Mazda CX-9 Grand Touring. Manual — part 318
6
Turn the ignition switch off.
Inspect for continuity between the
following terminals (wiring harness-
side).
APP sensor terminal F and
PCM terminal 1BA.
APP sensor terminal D and
PCM terminal 1Y.
APP sensor terminal G and
PCM terminal 1AD.
APP sensor terminal C and
PCM terminal 1AH.
APP sensor terminal B and
PCM terminal 1AC.
Are there continuity?
Yes Go to the next step.
No
Repair or replace suspected part, then go to Step
8.
7
INSPECT APP SENSOR NO.3 SIGNAL
CIRCUIT FOR SHORT TO POWER
SUPPLY
Turn the ignition switch to the ON
position (Engine off).
Measure the voltage between the
following terminals (wiring harness-
side).
APP sensor terminal F and
body ground.
APP sensor terminal D and
body ground.
APP sensor terminal G and
body ground.
APP sensor terminal C and
body ground.
APP sensor terminal B and
body ground.
Are there voltage B+?
Yes
Repair or replace suspected part, then go to Step
8.
No
Go to the next step.
8
VERIFY TROUBLESHOOTING OF
DTC P2133 HAS BEEN COMPLETED
Verify that all disconnected
connectors reconnected.
Clear the DTC from the PCM
memory using the M-MDS.
Yes
Replace the PCM, then go to the next step. (See
PCM REMOVAL/INSTALLATION [MZI-
3.7] .)
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:43 AM
Page 405
© 2005 Mitchell Repair Information Company, LLC.
DTC P2135 [MZI-3.7]
DTC P2135 (MZI-3.7) DETECTION CONDITIONS AND POSSIBLE CAUSES
Start the engine.
Is the same DTC present?
No
Go to the next step.
9
VERIFY AFTER REPAIR
PROCEDURE
Perform the "AFTER REPAIR
PROCEDURE". (See AFTER
REPAIR PROCEDURE [MZI-
3.7].)
Are any DTC present?
Yes
Go to the applicable DTC inspection. (See DTC
TABLE [MZI-3.7].)
No
DTC troubleshooting completed.
DTC P2135
TP sensor No.1/No.2 voltage correlation
DETECTION
CONDITION
The PCM flagged a concern indicating that TP sensor No.1 and TP sensor No.2
disagree by more than a calibrated limit.
POSSIBLE CAUSE
Short to power supply between TP sensor No.1 terminal F and PCM terminal 2Z
Short to power supply between TP sensor No.2 terminal C and PCM terminal
2AD
TP sensor circuits are shorted each other
TP sensor malfunction
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:43 AM
Page 406
© 2005 Mitchell Repair Information Company, LLC.
DIAGNOSTIC PROCEDURE
DTC P2135 (MZI-3.7) DIAGNOSTIC PROCEDURE
STEP
INSPECTION
ACTION
VERIFY FREEZE FRAME DATA
HAS BEEN RECORDED
Yes Go to the next step.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:43 AM
Page 407
© 2005 Mitchell Repair Information Company, LLC.
1
Has FREEZE FRAME DATA been
recorded?
No
Record the FREEZE FRAME DATA on the repair
order, then go to the next step.
2
VERIFY RELATED REPAIR
INFORMATION AVAILABILITY
Verify related Service Bulletins
and/or on-line repair information
availability.
Is any related Service Bulletins
available?
Yes
Perform repair or diagnosis according to the
available Service Bulletins.
If the vehicle is not repaired, go to the next
step.
No
Go to the next step.
3
INSPECT TP SENSOR RESISTANCE
Turn the ignition switch off.
Disconnect the throttle body
connector.
Measure the resistance between the
following terminals (throttle body
component side).
Throttle body terminal F and
D: 700-1,800 ohms
Throttle body terminal F and
E: 1,300-2,800 ohms
Throttle body terminal C and
D: 1,000-2,400 ohms
Throttle body terminal C and
E: 500-1,500 ohms
Throttle body terminal D and
E: 700-2,100 ohms
Are all the resistances within
specifications?
Yes Go to the next step.
No
Replace the throttle body, then go to Step 6. (See
INTAKE-AIR SYSTEM
REMOVAL/INSTALLATION [MZI-3.7] .)
4
INSPECT TP SENSOR SIGNAL
CIRCUIT FOR SHORT TO POWER
SUPPLY
Turn the ignition switch to the ON
position (Engine off).
Measure the voltage between the
following circuits:
Throttle body terminal F
(wiring harness-side) and
body ground.
Throttle body terminal C
(wiring harness-side) and
Yes Repair or replace suspected part, then go to Step 6.
No
Go to the next step.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:43 AM
Page 408
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст