Mazda CX-9 Grand Touring. Manual — part 127
Fig. 5: Symptom Troubleshooting Chart
Courtesy of MAZDA MOTORS CORP.
NO.1 ANY OF THE FOLLOWING LIGHTS DO NOT ILLUMINATE WHEN
IGNITION SWITCH TURNED TO ON POSITION: (ABS WARNING LIGHT,
BRAKE SYSTEM WARNING LIGHT, DSC INDICATOR LIGHT AND/OR TCS
OFF LIGHT) [DSC/RSC]
TROUBLESHOOTING CHART
DIAGNOSTIC PROCEDURE
DIAGNOSTIC PROCEDURE
1
Any of the following lights do not illuminate when the ignition switch is turned to the ON
position: (ABS warning light, BRAKE system warning light, DSC indicator light and/or TCS
OFF light).
[TROUBLESHOOTING HINTS]
Inspect each light in the instrument cluster for malfunction
Poor connection at DSC/RSC HU/CM connector
STEP
INSPECTION
ACTION
1
INSPECT FOR DTCS IN DSC/RSC
HU/CM
Inspect the DTC for the ON-BOARD
DIAGNOSTIC SYSTEM.
Have DTCs been stored in memory?
Yes
Perform the applicable DTC inspection. (See
ON-BOARD DIAGNOSIS [DSC/RSC] .)
No
Go to the next step.
2
INSPECT WHETHER MALFUNCTION
IS IN INSTRUMENT CLUSTER
SYSTEM OR OTHER SYSTEM
Do other warning and indicator lights
illuminate when the ignition switch is
turned to the ON position?
Yes Go to the next step.
No
Inspect or repair the instrument cluster (power
supply system, ground system).
2008 Mazda CX-9 Grand Touring
2008 BRAKES Symptom Troubleshooting (DSC/RSC) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 9:41:34 AM
Page 7
© 2005 Mitchell Repair Information Company, LLC.
NO.2 ANY OF THE FOLLOWING LIGHTS REMAIN ON: (ABS WARNING
LIGHT, BRAKE SYSTEM WARNING LIGHT, DSC INDICATOR LIGHT AND/OR
TCS OFF LIGHT) [DSC/RSC]
TROUBLESHOOTING CHART
3
VERIFY THAT DSC/RSC HU/CM
CONNECTOR IS CONNECTED
Is the DSC/RSC HU/CM securely
connected?
Yes Go to the next step.
No
Connect the DSC/RSC HU/CM connector
securely, then go to the next step.
4
VERIFY THAT DSC/RSC HU/CM
CONNECTOR TERMINAL OR
RELATED CONNECTOR TERMINALS
ARE CONNECTED
Are DSC/RSC HU/CM connector
terminal, instrument cluster connector
terminal, or related connector terminals
securely connected?
Yes Go to the next step.
No
Securely connect the DSC/RSC HU/CM
connector terminal and related connector
terminals.
5
INSPECT INSTRUMENT CLUSTER
Inspect the instrument cluster. (See
ON-BOARD DIAGNOSIS
[DSC/RSC] .)
If the instrument cluster normal
Yes
Replace the DSC/RSC HU/CM. (see DSC/RSC
HU/CM REMOVAL/INSTALLATION .)
No
Replace the instrument cluster. (See
INSTRUMENT CLUSTER
REMOVAL/INSTALLATION .)
2
Any of the following lights remain on: (ABS warning light, BRAKE system warning light, DSC
indicator light and/or TCS OFF light)
[TROUBLESHOOTING HINTS]
Brake fluid amount is low
Parking brake does not release
No connection at DSC/RSC HU/CM connector
(When HU/CM connector is disconnected, ABS warning light and BRAKE system warning light
illuminate)
DSC/RSC HU/CM detected malfunction (Input and output device malfunction)
DSC/RSC HU/CM detects low voltage in power supply
DSC/RSC HU/CM ground malfunction
(When DSC/RSC HU/CM ground is not securely connected, ABS warning light and BRAKE
system warning light illuminate but diagnostic trouble code does not displayed)
2008 Mazda CX-9 Grand Touring
2008 BRAKES Symptom Troubleshooting (DSC/RSC) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 9:41:34 AM
Page 8
© 2005 Mitchell Repair Information Company, LLC.
DIAGNOSTIC PROCEDURE
DIAGNOSTIC PROCEDURE
DSC/RSC HU/CM does not operate (DSC/RSC HU/CM malfunction)
STEP
INSPECTION
ACTION
1
INSPECT BRAKE FLUID AMOUNT AND
VERIFY THAT PARKING BRAKE
RELEASES
Is the brake fluid amount normal?
Is the parking brake pedal released?
Yes Go to the next step.
No
Add brake fluid or release parking brake
pedal.
2
INSPECT DTCS IN INSTRUMENT
CLUSTER
Inspect the DTC for the instrument
cluster ON-BOARD DIAGNOSTIC
SYSTEM.
Has DTC U2064 been recorded in
memory?
Yes Go to the next step.
No
Inspect the instrument cluster. (See
INSTRUMENT CLUSTER
INSPECTION .)
3
INSPECT DTCS IN DSC/RSC HU/CM
Inspect the DTC for the ON-BOARD
DIAGNOSTIC SYSTEM.
Have DTCs been stored in memory?
Yes
Perform inspection using appropriate DTC.
(See ON-BOARD DIAGNOSIS
[DSC/RSC] .)
No
Go to the next step.
4
INSPECT WHETHER MALFUNCTION
IS IN CONTROL MODULE
CONNECTOR, TERMINAL OR OTHER
Do the ABS warning light and BRAKE
system warning light go out after 4 s
when the ignition switch is turned to the
ON position?
Yes
Temporary poor connection in control module
connector.
Inspect DSC/RSC HU/CM connector, then go
to Step 7.
Inspect DSC/RSC HU/CM connector terminal,
then go to Step 8.
No
Go to the next step.
5
INSPECT BATTERY
Is the battery voltage normal?
Yes Go to the next step.
No
Inspect the battery and charging system.
(See BATTERY INSPECTION [MZI-3.7] .)
(See GENERATOR INSPECTION [MZI-
3.7] .)
6
INSPECT CHARGING SYSTEM
Is the battery voltage normal with
electrical load (A/C, headlight, etc.) on
and engine idling?
Yes Go to the next step.
No
Inspect the charging system (drive belt
tension, generator, etc.).
(See GENERATOR INSPECTION [MZI-
3.7] .)
VERIFY THAT DSC/RSC HU/CM
Yes Go to the next step.
2008 Mazda CX-9 Grand Touring
2008 BRAKES Symptom Troubleshooting (DSC/RSC) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 9:41:34 AM
Page 9
© 2005 Mitchell Repair Information Company, LLC.
NO.3 THERE IS A MALFUNCTION IN THE SYSTEM EVEN THOUGH ABS
WARNING LIGHT, BRAKE SYSTEM WARNING LIGHT, DSC INDICATOR
LIGHT AND TCS OFF LIGHT DO NOT ILLUMINATE [DSC/RSC]
TROUBLESHOOTING CHART
DIAGNOSTIC PROCEDURE
DIAGNOSTIC PROCEDURE
NO.4 ABS OR TCS OPERATES FREQUENTLY/TCS DOES NOT WORK
CORRECTLY [DSC/RSC]
TROUBLESHOOTING CHART
7
CONNECTOR IS CONNECTED
Is the DSC/RSC HU/CM securely
connected?
No
Connect the DSC/RSC HU/CM connector
securely, then go to the next step.
8
VERIFY THAT DSC/RSC HU/CM
CONNECTOR TERMINAL OR
RELATED CONNECTOR TERMINALS
ARE CONNECTED
Are the DSC/RSC HU/CM connector
terminal or instrument cluster connector
terminal etc. related connector terminals
securely connected?
Yes
Replace the DSC/RSC HU/CM. (See
DSC/RSC HU/CM
REMOVAL/INSTALLATION .)
No
Securely connect the DSC/RSC HU/CM
connector terminal and related connector
terminals.
3
There is a malfunction in the system even though the ABS warning light, BRAKE system warning
light, DSC indicator light and TCS OFF light do not illuminate.
[TROUBLESHOOTING HINTS]
There is a mechanical malfunction in system
STEP
INSPECTION
ACTION
1
INSPECT DSC/RSC HU/CM FOR DTCs
Inspect the DTC for the ON-BOARD DIAGNOSTIC
SYSTEM.
Have DTCs been stored in memory?
Yes
Perform the applicable DTC
inspection.
(See ON-BOARD DIAGNOSIS
[DSC/RSC] .)
No
Go to the next step.
2
INSPECT DSC/RSC SYSTEM
Perform DSC/RSC system inspection. (See
DSC/RSC SYSTEM INSPECTION .)
Is the system normal?
Yes
Inspect the conventional brake
system.
No
Repair or replace any
malfunctioning part.
2008 Mazda CX-9 Grand Touring
2008 BRAKES Symptom Troubleshooting (DSC/RSC) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 9:41:34 AM
Page 10
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст