Repair Information Company, LLC.
Fig. 22: Identifying Rear Over Fender Lower And Rear Bumper Fascia With Nuts
Courtesy of MAZDA MOTORS CORP.
FRONT FENDER PANEL REMOVAL/INSTALLATION
1. Disconnect the negative battery cable.
2. Remove the following parts:
1. Windshield wiper arm and blade (See WINDSHIELD WIPER ARM AND BLADE
REMOVAL/INSTALLATION )
2. Side cowl grille (See COWL GRILLE REMOVAL/INSTALLATION )
3. Front over fender (See OVER FENDER REMOVAL/INSTALLATION )
4. Front bumper (See FRONT BUMPER REMOVAL/INSTALLATION)
5. Front combination lights (See FRONT COMBINATION LIGHT
REMOVAL/INSTALLATION )
6. Sail garnish (See SAIL GARNISH REMOVAL/INSTALLATION ) '
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
Fig. 23: Identifying Removing Sequence Of Front Fender Panel Components & Torque
Specifications
Courtesy of MAZDA MOTORS CORP.
2008 Mazda CX-9 Grand Touring
2008 ACCESSORIES & BODY, CAB Body Panels - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:44:45 AM
Page 15
© 2005 Mitchell Repair Information Company, LLC.
SHROUD PANEL REMOVAL/INSTALLATION
1. Disconnect the negative battery cable.
2. Remove the following parts:
1. Front bumper (See FRONT BUMPER REMOVAL/INSTALLATION)
2. Front combination lights (See FRONT COMBINATION LIGHT
REMOVAL/INSTALLATION )
3. Front bumper reinforcement (See FRONT BUMPER REINFORCEMENT
REMOVAL/INSTALLATION)
4. Ambient temperature sensor (See AMBIENT TEMPERATURE SENSOR
REMOVAL/INSTALLATION )
5. Crash zone sensor (See CRASH ZONE SENSOR REMOVAL/INSTALLATION )
6. Hood latch (See HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION )
3. Put the oil cooler aside.
4. Remove the front crossmember extension. (See FRONT CROSSMEMBER
REMOVAL/INSTALLATION .)
5. Remove in the order indicated in the table.
6. Install in the reverse order of removal.
Fig. 24: Identifying Removing Sequence Of Shroud Panel Components & Torque Specifications
Courtesy of MAZDA MOTORS CORP.
UPPER MOUNT RUBBER BRACKET REMOVAL NOTE
1. Remove the upper mount rubber bracket while pressing down the upper mount rubber bracket tab in the
direction of the arrow.
2008 Mazda CX-9 Grand Touring
2008 ACCESSORIES & BODY, CAB Body Panels - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:44:45 AM
Page 16
© 2005 Mitchell Repair Information Company, LLC.
Fig. 25: Identifying Upper Mount Rubber Bracket
Courtesy of MAZDA MOTORS CORP.
COWL PANEL REMOVAL/INSTALLATION
1. Disconnect the negative battery cable.
2. Remove the following parts:
1. Windshield wiper arm and blade (See WINDSHIELD WIPER ARM AND BLADE
REMOVAL/INSTALLATION )
2. Cowl grille (See COWL GRILLE REMOVAL/INSTALLATION )
3. Windshield wiper motor (See WINDSHIELD WIPER MOTOR
REMOVAL/INSTALLATION )
3. Remove the bolts, then remove the cowl panel.
4. Install in the reverse order of removal.
Fig. 26: Identifying Cowl Panel With Nuts, Bolts & Torque Specifications
Courtesy of MAZDA MOTORS CORP.
2008 Mazda CX-9 Grand Touring
2008 ACCESSORIES & BODY, CAB Body Panels - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:44:45 AM
Page 17
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст