Mazda CX-9 Grand Touring. Manual — part 37
Fig. 82: Connecting SST To Battery
Courtesy of MAZDA MOTORS CORP.
2008 Mazda CX-9 Grand Touring
2008 RESTRAINTS Air Bag System - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:16:38 AM
Page 53
© 2005 Mitchell Repair Information Company, LLC.
2008 DRIVELINE/AXLE
All Wheel Drive (AWD) - Mazda CX-9
ELECTRONIC AWD CONTROL SYSTEM LOCATION INDEX
Fig. 1: Identifying Wheel Drive Components (AWD)
Courtesy of MAZDA MOTORS CORP.
AWD CONTROL MODULE INSPECTION
1. Measure voltage or resistance at each AWD CM terminal using a voltmeter and an ohmmeter.
If not as specified, replace the AWD CM.
TERMINAL VOLTAGE LIST (REFERENCE)
NOTE:
AWD CM terminal voltage can vary depending on measuring conditions
and vehicle aging, resulting in misdiagnosis. Therefore, it is necessary to
perform an overall inspection of the input/output systems and AWD CM to
determine which part is malfunctioning.
With the AWD CM connector connected, measure voltage by connecting
the voltmeter negative (-) lead to the body ground and positive (+) lead to
each AWD CM terminal.
2008 Mazda CX-9 Grand Touring
2008 DRIVELINE/AXLE All Wheel Drive (AWD) - Mazda CX-9
2008 Mazda CX-9 Grand Touring
2008 DRIVELINE/AXLE All Wheel Drive (AWD) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:31:22 AM
Page 1
© 2005 Mitchell Repair Information Company, LLC.
Microsoft
Sunday, November 15, 2009 10:31:26 AM
Page 1
© 2005 Mitchell Repair Information Company, LLC.
Fig. 2: Identifying AWD Control Module Connector Terminal
Courtesy of MAZDA MOTORS CORP.
TERMINAL VOLTAGE LIST (REFERENCE)
Terminal
Signal
Input/output
Connected
to
Measuring
item
Test condition
Voltage
(V)/
Continuity
Inspection
location in case
of failure
A
Differential
oil
temperature
sensor
signal
Input
Differential
oil
temperature
sensor
Voltage
Ignition
key ON
Differential
oil
temperature
20°C {68°
F}
3.0
Inspect
differential
oil
temperature
sensor
Inspect
related
harness
Differential
oil
temperature
60°C{140°
F}
1.4
B
-
-
-
-
-
-
-
-
C
Differential
oil
temperature
sensor
GND
-
Differential
oil
temperature
sensor
Continuity Any condition
Yes
Inspect
related
harness
D
-
-
-
-
-
-
-
-
E
-
-
-
-
-
-
-
-
F
-
-
-
-
-
-
-
-
G
CAN_H
Input/output
-
Perform measurement during DTC
inspection.
-
H
CAN_L
Input/output
-
Perform measurement during DTC
inspection.
-
I
Power
supply
(Ignition
switch)
Input
Ignition
key
Voltage
Ignition key ON
B+
Inspect
fuse
Inspect
related
harness
Ignition key OFF
1.0 or
below
2008 Mazda CX-9 Grand Touring
2008 DRIVELINE/AXLE All Wheel Drive (AWD) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:31:22 AM
Page 2
© 2005 Mitchell Repair Information Company, LLC.
AWD CONTROL MODULE REMOVAL/INSTALLATION
1. Disconnect the negative battery cable.
2. Remove the dashboard undercover (Driver side). (See DASHBOARD UNDER COVER
REMOVAL/INSTALLATION .)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
J
-
-
-
-
-
-
-
-
K
Power
supply
(Main)
Input
Battery
Voltage
Any condition
B+
Inspect
fuse
Inspect
related
harness
L
-
-
-
-
-
-
-
-
M
-
-
-
-
-
-
-
-
N
Ground
-
Ground
Voltage
Any condition
0
Inspect
related
harness
O
AWD
solenoid
(+)
Output
AWD
solenoid
Voltage
Ignition key ON
B+
AWD
solenoid
Inspect
related
harness
Ignition key OFF
1.0 or
below
P
AWD
solenoid (-)
Output
AWD
solenoid
Voltage
Ignition key ON
B+
AWD
solenoid
Inspect
related
harness
Ignition key OFF
1.0 or
below
2008 Mazda CX-9 Grand Touring
2008 DRIVELINE/AXLE All Wheel Drive (AWD) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:31:22 AM
Page 3
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст