Mazda X-5. Manual — part 106
SECURITY AND LOCKS [ADVANCED KEYLESS SYSTEM]
09–14A–19
09–14A
Structural View
End Of Sie
IMMOBILIZER SYSTEM BLOCK DIAGRAM
E5U091467000N02
End Of Sie
SECURITY LIGHT
COIL ANTENNA
AUXILIARY KEY
(TRNSPONDER)
PCM
KEYLESS
CONTROL
MODULE
INSTRUMENT
CLUSTER
E5U914AS1015
IG1
IG1
IG1
B+
COIL
ANENNA
Tx
Rx
Tx
Rx
KEYLESS
CONTROL
MODULE
INSTRUMENT
CLUSTER
SECURITY
LIGHT
PCM
Hs-CAN
E5U914AS1016
SECURITY AND LOCKS [ADVANCED KEYLESS SYSTEM]
09–14A–20
IMMOBILIZER SYSTEM CONSTRUCTION/OPERATION
E5U091467000N03
• Keys contain a unique ID number that is previously programmed to the keyless control module and PCM. Due
to this, if immobilizer system component parts are replaced (such as key addition/clearing or replacement of
the keyless control module, instrument cluster or PCM), it is necessary to reset the system.
Key ID Number Verification Procedure
The start knob is pressed and the ignition switch is turned
to the ON position.
The PCM verifies that the received key ID number matches
the key ID number which has already been programmed.
Engine start is enabled.
(The security light illuminates approx. 3 s and goes off.)
Engine start is disabled.
(The security light starts flashing/illuminating after an
error, such as verification failure or malfunction, is
detected, and then indicates the DTC for ten times
repeatedly.)
Result: NG
Result: NG
Result: OK
Result: OK
AUXILIARY KEY
(TRANSPONDER)
COIL ANTENNA
SECURITY LIGHT
INSTRUMENT CLUSTER
KEYLESS
CONTROL
MODULE
INSTRUMENT
CLUSTER
PCM
(3)
(2)
(1)
(4)
(4)
(2)
E5U914AS1017
SECURITY AND LOCKS [ADVANCED KEYLESS SYSTEM]
09–14A–21
09–14A
Immobilizer System Setting
• Some immobilizer system settings can be performed only using the WDS or equivalent. When using the WDS
or equivalent, first, security access must be requested. Obtain security access permission according to the
WDS or equivalent screen and then perform system procedures.
• When immobilizer system component parts (key, PCM, coil antenna, and keyless control module) are replaced,
the system must be reset as described below. Refer to the Workshop Manual for the detailed setting procedure.
End Of Sie
AUXILIARY KEY CONSTRUCTION
E5U091467000N04
• Keys for use with the immobilizer system have an
electronic communication device (transponder)
built into the key head that retains specific
electronic codes (key ID number).
End Of Sie
WDS or equivalent setting items
Contents
Programming an additional ignition key
Allows key ID number programming.
Ignition key ID number clearing
Clears all programmed key ID numbers and programs new key ID
numbers.
Customer spare key programming enable
“Additional ignition key programming” is enabled.
Note
• This is the default setting on new vehicles.
Customer spare key programming disable
“Additional ignition key programming” is disabled.
Note
• When only the WDS or equivalent must be used to program
key ID numbers, making a forged key by using two keys that
can start the engine is prevented. This function is for use by
rental car agencies or other companies with vehicle fleets.
Component part
Setting
Key addition
Key ID number of added key must be programmed. Key ID number programming can
be performed according to the following methods:
• Method for programming additional keys using two keys that can start the engine
• Method using the WDS or equivalent
Key clearing
The programmed key ID number can only be cleared using the WDS or equivalent.
When clearing key ID numbers using the WDS or equivalent, all the programmed key
ID numbers are cleared.
PCM replacement
• The key ID numbers for all keys that were being used must be programmed using
the WDS or equivalent. Two or more keys must be programmed.
Instrument cluster
• The key ID numbers for all keys that were being used must be programmed using
the WDS or equivalent. Two or more keys must be programmed.
Keyless control module replacement
• Card key and steering lock unit must be programmed.
• The key ID numbers for all keys that were being used must be programmed using
the WDS or equivalent. Two or more keys must be programmed.
Steering lock unit replacement
(including key replacement)
• Steering lock unit must be programmed.
• The key ID number must be programmed using the WDS or equivalent. Two or
more keys must be programmed.
Coil antenna replacement
Immobilizer system resetting is not necessary.
TRANSPONDER
E6U914AS1016
SECURITY AND LOCKS [ADVANCED KEYLESS SYSTEM]
09–14A–22
COIL ANTENNA CONSTRUCTION
E5U091467000N05
• Installed on the steering lock.
• Forms a magnetic field near the steering lock and
communicate to the key.
• Demodulates the received key signal and outputs
the signal to the keyless control module.
End Of Sie
SECURITY LIGHT CONSTRUCTION/OPERATION
E5U091467000N06
Construction
• Allows visual confirmation of immobilizer system operation.
• If any malfunction is detected in the immobilizer system, the malfunction location can be verified by the security
light illumination/flashing pattern.
Caution
• Always use the WDS or equivalent to verify DTCs even if the security light indicates a DTC. If the
security light itself has a malfunction, a DTC may not be indicated properly.
Operation
• When the immobilizer system is operating, the
security light flashes repeatedly 0.1 s every
approx. 2 s.
• When the immobilizer system is deactivated
normally, the security light illuminates for approx.
3 s and then goes out when the start knob is
turned to the ON position.
• If the immobilizer system is not deactivated
normally (malfunction detected by the malfunction
diagnosis function), the security light indicates a
DTC. When the start knob is turned to the ON
position, the security light flashes or illuminates
for 1 min in the following pattern:
— DTC 15 or lower: Flashes
— DTC 21: On
Note
• The security light indicates the DTC 10
times.
• If multiple DTCs that can be confirmed with
the security light are detected, only the DTC
with the lowest number of those detected will
be indicated by the security light.
End Of Sie
COIL ANTENNA
E6U914AS1017
ILLUMINATED
GOES OUT
APPROX. 2 S
APPROX. 0.1 S
C3U0914S011
ILLUMINATED
GOES OUT
APPROX. 3 S
C3U0914S012
EXAMPLES: DTC 12 DETECTED BY
THE MALFUNCTION DIAGNOSIS FUNCTION
ILLUMINATED
GOES OUT
APPROX. 1 MIN
DTC 12
C3U0914S013
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст