Mazda Protege 5. Manual — part 343

LIGHTING SYSTEMS

09–18–25

09–18

Rear

1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.

3. Install in the reverse order of removal.

End Of Sie

DOOR SWITCH INSPECTION

A3U091866540W02

1. Remove the door switch. (See 09–18–24 DOOR SWITCH REMOVAL/INSTALLATION.)
2. Inspect for continuity between the door switch terminal and a body ground using an ohmmeter.

•

If not as specified, replace the door switch.

End Of Sie

PANEL LIGHT CONTROL SWITCH REMOVAL/INSTALLATION

A3U091866600W01

1. Disconnect the negative battery cable.
2. Remove the driver-side side panel.
3. Remove in the order indicated in the table.

4. Install in the reverse order of removal.

Panel Light Control Switch Removal Note

1. Insert your hand into the hole in the driver-side side panel, grasp the tabs of the panel light control switch and

pull it forward to remove.

End Of Sie

1

Screw

2

Connector

3

Door switch

Y3U918WAF

X3U918WB9

X3U918WBR

1

Panel light control switch
(See 09–18–25 Panel Light Control Switch Removal
Note)

2

Connector

Y3U918WAS

1712-1U-01G(09-18).fm 25 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS

09–18–26

PANEL LIGHT CONTROL SWITCH INSPECTION

A3U091866600W02

1. Remove the panel light control switch. (See 09–18–25 PANEL LIGHT CONTROL SWITCH REMOVAL/

INSTALLATION.)

2. Connect the negative battery cable.
3. Connect the connector to the panel light control switch.
4. Measure the voltage at the panel light control switch as indicated below.
5. Disconnect the panel light control switch connector before inspecting for continuity at terminal D.

•

If not as specified, inspect the parts listed under “Action.”

•

If the parts and wiring harnesses are okay but the system still does not work properly, replace the panel
light control switch.

Terminal Voltage List (Reference)

Terminal C inspection

1. Measure the wave pattern of the C terminal on

the panel light control switch using an
oscilloscope.

2. Set the headlight switch to either the TNS or

headlight position.

3. Set the panel light control switch to the brightest

position.

4. Verify that the pattern on the screen is as shown

in the figure.

Terminal

Signal

Connected to

Test condition

Voltage (V)/

Continuity

Action

A

—

—

—

—

—

B

TNS

TNS relay

Headlight switch at TNS or headlight
position

B+

•

Inspect TNS
relay

•

Inspect
combination
switch

•

Inspect TAIL 15 A
fuse

•

Inspect related
harness

Other

Below 1.0

C

Illumination

Each illumination

Inspect using an oscilloscope
(See 09–18–26 Terminal C inspection)

—

•

Inspect each
illumination

•

Inspect related
harness

D

Ground

GND

Constant: inspect for continuity to
ground

Yes

•

Inspect GND

Y3U918WAG

X3U918WBC

X3U918WBD

1712-1U-01G(09-18).fm 26 ページ ２００１年６月２９日 金曜日 午後１２時５７分

LIGHTING SYSTEMS

09–18–27

09–18

5. Verify that the pattern on the screen matches the

pattern shown in the figure as the panel light
control switch is gradually turned to the darkest
position.

End Of Sie

X3U918WBE

1712-1U-01G(09-18).fm 27 ページ ２００１年６月２９日 金曜日 午後１２時５７分

WIPER/WASHER SYSTEM

09–19–1

09–19

09–19

WIPER/WASHER SYSTEM

LOCATION INDEX . . . . . . . . . . . . . . . . . 09–19–2

Windshield Wiper and Washer System 09–19–2
Rear Wiper and Washer System . . . . . 09–19–3

WIPER/WASHER SYSTEMS

WIRING DIAGRAM . . . . . . . . . . . . . . . . 09–19–4

WINDSHIELD WIPER ARM AND BLADE

ADJUSTMENT . . . . . . . . . . . . . . . . . . . 09–19–5

WINDSHIELD WIPER ARM AND BLADE

REMOVAL/INSTALLATION . . . . . . . . . 09–19–5

Windshield Wiper Arm

Installation Note . . . . . . . . . . . . . . . . . 09–19–5

WINDSHIELD WIPER LINK

REMOVAL/INSTALLATION . . . . . . . . . 09–19–5

WINDSHIELD WIPER MOTOR

REMOVAL/INSTALLATION . . . . . . . . . 09–19–6

WINDSHIELD WIPER MOTOR

INSPECTION . . . . . . . . . . . . . . . . . . . . . 09–19–6

WASHER TANK

REMOVAL/INSTALLATION . . . . . . . . . 09–19–7

WINDSHIELD WASHER MOTOR

REMOVAL/INSTALLATION . . . . . . . . . 09–19–7

WINDSHIELD WASHER MOTOR

INSPECTION . . . . . . . . . . . . . . . . . . . . . 09–19–8

WASHER FLUID-LEVEL SENSOR

REMOVAL/INSTALLATION . . . . . . . . . 09–19–8

WASHER FLUID-LEVEL SENSOR

INSPECTION . . . . . . . . . . . . . . . . . . . . . 09–19–8

WIPER AND WASHER SWITCH

REMOVAL/INSTALLATION . . . . . . . . . 09–19–9

WIPER AND WASHER SWITCH

INSPECTION . . . . . . . . . . . . . . . . . . . . . 09–19–9

Windshield Wiper and Washer. . . . . . . 09–19–9
Rear Wiper and Washer . . . . . . . . . . . 09–19–10

WINDSHIELD WASHER NOZZLE

ADJUSTMENT . . . . . . . . . . . . . . . . . . . . 09–19–10

WINDSHIELD WASHER NOZZLE

CLEANING . . . . . . . . . . . . . . . . . . . . . . . 09–19–11

WINDSHIELD WASHER NOZZLE

REMOVAL . . . . . . . . . . . . . . . . . . . . . . . 09–19–11

WINDSHIELD WASHER NOZZLE

INSTALLATION . . . . . . . . . . . . . . . . . . . 09–19–11

WINDSHIELD WASHER HOSE

REMOVAL/INSTALLATION . . . . . . . . . . 09–19–11

REAR WIPER ARM AND BLADE

ADJUSTMENT . . . . . . . . . . . . . . . . . . . . 09–19–12

REAR WIPER ARM AND BLADE

REMOVAL/INSTALLATION . . . . . . . . . . 09–19–12

Rear Wiper Arm Installation Note . . . . . 09–19–12

REAR WIPER MOTOR

REMOVAL/INSTALLATION . . . . . . . . . . 09–19–12

REAR WIPER MOTOR INSPECTION . . . 09–19–13
REAR WASHER MOTOR

REMOVAL/INSTALLATION . . . . . . . . . . 09–19–14

REAR WASHER MOTOR INSPECTION . 09–19–14
REAR WASHER NOZZLE

REMOVAL/INSTALLATION . . . . . . . . . . 09–19–14

REAR WASHER NOZZLE

ADJUSTMENT . . . . . . . . . . . . . . . . . . . . 09–19–15

REAR WASHER NOZZLE CLEANING . . 09–19–15
REAR WASHER HOSE

REMOVAL/INSTALLATION . . . . . . . . . . 09–19–15

INTERMITTENT REAR WIPER RELAY

REMOVAL/INSTALLATION . . . . . . . . . . 09–19–16

INTERMITTENT REAR WIPER RELAY

INSPECTION . . . . . . . . . . . . . . . . . . . . . 09–19–16

Terminal Voltage Table (Reference) . . 09–19–16

End of Toc

1712-1U-01G(09-19).fm 1 ページ ２００１年６月２９日 金曜日 午前１０時３７分