Mazda X-5. Manual — part 103
SECURITY AND LOCKS [ADVANCED KEYLESS SYSTEM]
09–14A–7
09–14A
Auto re-lock function
• The auto re-lock function automatically locks the doors if any of the following operations are performed within
approx. 30 s after the UNLOCK button of the card key is pressed, or after the request switch is pressed to
unlock the doors.
— A door or the trunk lid is opened.
— The auxiliary key is inserted in the ignition key cylinder.
— The start knob is pressed.
— The transmitter (card key) is operated. (If the UNLOCK button is pressed, the timer is reset.)
— A request switch is operated.
Out-of-area (reception area) autolock function
• When all doors are closed and the driver is out of the reception area carrying the card key, the doors are
automatically locked. (Initial setting is OFF.)
1. When all the following conditions are met and all doors are closed after any door or the trunk lid is open, the
keyless beeper sound is heard and the function starts operation. (The doors are not locked at this time.)
— The card key is not inside the vehicle.
— The card key is within the reception area outside the vehicle.
— The auxiliary key is not inserted in the ignition key cylinder.
— The start knob is in the LOCK position, and not being pressed.
2. After the operation has started, the card key is monitored within the reception area by the keyless antenna.
After about 2 s from where the card key has been determined to be out of the reception area, all lock actuators
activate to lock. If approx. 30 s have passed since the operation started, the doors also locks regardless of
whether the card key is within or out of the reception area.
3. The hazard warning light flashes once and keyless beep spund will be heard once at the same time the door
locks.
End Of Sie
SECURITY AND LOCKS [ADVANCED KEYLESS SYSTEM]
09–14A–8
ADVANCED KEYLESS START FUNCTION OPERATION
E5U091469000N03
• The advanced start function activates to start the engine by operating the start knob, and not by inserting the
key but by the driver carrying the card key while in the vehicle.
1. When the start knob is pressed, the keyless control module sends a request signal from the keyless antennas
(interior).
2. The card key receives the request signal, and sends back ID data.
3. The ID data is received by the keyless receiver, and sent to the keyless control module.
4. When the ID data is verified by the keyless control module and the card key is determined to be inside the
vehicle, the start knob of the steering lock unit is released. The keyless indicator light (green) in the instrument
cluster illuminates at the same time to indicate that the start knob is operable.
— If the ID verification is not acceptable (for reasons such as an unprogrammed card key, or card key battery
depletion or transmitter interference), the start knob is not released and the keyless warning light (red)
illuminates to indicate that the start knob is inoperable.
— For vehicles with the immobilizer system, ID verification is performed when the start knob is turned to the
ON position, and if the verification is acceptable, permission is given to start the engine.
5. Turn the start knob to the START position to start the engine.
End Of Sie
RECEPTION RANGE
(INTERIOR)
KEYLESS ANTENNA
KEYLESS ANTENNA
(INTERIOR, FRONT)
2
1
1
2
3
4
1
CARD KEY
KEYLESS RECEIVER
KEYLESS CONTROL
MODULE
KEYLESS ANTENNA
(INTERIOR, MIDDLE)
KEYLESS ANTENNA
(INTERIOR, REAR)
STEERING
LOCK UNIT
KEYLESS INDICATOR LIGHT
(GREEN) (ILLUMINATED)
KEYLESS WARNING LIGHT
(RED) (FLASH)
ID VERIFICATION OK
ID VERIFICATION NG
E5U914AS1007
SECURITY AND LOCKS [ADVANCED KEYLESS SYSTEM]
09–14A–9
09–14A
WARNING/GUIDANCE FUNCTION OPERATION
E5U091469000N04
• If the system is operated improperly, it warns the driver using the indicator light in the instrument cluster, buzzer
sound, and keyless beeper in the trunk compartment.
• The operation condition of the advanced keyless system is indicated by the indicator light and beeper sound to
guide user’s operation.
*1 : If the start knob is turned to the LOCK position with the card key out of the vehicle, the start knob is inoperable
(the engine cannot be restarted). For vehicles with the immobilizer system, the engine cannot be restarted by
turning the start knob from the ACC position to the START position even though the start knob has not been
turned to the LOCK position.
*2 : Stops flashing and goes out if the card key is detected inside the vehicle.
*3 : Stops flashing and goes out if the card key is detected inside the vehicle and door is opened.
End Of Sie
CUSTOMIZE FUNCTION OUTLINE
E5U091469000N05
• The settings of the following functions, and warning and guidance functions for the advanced keyless entry
system can be turned ON/OFF optionally.
• The WDS or equivalent is necessary for settings. Refer to the Workshop Manual for the detailed setting
procedure.
End Of Sie
Item
Operation condition
Keyless
buzzer
(outside
the vehicle)
Instrument cluster
Buzzer
(Interior)
Keyless
warning
light (red)
Keyless
indicator
light
(green)
Warning
Start knob not in
LOCK warning
Driver’s door is open with start knob in
ACC position
−
Continuous
Flashes
−
Card key out of
vehicle
warning
*1
Card key cannot be detected inside
vehicle with driver’s door open and
start knob not in LOCK position
−
Continuous
Flashes
*2
−
Card key cannot be detected inside
vehicle with all doors closed and start
knob not in LOCK position
Sounds 6
times
Flashes
*3
−
Card key cannot be detected inside
vehicle with start knob not in LOCK
position and under any condition other
than above
−
Flashes
*2
−
Card key left in
vehicle warning
Door/trunk lid is open with proper card
key inside vehicle and another card
key carried
Continuous
for 10 s
−
−
−
Door lock
inoperable
warning
Request switch is pressed with card
key carried and a door open or start
knob not in LOCK position
Sounds 6
times
−
−
−
Battery voltage
low indication
Card key battery voltage depleted
−
−
−
Flashes
(Approx. 30
s after IG
OFF)
Guidance
Start knob
operable
guidance
Start knob is operable (lock released)
when it is pressed
−
−
−
On
(Max. 3 s)
Start knob
inoperable
guidance
Start knob is inoperable (locked) when
it is pressed
−
−
Flashes
−
Lock/unlock
answer back
Doors are locked/unlocked with
normal/advanced keyless entry
function
Locked:
Once
Unlocked:
Twice
−
−
−
Function name
WDS or equivalent display
Initial
setting
Auto lock function (Out-of-area type)
Auto Lock
OFF
Keyless buzzer answer back
Answer Back Buzzer
OFF
Battery voltage low indication
Low Battery Warning
ON
SECURITY AND LOCKS [ADVANCED KEYLESS SYSTEM]
09–14A–10
ON-BOARD DIAGNOSYS SYSTEM OUTLINE (ADVANCED KEYLESS ENTRY SYSTEM)
E5U091469000N06
Special Features
• The keyless entry system has an on-board diagnostic function to facilitate system diagnosis.
• The on-board diagnostic function consists of the following functions: a malfunction detection function, which
detects overall malfunctions in the keyless entry system-related parts; a memory function, which stores
detected DTCs; a display function, which indicates system malfunctions by DTC display; and a PID/data
monitoring function, which reads out specific input/output signals.
• Using the WDS or equivalent, DTCs can be read out and cleared, and the PID/data monitoring function can be
activated.
End Of Sie
ON-BOARD DIAGNOSYS SYSTEM PID DATA/MONITOR FUNCTION OPERATION (ADVANCED KEYLESS
ENTRY SYSTEM)
E5U091469000N07
On-board Diagnostic Function
Malfunction detection function
• Detects overall malfunctions in the keyless entry system-related parts.
Display function
• If any malfunction is detected, the keyless warning light (red) in the instrument cluster illuminates to inform the
driver of a system malfunction.
Memory function
• Stores malfunctions in the keyless entry system-related parts detected by the malfunction detection function,
and the stored malfunction contents are not cleared even if the ignition switch is turned to the LOCK position or
the negative battery cable is disconnected.
DTC table
*
: With immobilizer system
PID/data monitor function
• The PID/data monitor function is used for optionally selecting input/output signal monitor items preset in the
keyless control module and reading them out in real-time.
• Use the WDS or equivalent to read the PID/data monitor.
DTC
System malfunction location
WDS or equivalent
display
B1342
Keyless control module internal malfunction
B1134
Unprogrammed card key
B2477
Configuration error
B1317
Keyless control module power supply voltage increases.
B1318
Keyless control module power supply voltage decreases
B2170
Push switch (Steering lock unit)
B1126
Steering lock unit internal malfunction
U0236
Steering lock unit communication system
B1093
Steering lock unit communication error
U0214
Keyless receiver
B1133
Keyless antenna (exterior, RF)
B1132
Keyless antenna (exterior, LF)
B1127
Keyless antenna (Interior, trunk)
B1128
Keyless antenna (Interior, rear)
B1131
Keyless antenna (exterior, rear)
B1129
Keyless antenna (Interior, middle)
B112A
Keyless antenna (Interior, front)
U0323
Communication error to instrument cluster
U0100
Communication error to PCM
U0073
Control module communication error
U2023
Error signal from CAN related module
B1681
*
No detected communication with the coil antenna.
B2103
*
Coil malfunction
B1213
*
Only one key ID number is programmed.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст