Mazda CX-9 Grand Touring. Manual — part 283
DTC P0604 [MZI-3.7]
DTC P0604 (MZI-3.7) DETECTION CONDITIONS AND POSSIBLE CAUSES
DIAGNOSTIC PROCEDURE
DTC P0604 (MZI-3.7) DIAGNOSTIC PROCEDURE
Retrieve DTCs using the M-MDS.
Is the PENDING CODE for this DTC
present?
7
VERIFY TROUBLESHOOTING OF DTC
P0603 HAS BEEN COMPLETED
Verify that all disconnected connectors
are reconnected.
Turn the ignition switch to the ON
position (Engine off).
Clear the DTC from the PCM memory
using the M-MDS.
Perform the "KOEO and KOER self-
test". (See KOEO/KOER SELF TEST
[MZI-3.7].)
Retrieve DTCs using the M-MDS.
Is the PENDING CODE for this DTC
present?
Yes
Replace the PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION
[MZI-3.7] .)
No
Go to the next step.
8
VERIFY AFTER REPAIR PROCEDURE
Perform the "AFTER REPAIR
PRECAUTION". (See AFTER
REPAIR PROCEDURE [MZI-3.7].)
Are any DTCs present?
Yes
Go to the applicable DTC inspection. (See
DTC TABLE [MZI-3.7].)
No
Troubleshooting completed.
DTC P0604
Internal control module random access memory (RAM) error
DETECTION CONDITION
Indicates the PCM RAM has been corrupted.
POSSIBLE CAUSE
Module reprogramming
Aftermarket performance products.
PCM malfunction
STEP
INSPECTION
ACTION
1
VERIFY FREEZE FRAME DATA HAS
BEEN RECORDED
Has FREEZE FRAME DATA been
Yes Go to the next step.
No
Record FREEZE FRAME DATA on the repair
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:39 AM
Page 265
© 2005 Mitchell Repair Information Company, LLC.
DTC P0605 [MZI-3.7]
DTC P0605 (MZI-3.7) DETECTION CONDITIONS AND POSSIBLE CAUSES
DIAGNOSTIC PROCEDURE
recorded?
order, then go to the next step.
2
VERIFY RELATED REPAIR
INFORMATION AVAILABILITY
Verify related Service Bulletins
and/or on-line repair information
availability.
Is any related Service Bulletins
available?
Yes
Perform repair or diagnosis according to the
available Service Bulletins.
If the vehicle is not repaired, go to the next
step.
No
Perform PCM reprograming using the M-MDS,
then go to next step.
3
VERIFY TROUBLESHOOTING OF
P0604 HAS BEEN COMPLETED
Verify that all disconnected
connectors are reconnected.
Turn the ignition switch to the ON
position (Engine off).
Clear the DTC from the PCM
memory using the M-MDS.
Perform the "KOEO and KOER self-
test". (See KOEO/KOER SELF
TEST [MZI-3.7].)
Retrieve DTCs using the M-MDS.
Is the PENDING CODE for this DTC
present?
Yes
Replace the PCM, go to the next step. (See PCM
REMOVAL/INSTALLATION [MZI-3.7] .)
No
Go to the next step.
4
VERIFY AFTER REPAIR
PROCEDURE
Perform the "After Repair Procedure".
(See AFTER REPAIR
PROCEDURE [MZI-3.7].)
Are any DTCs present?
Yes
Go to the applicable DTC inspection. (See DTC
TABLE [MZI-3.7].)
No
Troubleshooting completed.
DTC P0605
PCM read only memory (ROM) error
DETECTION CONDITION
The PCM ROM has been corrupted.
POSSIBLE CAUSE
An attempt was made to change the calibration
Module programming error
PCM malfunction
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:39 AM
Page 266
© 2005 Mitchell Repair Information Company, LLC.
DTC P0605 (MZI-3.7) DIAGNOSTIC PROCEDURE
DTC P0606 [MZI-3.7]
DTC P0606 (MZI-3.7) DETECTION CONDITIONS AND POSSIBLE CAUSES
STEP
INSPECTION
ACTION
1
VERIFY FREEZE FRAME DATA HAS
BEEN RECORDED
Has FREEZE FRAME DATA been
recorded?
Yes Go to next step.
No
Record FREEZE FRAME DATA on the repair
order, then go to next step.
2
VERIFY RELATED REPAIR
INFORMATION AVAILABILITY
Verify related Service Bulletins and/or
on-line repair information availability.
Is any related Service Bulletins
available?
Yes
Perform repair or diagnosis according to
available Service Bulletins.
If vehicle is not repaired, go to next step.
No
Perform PCM reprograming using the M-MDS,
then go to next step.
3
VERIFY TROUBLESHOOTING OF
DTC P0605 HAS BEEN COMPLETED
Verify that all disconnected connectors
are reconnected.
Turn the ignition switch to the ON
position (Engine off).
Clear the DTC from the PCM memory
using the M-MDS.
Perform the "KOEO and KOER self-
test". (See KOEO/KOER SELF
TEST [MZI-3.7].)
Retrieve DTCs using the M-MDS.
Is the PENDING CODE for this DTC
present?
Yes
Replace the PCM, then go to next step. (See
PCM REMOVAL/INSTALLATION [MZI-
3.7] .)
No
Go to next step.
4
VERIFY AFTER REPAIR PROCEDURE
Perform the "AFTER REPAIR
PRECAUTION". (See AFTER
REPAIR PROCEDURE [MZI-3.7].)
Are any DTCs present?
Yes
Go to the applicable DTC inspection. (See DTC
TABLE [MZI-3.7].)
No
Troubleshooting completed.
DTC P0606
ECM/PCM processor
DETECTION
CONDITION
This DTC indicates a register hardback (PCM internal
communications) error.
POSSIBLE CAUSE
PCM malfunction
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:39 AM
Page 267
© 2005 Mitchell Repair Information Company, LLC.
DIAGNOSTIC PROCEDURE
DTC P0606 (MZI-3.7) DIAGNOSTIC PROCEDURE
DTC P0607 [MZI-3.7]
DTC P0607 (MZI-3.7) DETECTION CONDITIONS AND POSSIBLE CAUSES
STEP
INSPECTION
ACTION
1
VERIFY FREEZE FRAME DATA HAS
BEEN RECORDED
Has FREEZE FRAME DATA been
recorded?
Yes Go to the next step.
No
Record FREEZE FRAME DATA on the repair
order, then go to the next step.
2
VERIFY RELATED REPAIR
INFORMATION AVAILABILITY
Verify related Service Bulletins
and/or on-line repair information
availability.
Is any related Service Bulletins
available?
Yes
Perform repair or diagnosis according to the
available Service Bulletins.
If the vehicle is not repaired, go to the next
step.
No
Perform PCM reprograming using the M-MDS,
then go to next step.
3
VERIFY TROUBLESHOOTING OF
P0606 HAS BEEN COMPLETED
Verify that all disconnected
connectors are reconnected.
Turn the ignition switch to the ON
position (Engine off).
Clear the DTC from the PCM
memory using the M-MDS.
Perform the "KOEO and KOER self-
test". (See KOEO/KOER SELF
TEST [MZI-3.7].)
Retrieve DTCs using the M-MDS.
Is the PENDING CODE for this DTC
present?
Yes
Replace the PCM, go to the next step. (See PCM
REMOVAL/INSTALLATION [MZI-3.7] .)
No
Go to the next step.
4
VERIFY AFTER REPAIR
PROCEDURE
Perform the "After Repair Procedure".
(See AFTER REPAIR
PROCEDURE [MZI-3.7].)
Are any DTCs present?
Yes
Go to the applicable DTC inspection. (See DTC
TABLE [MZI-3.7].)
No
Troubleshooting completed.
DTC P0607
Control module performance
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:39 AM
Page 268
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст