Mazda Protege 5. Manual — part 352
INSTRUMENTATION/DRIVER INFO.
09–22–2
End Of Sie
INSTRUMENT CLUSTER SYSTEM WIRING DIAGRAM
A3U092255430W01
End Of Sie
Z3U0922W005
1712-1U-01G(09-22).fm 2 ページ 2001年6月29日 金曜日 午前10時39分
INSTRUMENTATION/DRIVER INFO.
09–22–3
09–22
INSTRUMENT CLUSTER REMOVAL/INSTALLATION
A3U092255430W02
1. Disconnect the negative battery cable.
2. Pull down the adjusting lever of the tilt steering wheel and push the steering wheel down.
3. Remove the meter hood.
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
Instrument Cluster Removal Note
1. When removing the instrument cluster, in order to
prevent damage to the lens, cover the steering
shaft with a cloth.
End Of Sie
INSTRUMENT CLUSTER DISASSEMBLY/ASSEMBLY
A3U092255430W03
Caution
••••
If the instrument cluster is dropped or the print plate is damaged, the system will not operate
properly and it may become the cause of trouble or malfunctions.
1. Disassemble in the order indicated in the table.
2. Assemble in the reverse order of disassembly.
End Of Sie
1
Screw
2
Connector
3
Instrument cluster
(See 09–22–3 Instrument Cluster Removal Note)
X3U922WA0
X3U922WA1
1
Screw
2
Bracket
3
Lens
4
Bulb
5
Screw
6
Cover
7
Screw
8
Instrument cluster
9
Case
Z3U0922W001
1712-1U-01G(09-22).fm 3 ページ 2001年6月29日 金曜日 午前10時39分
INSTRUMENTATION/DRIVER INFO.
09–22–4
INSTRUMENT CLUSTER INSPECTION
A3U092255430W04
Speedometer
1. Inspect the speedometer by setting it in the input/output check mode DTC 12. (See 09–22–5 INSTRUMENT
CLUSTER INPUT/OUTPUT CHECK MODE.)
Tachometer
1. Inspect the tachometer by setting it in the input/output check mode DTC 13. (See 09–22–5 INSTRUMENT
CLUSTER INPUT/OUTPUT CHECK MODE.)
Fuel Gauge
1. Inspect the fuel gauge by setting it in the input/output check mode DTC 23. (See 09–22–5 INSTRUMENT
CLUSTER INPUT/OUTPUT CHECK MODE.)
Water Temperature Gauge
1. Inspect the water temperature gauge by setting it in the input/output check mode DTC 25. (See 09–22–5
INSTRUMENT CLUSTER INPUT/OUTPUT CHECK MODE.)
End Of Sie
INSTRUMENT CLUSTER REPAIR
A3U092255430W05
Tachometer
Note
•
The tach needle will not return to zero if the engine is turned off while the engine speed is 4,000 rpm or
higher when the ROOM fuse is not installed. The tach needle will continue to rotate clockwise until it rests
on the wrong side of the stopper pin. If a customer complains of this concern, inspect the ROOM fuse and
if necessary, repair according to the following steps.
1. Verify the concern.
2. Verify that the ROOM fuse is installed.
3. Start the engine and increase the engine speed to
approximately 5,500 rpm or until the needle
begins to move away from the stopper pin
(counterclockwise).
4. Decrease the engine speed to idle and turn the
ignition switch to LOCK position.
5. Verify that the needle returns to zero.
•
If the needle does not return to zero, remove
the lens and carefully move the needle by
hand.
End Of Sie
X3U922WC0
X3U922WC1
X3U922WC2
1712-1U-01G(09-22).fm 4 ページ 2001年6月29日 金曜日 午前10時39分
INSTRUMENTATION/DRIVER INFO.
09–22–5
09–22
INSTRUMENT CLUSTER INPUT/OUTPUT CHECK MODE
A3U092255430W06
Note
•
In this mode, it is possible to check the items in the following chart.
DTC Chart
Note
•
The diagnostic trouble codes are displayed in numerical order. (While performing the inspection, if you
want to inspect a diagnostic trouble code number which is smaller than the code number you are currently
inspecting, terminate the check mode then repeat the inspection from the beginning.)
•
If the speed signal is put into the instrument cluster (the front wheels are rotated) while a code other than
DTC 10 is displayed, the input/output check mode will be cancelled.
•
The diagnostic trouble codes can be fast-forwarded by pushing and holding the odometer/tripmeter switch
for 1 second or more.
DTC
Checking item
Related item
01
Buckle switch
Buckle switch
04
Door switch
•
Ignition key illumination
•
Room light control
•
Power door lock system
•
Lights-on reminder warning buzzer
05
Door lock-link switch
Room light control
08
TNS relay
•
Lights-on reminder warning buzzer
•
Each illumination
10
With ABS
•
ABS HU/CM (vehicle speed signal)
Without ABS, MTX
•
Vehicle speedometer sensor (vehicle speed signal)
Without ABS, ATX
•
PCM (vehicle speed signal)
Speedometer
11
PCM (engine speed signal)
Tachometer
12
Speedometer
Speedometer
13
Tachometer
Tachometer
14
Buzzer
•
Lights-on reminder warning buzzer
•
Key reminder warning buzzer
16
Fuel-level warning light
Fuel-level warning light
22
Fuel gauge sender unit
Fuel gauge
23
Fuel gauge
Fuel gauge
24
ECT sensor
Water temperature gauge
25
Water temperature gauge
Water temperature gauge
26
LCD
LCD
27
Interior light
Room light control
31
Key reminder switch
•
Room light control
•
Keyless entry system
1712-1U-01G(09-22).fm 5 ページ 2001年6月29日 金曜日 午前10時39分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст