Mazda CX-9 Grand Touring. Manual — part 313
DTC P2122 [MZI-3.7]
DTC P2122 (MZI-3.7) DETECTION CONDITIONS AND POSSIBLE CAUSES
Is the PENDING CODE for the DTC
present?
No
Go to the next step.
13
VERIFY AFTER REPAIR PROCEDURE
Perform "AFTER REPAIR
PROCEDURE". (See AFTER REPAIR
PROCEDURE [MZI-3.7].)
Are any DTCs present?
Yes
Go to the applicable DTC inspection. (See
DTC TABLE [MZI-3.7].)
No
Troubleshooting completed.
DTC P2122
APP sensor No.1 circuit low input
DETECTION
CONDITION
APP sensor No.1 is out of self-test range low.
POSSIBLE CAUSE
Short to ground circuit between APP sensor terminal F and PCM terminal
1BA
Short to ground circuit between APP sensor terminal D and PCM terminal
1Y
Short to ground circuit between APP sensor terminal G and PCM terminal 1
AD
Short to ground circuit between APP sensor terminal C and PCM terminal
1AH
Short to ground circuit between APP sensor terminal E and PCM terminal
1AK
Connector or terminal malfunction
APP sensor malfunction
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:42 AM
Page 385
© 2005 Mitchell Repair Information Company, LLC.
DIAGNOSTIC PROCEDURE
DTC P2122 (MZI-3.7) DIAGNOSTIC PROCEDURE
STEP
INSPECTION
ACTION
1
VERIFY FREEZE FRAME DATA HAS
BEEN RECORDED
Has FREEZE FRAME DATA been
recorded?
Yes Go to the next step.
No
Record FREEZE FRAME DATA on the repair
order, then go to the next step.
VERIFY RELATED REPAIR
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:42 AM
Page 386
© 2005 Mitchell Repair Information Company, LLC.
2
INFORMATION AVAILABILITY
Verify related Service Bulletins
and/or on-line repair information
availability.
Is any related Service Bulletins
available?
Yes
Perform repair or diagnosis according to the
available Service Bulletins.
If the vehicle is not repaired, go to the next
step.
No
Go to the next step.
3
INSPECT APP SENSOR CONNECTOR
FOR POOR CONNECTION
Turn the ignition switch off.
Disconnect the APP sensor
connector.
Inspect for poor connection (such as
damaged/pulled-out pins, corrosion).
Is there any malfunction?
Yes
Repair or replace suspected part, then go to Step
7.
No
Go to the next step.
4
INSPECT APP SENSOR NO.1
CIRCUIT FOR SHORT TO GROUND
Turn the ignition switch off.
Inspect for continuity between the
following terminals:
APP sensor terminal F and
body ground.
APP sensor terminal D and
body ground.
APP sensor terminal G and
body ground.
APP sensor terminal C and
body ground.
APP sensor terminal E and
body ground.
Are there continuity?
Yes
Repair or replace suspected part, then go to Step
7.
No
Go to the next step.
5
INSPECT APP SENSOR NO.1
Inspect APP sensor No.1. (See
ACCELERATOR PEDAL
POSITION (APP) SENSOR
INSPECTION [MZI-3.7] .)
Is there any malfunction?
Yes
Replace the accelerator pedal, then go to Step 7.
(See ACCELERATOR PEDAL
REMOVAL/INSTALLATION [MZI-3.7] .)
No
Go to the next step.
INSPECT PCM CONNECTOR FOR
POOR CONNECTION
Yes
Repair or replace suspected part, then go to Step
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:42 AM
Page 387
© 2005 Mitchell Repair Information Company, LLC.
DTC P2123 [MZI-3.7]
DTC P2123 (MZI-3.7) DETECTION CONDITIONS AND POSSIBLE CAUSES
6
Turn the ignition switch off.
Disconnect the PCM connector.
Inspect for poor connection (such as
damaged/pulled-out pins, corrosion).
Is there any malfunction?
7.
No
Go to the next step.
7
VERIFY TROUBLESHOOTING OF
DTC P2122 HAS BEEN COMPLETED
Verify that all disconnected
connectors reconnected.
Clear the DTC from the PCM
memory using the M-MDS.
Start the engine.
Is the same DTC present?
Yes
Replace the PCM, then go to the next step. (See
PCM REMOVAL/INSTALLATION [MZI-
3.7] .)
No
Go to the next step.
8
VERIFY AFTER REPAIR
PROCEDURE
Perform the "AFTER REPAIR
PROCEDURE". (See AFTER
REPAIR PROCEDURE [MZI-
3.7].)
Are any DTC present?
Yes
Go to the applicable DTC inspection. (See DTC
TABLE [MZI-3.7].)
No
DTC troubleshooting completed.
DTC P2123
APP sensor No.1 circuit high input
DETECTION
CONDITION
APP sensor No.1 is out of self-test range high.
POSSIBLE CAUSE
Open circuit wiring harness between APP sensor terminal F and PCM
terminal 1BA
Open circuit wiring harness between APP sensor terminal D and PCM
terminal 1Y
Open circuit wiring harness between APP sensor terminal G and PCM
terminal 1AD
Open circuit wiring harness between APP sensor terminal C and PCM
terminal 1 AH
Open circuit wiring harness between APP sensor terminal E and PCM
terminal 1AK
Short to power supply in wiring harness between APP sensor terminal F and
PCM terminal 1 BA
Short to power supply in wiring harness between APP sensor terminal D and
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:42 AM
Page 388
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст