Mazda Protege 5. Manual — part 349
ENTERTAINMENT
09–20–6
REAR ANTENNA FEEDER INSPECTION
A3U092066942W02
1. Remove the rear antenna feeder.
2. Verify that there is no continuity between rear antenna feeder terminals A and B using an ohmmeter.
3. Inspect for continuity between the rear antenna
feeder terminals using an ohmmeter.
•
If not as specified, replace the rear antenna
feeder.
End Of Sie
AUDIO UNIT REMOVAL
A3U092066900W01
1. Disconnect the negative battery cable.
2. Remove the hole covers by inserting a small
tape-wrapped screwdriver into the slot and
carefully pry them off without scratching the
center panel. Pry up and pull off the hole covers
carefully to prevent the posts from breaking off.
3. With the beveled parts of the SST facing inward,
insert them into the unit.
Note
•
Two sets of the SSTs are necessary to
remove the audio unit.
4. Pull the SST outward and forward to slide out the
unit.
5. Disconnect the connectors and antenna jack.
End Of Sie
AUDIO UNIT INSTALLATION
A3U092066900W02
Caution
••••
Make certain that the wiring harness and antenna feeder are not caught between the unit and
dashboard. If the harness or the antenna feeder is caught between the unit and dashboard, it may
become the cause of trouble or malfunctions.
1. Connect the connectors and antenna jack.
2. Insert the unit until each clip clicks into place.
Caution
••••
To install audio unit, be sure to push
service hole cover areas on both sides of
the audio unit. If switches are pressed
instead, it may become the cause of
trouble or malfunctions.
3. Install the service hole covers.
4. Connect the negative battery cable.
End Of Sie
A3U0920W101
Y3A8124W002
YDE81241201
YDJ8124W107
YDJ8124W108
1712-1U-01G(09-20).fm 6 ページ 2001年6月29日 金曜日 午前10時37分
ENTERTAINMENT
09–20–7
09–20
UPPER MODULE REMOVAL/INSTALLATION
A3U092066900W03
1. Disconnect the negative battery cable.
2. Remove the audio unit. (See 09–20–6 AUDIO UNIT REMOVAL.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
Upper Module Removal Note
1. Insert a screwdriver into the hole stamped mark.
2. To remove upper module, lift it by pushing down
the screwdriver’s handle.
Cover Removal Note
1. Insert a tape-wrapped screwdriver between the
cover and the base unit, then unlatch hook A.
2. To unlatch hook B, pull the cover upward.
Screw Installation Note
Caution
••••
If an undesignated screw is used, the inside of the upper module could be damaged. When
installing the module, be sure to use a designated screw (red).
1
Screw
(See 09–20–7 Screw Installation Note)
2
Upper module
(See 09–20–7 Upper Module Removal Note)
3
Cover
(See 09–20–7 Cover Removal Note)
Y5J8124W004
YLE8124W005
YLE8124W006
1712-1U-01G(09-20).fm 7 ページ 2001年6月29日 金曜日 午前10時37分
ENTERTAINMENT
09–20–8
End Of Sie
LOWER MODULE REMOVAL/INSTALLATION
A3U092066900W04
1. Disconnect the negative battery cable.
2. Remove the audio unit. (See 09–20–6 AUDIO UNIT REMOVAL.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
Cover Removal Note
1. Insert the SST into the service holes on the bottom surface of the lower module.
2. To remove the cover, push the SST in the
direction shown by the arrow.
Screw Installation Note
Caution
••••
If an undesignated screw is used, the inside of the upper module could be damaged. When
installing the module, be sure to use a designated screw (red).
End Of Sie
CIGARETTE LIGHTER REMOVAL/INSTALLATION
A3U092067000W01
1. Disconnect the negative battery cable.
2. Remove the console. (See 09–17–5 CONSOLE
REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
1
Cover
(See 09–20–8 Cover Removal Note)
2
Screw
(See 09–20–8 Screw Installation Note)
3
Lower module
YLE8124W007
ZLU0920W003
1
Cigarette lighter plug
2
Connector
3
Socket
(See 09–20–9 Socket Removal Note)
4
Ring
(See 09–20–9 Ring Removal Note)
X3U920WAG
1712-1U-01G(09-20).fm 8 ページ 2001年6月29日 金曜日 午前10時37分
ENTERTAINMENT
09–20–9
09–20
Socket Removal Note
1. Turn the socket while pushing the protrusion of
the ring through the hole of the socket with a
tape-wrapped screwdriver.
2. Push the socket forward.
3. Return the socket clockwise to original angle
position as shown to pull it out forward.
Ring Removal Note
1. Pull the ring forward while pushing the tabs.
End Of Sie
CIGARETTE LIGHTER INSPECTION
A3U092067000W02
1. Turn the ignition switch to ACC position.
2. Verify that the cigarette lighter plug will move normally within 10—20 seconds, after pressing the plug into the
socket.
•
If the cigarette lighter does not operate normally, replace the cigarette lighter and socket. (See 09–20–8
CIGARETTE LIGHTER REMOVAL/INSTALLATION.)
End Of Sie
X3U920WAH
X3U920WAJ
Y3U920WA3
1712-1U-01G(09-20).fm 9 ページ 2001年6月29日 金曜日 午前10時37分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст