Mazda Transaxle FN4A-EL. Manual — part 6
K1–16
AUTOMATIC TRANSAXLE
54. Remove the oil pipe.
End Of Sie
ACCUMULATORS DISASSEMBLY/ASSEMBLY
A6E561419200A01
1. Disassemble in the order indicated in the table.
2. Assemble in the reverse order of disassembly.
.
Assembly Procedure
1. Measure the spring free length.
2. If not as specified, replace the spring.
X3U517ABB
1
Servo apply accumulator
2
Servo apply accumulator large spring
3
Servo apply accumulator small spring
4
Forward accumulator
5
Forward accumulator large spring
6
Forward accumulator small spring
A6E5714A032
Spring
Outer diameter
mm {in}
Free length
mm {in}
No. of coils
Wire diameter
mm {in}
Servo apply accumulator large spring
21.0 {0.827}
67.8 {2.669}
10.3
3.5 {0.138}
Servo apply accumulator small spring
13.0 {0.512}
67.8 {2.669}
17.1
2.2 {0.087}
Forward accumulator large spring
21.0 {0.827}
75.0 {2.953}
10.7
2.3 {0.091}
Forward accumulator small spring
15.6 {0.614}
49.0 {1.929}
7.7
2.4 {0.094}
AUTOMATIC TRANSAXLE
K1–17
K1
3. Install the forward accumulator small spring,
forward accumulator large spring and forward
accumulator.
4. Install the servo apply accumulator small spring,
servo apply accumulator large spring and servo
apply accumulator.
End Of Sie
X3U517ABD
X3U517ABE
K1–18
AUTOMATIC TRANSAXLE
CLUTCH COMPONENT DISASSEMBLY/ASSEMBLY
A6E561419500A01
1. Carry out the preinspection before disassembly. (See
K1–50 Clutch Component Preinspection
2. Disassemble in the order indicated in the table.
3. Assemble in the reverse order of disassembly.
.
A6E5714A033
1
Snap ring
2
Rear sun gear plate
3
Bearing
4
3-4 clutch hub
5
Bearing
6
Snap ring
7
Retaining plate
8
Drive and driven plate
9
Snap ring
(See
K1–19 Snap Ring (3-4 clutch) Disassembly
)
10
Seal plate
11
Spring and retainer component
12
3-4 clutch piston
(See
K1–19 3-4 Clutch Piston Disassembly Note
)
13
3-4 clutch drum
14
Snap ring
15
Retaining plate
16
Drive and driven plate
17
Dish plate
18
Snap ring
(See
K1–19 Snap Ring (Reverse clutch)
19
Reverse return stopper
20
Piston return spring
21
Reverse piston
(See
K1–20 Reverse Piston Disassembly Note
)
22
2-4 brake drum
23
Bearing
AUTOMATIC TRANSAXLE
K1–19
K1
Snap Ring (3-4 clutch) Disassembly Note
1. Install the SST as shown.
Caution
••••
Depress the seal plate only enough to remove the snap ring. Overpressing will damage the seal
plate assembly edges.
2. Compress the seal plate.
3. Remove the snap ring.
4. Remove the SST, then remove the seal plate and
spring and retainer component.
3-4 Clutch Piston Disassembly Note
1. Set the 3-4 clutch drum onto the end cover.
2. Remove the 3-4 clutch piston from the 3-4 clutch
drum by applying compressed air through the
fluid passage.
Air pressure
392 kPa {4.0 kgf/cm
2
, 57 psi} max.
Snap Ring (Reverse clutch) Disassembly Note
1. Install the SSTs as shown.
Caution
••••
Depress the piston return spring only enough to remove the snap ring. Overpressing will damage
the piston return spring assembly edges.
2. Compress the piston return spring.
3. Remove the snap ring.
4. Remove the SSTs, then remove the reverse
return stopper and return spring.
A6E5714A034
A6E5714A035
A6E5714A036
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст