Mazda CX-9 Grand Touring. Manual — part 110

10. Rotate the slider pin to release the lock and verify that it slides freely.

11. Pull the slider pin outward until it contacts the brake pedal stopper rubber and rotate the slider pin to lock.

12. Verify that the selector lever in the P position.

Fig. 36: Pulling Slider Pin Outward Until It Contacts Brake Pedal Stopper Rubber
Courtesy of MAZDA MOTORS CORP.

13. Install the interlock cable end to the cam pin on the selector lever.

14. Fit the interlock cable in the U-groove in the selector lever base plate and install the clip.

Fig. 37: Identifying Interlock Cable And Clip
Courtesy of MAZDA MOTORS CORP.

Fig. 35: Pressing Slider Pin
Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle Shift Mechanism - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:30:13 AM

Page 17

© 2005 Mitchell Repair Information Company, LLC.

15. Press the interlock cable lock piece in until it is locked.

16. Remove the a 1.5 mm {0.059 in} round bar or similar from the lock unit holes A, B, and C.

Fig. 39: Identifying Lock Unit Holes A, B, And C
Courtesy of MAZDA MOTORS CORP.

17. Connect the brake switch connector with the brake pedal released.

CAUTION:



Applying a load to the interlock cable while pressing the lock
piece in can affect the lock unit operation.

Fig. 38: Identifying Interlock Cable Lock Piece
Courtesy of MAZDA MOTORS CORP.

CAUTION:



The clearance between the brake switch and the brake pedal is
automatically adjusted to the correct amount when the brake
switch connector is connected after the brake switch has been
properly installed. If the brake switch is not properly installed or
the connector is connected before installation, the clearance
may be incorrect, causing a brake light malfunction. Therefore,
always verify that the brake switch is properly installed before
connecting the connector.



Once the brake switch clearance has automatically been
adjusted, it cannot be adjusted again. Therefore, replace the

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle Shift Mechanism - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:30:13 AM

Page 18

© 2005 Mitchell Repair Information Company, LLC.

18. Turn the ignition switch to ON position.

19. Install the interlock cable to the steering lock.

20. Slide the outer casing to the steering lock and insert the clip over the convex part of the outer casing.

Fig. 40: Identifying Clip And Convex Part
Courtesy of MAZDA MOTORS CORP.

switch with a new one when replacing the power brake unit or
the pedal, or performing any procedure that changes the pedal
stroke.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle Shift Mechanism - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:30:13 AM

Page 19

© 2005 Mitchell Repair Information Company, LLC.

2008 ACCESSORIES & BODY, CAB

Body Panels - Mazda CX-9

REAR BUMPER REINFORCEMENT REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.

2. Remove the rear combination light. (See REAR COMBINATION LIGHT

REMOVAL/INSTALLATION .)

3. Remove the rear bumper. (See REAR BUMPER REMOVAL/INSTALLATION.)

4. Remove the fasteners, then remove the energy-absorbing foam.

5. Remove the bolts and nuts, then remove the rear bumper reinforcement.

6. Install in the reverse order of removal.

Fig. 1: Identifying Rear Bumper Reinforcement & Torque Specifications
Courtesy of MAZDA MOTORS CORP.

BODY PANELS LOCATION INDEX

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Body Panels - Mazda CX-9

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Body Panels - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:44:45 AM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

Microsoft

Sunday, November 15, 2009 10:44:49 AM

Page 1

© 2005 Mitchell Repair Information Company, LLC.