Mazda Protege 5. Manual — part 198
DRIVE SHAFT
03–13–16
Boot Band (Transaxle Side) Assembly Note
1. Fold the band back and use pliers to pull it tight.
Note
•
Always use new bands.
•
The band should be folded in the direction
opposite to the forward revolving direction of
the drive shaft.
2. Lock the end of the band by bending the locking
clips.
Caution
••••
Verify that the boot band is installed in
the boot groove securely.
Boot Band (Wheel Side) Assembly Note
1. Adjust clearance A by turning the adjusting bolt of the SST.
Clearance A
2.9 mm {0.11 in}
2. Crimp the wheel side small boot band using the
SST. Verify that clearance B is within the
specification.
•
If clearance B is more than the specification,
reduce clearance A of the SST and crimp the
boot again.
•
If clearance B is less than the specification,
replace the boot band, increase clearance A
of the SST, and crimp the new boot.
Clearance B
2.4—2.8 mm {0.095—0.110 in}
3. Verify that the boot band does not protrude from
the boot band installation area.
•
If it does, replace the boot band and repeat
from Step 1.
4. Fill the boot with the repair kit grease.
5. Adjust clearance A by turning the adjusting bolt of
the SST.
Clearance A
3.2 mm {0.13 in}
6. Crimp the wheel side big boot band using the SST.
7. Verify that clearance B is within the specification.
•
If clearance B is more than the specification,
reduce clearance A of the SST and crimp the boot again.
•
If clearance B is less than the specification, replace the boot band, increase clearance A of the SST and
crimp the new boot.
Clearance B
2.4—2.8 mm {0.095—0.110 in}
8. Verify that the boot band does not protrude from the boot band installation area.
•
If it does, replace the boot band and repeat from Steps 5.
End Of Sie
Y3E6316W035
Z3U0313W009
Y3E6316W028
1712-1U-01G(03-13).fm 16 ページ 2001年6月29日 金曜日 午前9時59分
DRIVE SHAFT
03–13–17
03–13
DRIVE SHAFT (FS MTX LEFT SIDE) DISASSEMBLY/ASSEMBLY
A3U031325500W05
1. Disassemble in the order indicated in the table.
2. Assemble in the reverse order of disassembly.
.
A3U0313W005
1
Boot band (wheel side)
(See 03–13–12 DRIVE SHAFT (ZM, FS ATX, FS
MTX RIGHT SIDE) DISASSEMBLY/ASSEMBLY)
2
Boot band (transaxle side)
(See 03–13–12 DRIVE SHAFT (ZM, FS ATX, FS
MTX RIGHT SIDE) DISASSEMBLY/ASSEMBLY)
3
Clip
(See 03–13–18 Outer Ring Disassembly Note)
(See 03–13–19 Outer Ring, Clip Assembly Note).
4
Outer ring
(See 03–13–19 Outer Ring, Clip Assembly Note)
5
Snap ring
(See 03–13–19 Cage, Inner Ring, Balls, Snap Ring
Assembly Note)
6
Balls
(See 03–13–18 Balls, Inner Ring, Cage
Disassembly Note)
(See 03–13–19 Cage, Inner Ring, Balls, Snap Ring
Assembly Note)
7
Inner Ring
(See 03–13–18 Balls, Inner Ring, Cage
Disassembly Note)
(See 03–13–19 Cage, Inner Ring, Balls, Snap Ring
Assembly Note)
8
Cage
(See 03–13–18 Balls, Inner Ring, Cage
Disassembly Note)
(See 03–13–19 Cage, Inner Ring, Balls, Snap Ring
Assembly Note)
9
Boot
(See 03–13–18 Boot Assembly Note)
10
Dynamic damper
(See 03–13–18 Dynamic Damper Assembly Note)
11
ABS sensor rotor
(See 03–13–12 DRIVE SHAFT (ZM, FS ATX, FS
MTX RIGHT SIDE) DISASSEMBLY/ASSEMBLY)
12
Shaft and ball joint component
1712-1U-01G(03-13).fm 17 ページ 2001年6月29日 金曜日 午前9時59分
DRIVE SHAFT
03–13–18
Outer Ring Disassembly Note
1. Mark the drive shaft and outer ring for proper
assembly.
Caution
••••
Mark with paint; do not use a punch.
2. Remove the clip.
Balls, Inner Ring, Cage Disassembly Note
1. Mark the inner ring and cage.
Caution
••••
Mark with paint; do not use a punch.
2. Remove the snap ring using snap-ring pliers.
3. Turn the cage approximately 30 degree and pull
the cage and balls away from the inner ring.
Dynamic Damper Assembly Note
1. Install the dynamic damper as shown in the
figure.
Standard length
292—298 mm {11.5—11.7 in}
2. Install the new boot band onto the dynamic
damper.
Boot Assembly Note
1. Fill the boot (wheel side) with the specified grease from a tube, not by hand.
Caution
••••
Do not touch grease with your hand. Apply it from the tube to prevent foreign matter from entering
the boot.
Note
•
The wheel side and transaxle side boots are different.
•
Use the specified grease supplied in the boot kit.
Grease amount
75—95 g {2.65—3.35 oz}
Z3U0313W005
YYJ6316W007
ZLU0313W141
1712-1U-01G(03-13).fm 18 ページ 2001年6月29日 金曜日 午前9時59分
DRIVE SHAFT
03–13–19
03–13
2. With the splines of the shaft still wrapped in tape from disassembly, install the boot.
3. Remove the tape.
Cage, Inner Ring, Balls, Snap Ring Assembly Note
1. Align the marks and install the balls and cage to
the inner ring in the direction shown in the figure.
Caution
••••
Install the cage with the offset facing the
snap ring groove. If incorrectly installed,
the drive shaft may become disengaged.
2. Install a new snap ring.
Outer Ring, Clip Assembly Note
1. Fill the outer ring and boot (transaxle side) with the specified grease.
Caution
••••
Do not touch grease with your hand. Apply it from the tube to prevent foreign matter from entering
the boot.
Note
•
Use the specified grease supplied in the boot kit.
Grease amount
95—115 g {3.36—4.05 oz}
2. Align the marks, and install the outer ring on to the shaft.
3. Install a new clip.
4. Install the boot.
5. Set the drive shaft to the standard length.
Standard length
641.0—651.0 {25.24—25.62}
6. Release any trapped air from the boots by
carefully lifting up the small end of each boot with
a cloth wrapped screwdriver.
Caution
••••
Be careful not to allow the grease to leak.
••••
Do not damage the boot.
7. Verify that the drive shaft length is within the
specification.
End Of Sie
Z3U0313W006
Y3E6316W033
1712-1U-01G(03-13).fm 19 ページ 2001年6月29日 金曜日 午前9時59分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст