Mazda CX-9 Grand Touring. Manual — part 286
DTC P061C [MZI-3.7]
DTC P061C (MZI-3.7) DETECTION CONDITIONS AND POSSIBLE CAUSES
3
ON position (Engine off).
Verify related pending code or stored
DTCs.
Are other DTCs present?
No
Go to the next step.
4
INSPECT FOR CORRECT PCM
OPERATION
Disconnect all the PCM connectors.
Visually inspect for:
Pushed out pins
Corrosion
Connect all the PCM connectors and
verify that they seat correctly.
Retrieve DTCs using the M-MDS.
Is the PENDING CODE for this DTC
present?
Yes
Replace the PCM, then go to the next step. (See
PCM REMOVAL/INSTALLATION [MZI-
3.7] .)
No
Go to the next step.
5
VERIFY TROUBLESHOOTING OF
DTC P061F HAS BEEN COMPLETED
Verify that all disconnected
connectors are reconnected.
Turn the ignition switch to the ON
position (Engine off).
Clear the DTC from the PCM memory
using the M-MDS.
Perform the KOEO and KOER self-
test.
Retrieve DTCs using the M-MDS.
Is the PENDING CODE for this DTC
present?
Yes
Replace the PCM, then go to the next step. (See
PCM REMOVAL/INSTALLATION [MZI-
3.7] .)
No
Go to the next step.
6
VERIFY AFTER REPAIR
PROCEDURE
Perform the "AFTER REPAIR
PROCEDURE". (See AFTER
REPAIR PROCEDURE [MZI-3.7].)
Are any DTC present?
Yes
Go to the applicable DTC inspection. (See DTC
TABLE [MZI-3.7].)
No
Troubleshooting completed.
DTC P061C
Internal control module engine RPM performance
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:39 AM
Page 277
© 2005 Mitchell Repair Information Company, LLC.
DIAGNOSTIC PROCEDURE
DTC P061C (MZI-3.7) DIAGNOSTIC PROCEDURE
DETECTION CONDITION
Indicates that a calculation error occurred in the PCM.
POSSIBLE CAUSE
CKP sensor circuit is open or short.
CKP sensor circuit intermittent
CKP sensor malfunction
CMP sensor circuit is open or short.
CMP sensor circuit intermittent
CMP sensor malfunction
PCM malfunction
STEP
INSPECTION
ACTION
1
VERIFY FREEZE FRAME DATA HAS
BEEN RECORDED
Has FREEZE FRAME DATA been
recorded?
Yes Go to the next step.
No
Record FREEZE FRAME DATA on the repair
order, then go to the next step.
2
VERIFY RELATED REPAIR
INFORMATION AVAILABILITY
Verify related Service Bulletins and/or
on-line repair information availability.
Is any related Service Bulletins
available?
Yes
Perform repair or diagnosis according to the
available Service Bulletins.
If the vehicle is not repaired, go to the
next step.
No
Go to the next step.
3
VERIFY RELATED PENDING CODE
OR STORED DTCs
Turn the ignition switch off then to the
ON position (Engine off).
Verify related pending code or stored
DTCs.
Are other DTCs present?
Yes
Go to the appropriate DTC troubleshooting. (See
DTC TABLE [MZI-3.7].)
No
Go to the next step.
4
INSPECT CKP SENSOR SIGNAL SENT
TO PCM
NOTE:
The battery should be fully charged
and the starting system should be
functioning properly.
Yes Go to the next step.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:39 AM
Page 278
© 2005 Mitchell Repair Information Company, LLC.
Disable the inertia switch.
Turn the ignition switch to the ON
position (Engine off)
Access the PCM and monitor the RPM
PID.
Crank the engine.
Is the RPM greater than 150 rpm?
No
Inspect the CKP sensor or related harness.
Repair or replace suspected part, then go to the
next step.
5
INSPECT FOR CORRECT PCM
OPERATION
Disconnect all the PCM connectors.
Visually inspect for:
Pushed out pins
Corrosion
Connect all the PCM connectors and
verify that they seat correctly.
Retrieve DTCs using the M-MDS.
Is the PENDING CODE for this DTC
present?
Yes
Replace the PCM, then go to the next step. (See
PCM REMOVAL/INSTALLATION [MZI-
3.7] .)
No
Go to the next step.
6
VERIFY TROUBLESHOOTING OF
DTC P061C HAS BEEN COMPLETED
Verify that all disconnected
connectors are reconnected.
Turn the ignition switch to the ON
position (Engine off).
Clear the DTC from the PCM memory
using the M-MDS.
Perform the "KOEO and KOER self-
test". (See KOEO/KOER SELF
TEST [MZI-3.7].)
Retrieve the DTCs using the M-MDS.
Is the PENDING CODE for this DTC
present?
Yes
Replace the PCM, then go to the next step. (See
PCM REMOVAL/INSTALLATION [MZI-
3.7] .)
No
Go to the next step.
7
VERIFY AFTER REPAIR
PROCEDURE
Perform the "AFTER REPAIR
PROCEDURE". (See AFTER
REPAIR PROCEDURE [MZI-3.7].)
Are any DTCs present?
Yes
Go to the applicable DTC inspection. (See DTC
TABLE [MZI-3.7].)
No
Troubleshooting completed.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:39 AM
Page 279
© 2005 Mitchell Repair Information Company, LLC.
DTC P0620 [MZI-3.7]
DTC P0620 (MZI-3.7) DETECTION CONDITIONS AND POSSIBLE CAUSES
DTC P0620
Generator control circuit
DETECTION
CONDITION
The PCM reads the generator and sends a DTC through the network when the
generator indicates a concern.
POSSIBLE CAUSE
Drive belt misadjustment
Generator malfunction
Open circuit between generator terminal LI and PCM terminal 2AG
Open circuit between generator terminal B and battery positive terminal
Short to ground between generator terminal LI and PCM terminal 2AG
Short to power supply between generator terminal LI and PCM terminal 2AG
Connector or terminal malfunction
PCM malfunction
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:39 AM
Page 280
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст