Mazda CX-9 Grand Touring. Manual — part 89
Fig. 23: Identifying Oil Cooler & Oil Pipe
Courtesy of MAZDA MOTORS CORP.
8. Connect the input/turbine speed sensor terminal 2 to the battery positive terminal, connect the battery
negative terminal to input/turbine speed sensor terminal 1 through an ammeter set to a resistance of 100
ohm.
Fig. 24: Connecting Input/Turbine Speed Sensor Terminal 2 To Battery Positive Terminal
Courtesy of MAZDA MOTORS CORP.
9. Measure the current while waving a magnet back and forth over the top of the input/turbine speed sensor
(less than 5 mm {0.197 in}).
If there is any malfunction, replace the input/turbine speed sensor. (See INPUT/TURBINE
SPEED SENSOR REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL].)
Input/turbine speed sensor
SIGNAL REFERENCE
10. Install the input/turbine speed sensor. (See INPUT/TURBINE SPEED SENSOR
REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL].)
11. Install the control valve body. (See CONTROL VALVE BODY REMOVAL/INSTALLATION
Signal Current (mA)
High
12.0-16.0
Low
4.0-8.0
2008 Mazda CX-9 Grand Touring
2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:29:30 AM
Page 25
© 2005 Mitchell Repair Information Company, LLC.
[AW6A-EL, AW6AX-EL].)
Fig. 25: Measuring Current Of Input/Turbine Speed Sensor
Courtesy of MAZDA MOTORS CORP.
12. Install the oil pipe. (See OIL COOLER REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL].)
13. Install the oil cooler. (See OIL COOLER REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL].)
14. Add ATF to the specified level. (See AUTOMATIC TRANSAXLE FLUID (ATF) REPLACEMENT
[AW6A-EL, AW6AX-EL].)
15. Install the air cleaner component. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-
3.7] .)
16. Connect the negative battery cable.
17. Perform the mechanical system test. (See MECHANICAL SYSTEM TEST [AW6A-EL, AW6AX-
EL].)
INPUT/TURBINE SPEED SENSOR REMOVAL/INSTALLATION [AW6A-EL,
AW6AX-EL]
1. Disconnect the negative battery cable.
2. Remove the air cleaner component. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION
[MZI-3.7] .)
3. Drain the ATF. (See AUTOMATIC TRANSAXLE FLUID (ATF) REPLACEMENT [AW6A-EL,
AW6AX-EL].)
4. Remove the oil cooler.
5. Remove the oil pipe. (See OIL COOLER REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL].)
WARNING:
A hot transaxle and ATF can cause severe burns. Turn off the engine
and wait until then are cool before replacing the ATF.
2008 Mazda CX-9 Grand Touring
2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:29:30 AM
Page 26
© 2005 Mitchell Repair Information Company, LLC.
6. Remove the control valve body. (See CONTROL VALVE BODY REMOVAL/INSTALLATION
[AW6A-EL, AW6AX-EL].)
7. Remove the input/turbine speed sensor.
8. Install the input/turbine speed sensor.
Tightening torque
3.9-6.9 N.m {40-70 kgf.cm, 26-60 in.lbf}
9. Install the control valve body. (See CONTROL VALVE BODY REMOVAL/INSTALLATION
[AW6A-EL, AW6AX-EL].)
10. Install the oil pipe. (See OIL COOLER REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL].)
11. Install the oil cooler. (See OIL COOLER REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL].)
Fig. 27: Locating Input/Turbine Speed Sensor
Courtesy of MAZDA MOTORS CORP.
12. Add ATF to the specified level. (See AUTOMATIC TRANSAXLE FLUID (ATF) REPLACEMENT
CAUTION:
Do not damage the input/turbine speed sensor.
Fig. 26: Identifying Oil Cooler & Oil Pipe
Courtesy of MAZDA MOTORS CORP.
2008 Mazda CX-9 Grand Touring
2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:29:30 AM
Page 27
© 2005 Mitchell Repair Information Company, LLC.
[AW6A-EL, AW6AX-EL].)
13. Install the air cleaner component. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-
3.7] .)
14. Connect the negative battery cable.
15. Perform the mechanical system test. (See MECHANICAL SYSTEM TEST [AW6A-EL, AW6AX-
EL].)
VEHICLE SPEED SENSOR (VSS) INSPECTION [AW6A-EL, AW6AX-EL]
ON-VEHICLE INSPECTION
1. Disconnect the negative battery cable.
2. Remove the air cleaner component. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION
[MZI-3.7] .)
3. Remove the TCM. (See TCM REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL].)
4. Verify that there is no continuity between the coupler component terminals B19 and GND or B20 and
GND.
Fig. 28: Identifying Coupler Component
Courtesy of MAZDA MOTORS CORP.
If there is any malfunction, inspect the coupler component.
If the coupler component is normal, replace the ATX. (See AUTOMATIC TRANSAXLE
REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL].)
CAUTION:
Water or foreign material entering the connector can cause a poor
connection or corrosion. Be sure not to allow water or foreign
material on the connector when disconnecting.
Do not damage the terminals.
NOTE:
Inspect with a tester that can indicate more than 10 megohms
and confirm that the value is more than 1 megohm.
2008 Mazda CX-9 Grand Touring
2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:29:30 AM
Page 28
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст