Mazda CX-9 Grand Touring. Manual — part 19
DIAGNOSTIC PROCEDURE
DTC B1868 DIAGNOSTIC PROCEDURE
Air bag warning system light malfunction.
STEP
INSPECTION
ACTION
1
VERIFY THAT SAS CONTROL MODULE
CONNECTOR IS CONNECTED
Turn the ignition switch to LOCK position.
Disconnect the negative battery cable and
wait for 1 min or more.
Are all SAS control module connectors
securely connected?
WARNING:
Handling the air bag system components
improperly can accidentally deploy the air
bag modules and pre-tensioner seat belts,
which may seriously injure you. Read the
air bag system service warnings and
cautions before handling the air bag
system components.
(See AIR BAG SYSTEM SERVICE
WARNINGS .)
(See AIR BAG SYSTEM SERVICE
CAUTIONS .)
Yes Go to the next step.
No
Reconnect the connector properly, then
go to the next step.
2
INSPECT DTCS IN SAS CONTROL MODULE
Inspect the DTC for the SAS control module
on-board diagnostic system.
Has DTC U0155, U0073 been recorded in
memory?
Yes
Perform the applicable DTC inspection.
(See DTC TABLE.)
No
Go to the next step.
3
INSPECT INSTRUMENT CLUSTER
Inspect the instrument cluster warning lights
using check code.
(See INSTRUMENT CLUSTER
INPUT/OUTPUT CHECK MODE .)
Are the check results okay?
Yes
Replace the SAS control module. (See
SAS CONTROL MODULE
REMOVAL/INSTALLATION .)
No
Repair or replace the instrument cluster
according to inspection results.
2008 Mazda CX-9 Grand Touring
2008 RESTRAINTS On-Board Diagnostic (Restraints) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:18:47 AM
Page 73
© 2005 Mitchell Repair Information Company, LLC.
DTC B1884, B1890
DTC B1884, B1890 DETECTION CONDITION AND POSSIBLE CAUSE
DIAGNOSTIC PROCEDURE
DTC B1884, B1890 DIAGNOSTIC PROCEDURE
DTC
B1884 Passenger air bag deactivation (PAD) indicator circuit open or short to body ground
B1890 Passenger air bag deactivation (PAD) indicator circuit short to power supply
DETECTION
CONDITION
Malfunction in PAD indicator circuit
WARNING:
Detection conditions are for understanding the DTC outline before performing an
inspection. Performing an inspection according to only the detection conditions
may cause injury due to an operating error, or damage the system. When
performing an inspection, always follow the inspection procedure.
POSSIBLE
CAUSE
Open or short circuit in wiring harness between information display and SAS control
module
Open circuit in wiring harness between battery and information display
information display malfunction
SAS control module malfunction
STEP
INSPECTION
ACTION
1
INSPECT OPERATION OF PAD INDICATOR
Turn the ignition switch to the ON position.
Does the PAD indicator illuminate?
Yes Go to the next step.
No
Go to Step 5.
INSPECT FUSE
Yes
Install the fuse, then go to the next
2008 Mazda CX-9 Grand Touring
2008 RESTRAINTS On-Board Diagnostic (Restraints) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:18:47 AM
Page 74
© 2005 Mitchell Repair Information Company, LLC.
2
Remove the METER 10 A fuse.
Is the fuse normal?
step.
No
Replace the fuse.
3
INSPECT BATTERY
Measure the battery positive voltage.
Is the voltage 9 V-16 V?
Yes Go to the next step.
No
Battery is malfunctioning Inspect the
charge/discharge system.
4
INSPECT WIRING HARNESS BETWEEN
BATTERY AND PAD INDICATOR
Turn the ignition switch to the ON position.
Measure the information display connector
terminal E voltage.
Is the voltage 9 V or more?
Yes Go to the next step.
No
Repair the wiring harness between the
battery and information display.
5
INSPECT WIRING HARNESS BETWEEN PAD
INDICATOR AND SAS CONTROL MODULE
Turn the ignition switch to the LOCK position.
Disconnect the negative battery cable and wait
for 1 min or more.
Remove the column cover. (See COLUMN
COVER REMOVAL/INSTALLATION .)
Disconnect the clock spring connector. (See
COMBINATION SWITCH
REMOVAL/INSTALLATION .)
Remove the glove compartment. (See GLOVE
COMPARTMENT
REMOVAL/INSTALLATION .)
Disconnect the passenger-side air bag module
connector. (See PASSENGER-SIDE AIR
WARNING:
Handling the air bag system components
improperly can accidentally deploy the air
bag modules and pre-tensioner front buckles,
which may seriously injure you. Read the
service warnings before handling the air bag
system components.
(See AIR BAG SYSTEM SERVICE
WARNINGS .)
(See AIR BAG SYSTEM SERVICE
CAUTIONS .)
Yes Go to the next step.
2008 Mazda CX-9 Grand Touring
2008 RESTRAINTS On-Board Diagnostic (Restraints) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:18:47 AM
Page 75
© 2005 Mitchell Repair Information Company, LLC.
DTC B2290
DTC B2290 DETECTION CONDITION AND POSSIBLE CAUSE
BAG MODULE
REMOVAL/INSTALLATION .)
Disconnect the driver and passenger-side front
seat connectors. (See FRONT SEAT
REMOVAL/INSTALLATION .)
Disconnect the driver and passenger-side curtain
air bag module connectors. (See CURTAIN
AIR BAG MODULE
REMOVAL/INSTALLATION .)
Remove the B-pillar lower trim. (See B-
PILLAR LOWER TRIM
REMOVAL/INSTALLATION .)
Disconnect the driver and passenger-side pre-
tensioner seat belt connectors. (See FRONT
SEAT BELT
REMOVAL/INSTALLATION .)
Disconnect the SAS control module connectors.
(See SAS CONTROL MODULE
REMOVAL/INSTALLATION .)
Inspect the wiring harness between information
display connector terminal K and SAS control
module connector terminal 1G for the
following:
Short to ground
Short to power supply
Open circuit
Is the wiring harness normal?
No
Replace the air bag wiring harness.
6
INSPECT PAD INDICATOR
Disconnect the SAS control module connector.
Connect the information display connector.
Does the PAD indicator illuminate?
Yes
Replace the information display.
(See INFORMATION DISPLAY
REMOVAL/INSTALLATION .)
No
Replace the SAS control module. (See
SAS CONTROL MODULE
REMOVAL/INSTALLATION .)
DTC B2290
Seat weight sensor signal malfunction
DETECTION
CONDITION
WARNING:
Detection conditions are for understanding the DTC outline before performing an
inspection. Performing an inspection according to only the detection conditions
may cause injury due to an operating error, or damage the system. When
performing an inspection, always follow the inspection procedure.
2008 Mazda CX-9 Grand Touring
2008 RESTRAINTS On-Board Diagnostic (Restraints) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:18:47 AM
Page 76
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст