Mazda X-5. Manual — part 120
INSTRUMENTATION/DRIVER INFO.
09–22–7
09–22
End Of Sie
1H
b
c
a
P
R
N
D
M
2K
2V
SAS CONTROL MODULE
OIL PRESSURE SWITCH
SECURITY LIGHT
GEAR POSITION INDICATOR
: TO MICROCOMPUTER
CRUISE SET
INDICATOR LIGHT
CRUISE MAIN
INDICATOR LIGHT
BRAKE SYSTEM
WARNING LIGHT
ABS WARNING
LIGHT
SELECTOR INDICATOR
DRIVE CIRCUIT
AIR BAG SYSTEM
WARNING LIGHT
TURN INDICATOR
LIGHT (LH)
TURN INDICATOR
LIGHT (RH)
2A
BUCKLE SWITCH
(DRIVER'S SIDE)
BUCKLE SWITCH
(PASSENGER'S SIDE)
SEAT WEIGHT
SENSOR
CONTROL
MODULE
IG1
B+
2I
2G
TURN SWITCH
HAZARD WARNING
SWITCH
FLASHER
CONTROL MODULE
TURN LIGHT
(LH)
TURN LIGHT
(RH)
2F
KEYLESS CONTROL MODULE
KEYLESS
CONTROL
MODULE
2U
KEYLESS
INDICATOR LIGHT
KEYLESS
WARNING LIGHT
BRAKE FLUID
LEVEL SENSOR
1D
PARKING BRAKE SWITCH
2M
TIRE PRESSURE
WARNING LIGHT
FLAT TIRE
WARNING LIGHT
WITH ADVANCED
KEYLESS SYSTEM OR
KEYLESS ENTRY SYSTEM
KEYLESS
RECEIVER
WITH TPMS
KEYLESS CONTROL MODULE
WITH ADVANCED
KEYLESS SYSTEM
WITHOUT ADVANCED
KEYLESS SYSTEM AND
KEYLESS ENTRY SYSTEM
E5U922ZS5003
INSTRUMENTATION/DRIVER INFO.
09–22–8
INPUT/OUTPUT CHECK MODE OUTLINE
E5U092255430N05
• The microcomputer built into instrument cluster detects the quality of input signals and individual parts.
• Input/output check mode has both input circuit inspection and individual part inspection functions.
End Of Sie
INPUT/OUTPUT CHECK MODE OPERATION
E5U092255430N06
Operation procedure
• Refer to Mazda MX-5 Workshop Manual.
Input circuit check
• When the parts listed in the chart are operated and a signal is output to the instrument cluster, the built-in
microcomputer determines the operability of the input circuit based on that signal.
Individual circuit check
• By operating the parts listed in the chart, the built-in microcomputer determines the operability of the individual
parts.
Check
code
Parts sending input signal
01
SAS control module
04
Door switch
08
TNS relay
22
Fuel gauge sender unit
31
Key reminder switch (built into the ignition
switch or steering lock unit)
59
Fuel system signal
LCD
SAS CONTROL
MODULE
TNS
RELAY
FUEL GAUGE
SENDER UNIT
KEY REMINDER
SWITCH
PCM
INSTRUMENT
CLUSTER
MICROCOMPUTER
DOOR
SWITCH
E5U922ZS5004
Check
code
Parts sending input signal
12
Speedometer
13
Tachometer
14
Buzzer
16
Fuel-level warning light
18
Ignition key illumination output
23
Fuel gauge
25
Water temperature gauge
26
LCD, warning and indicator light
28
Oil pressure gauge
57
Panel light control
INSTRUMENTATION/DRIVER INFO.
09–22–9
09–22
PID/Data Monitor and Record
• The PID/data monitoring items for the instrument cluster is as shown in following the table:
Monitor item table
—: Not applicable
Odometer-data Transfer
• If all the following conditions are met, the odometer data (total traveled distance) in the previous instrument
cluster is automatically transferred to a new instrument cluster during the configuration. If any of the conditions
are not met, odometer-data transfer cannot be performed.
Previous instrument cluster
— No malfunction (Configuration data can be read using the WDS or equivalent.)
New instrument cluster
— Odometer display is less than 100 km
— Odometer has no malfunction
Note
• If the odometer display of a new instrument cluster is 100 km or more, an error is displayed on the WDS
after the configuration is completed. In this case, the configuration data for items other than the odometer
are transferred to a new instrument cluster.
End Of Sie
LCD
SPEEDOMETER
TACHOMETER
BUZZER
WARNING AND
INDICATOR LIGHT
FUEL
GAUGE
WATER
TEMPERATURE
GAUGE
ILLUMINATION
LIGHT BULB
INSTRUMENT CLUSTER
MICROCOMPUTER
OIL PRESSURE
GAUGE
E5U922ZS5005
Monitor item
Input-output signal/part
name
Unit/State
Terminal
IC_DTC_CNT
Number of continuous DTCs
—
—
IC_ECT
Water temperature gauge
°F
°C
1J, 1L
IC_NUMKEYS
Number of key ID numbers
registered with the vehicle
—
—
IC_ODO_CNT
Odometer
m
1J, 1L
IC_SPDMTR
Speedometer
MPH
KPH
IC_TACHO
Tachometer
RPM
IC_VPWR
Power supply voltage
V
1C
INSTRUMENTATION/DRIVER INFO.
09–22–10
LIGHTS-ON REMINDER WARNING ALARM OUTLINE
E5U092255430N07
• Warns the driver that the headlights or TNS are on when the driver-side door is opened.
End Of Sie
LIGHTS-ON REMINDER WARNING ALARM CONSTRUCTION/OPERATION
E5U092255430N08
System Wiring Diagram
Operation
• The buzzer in the instrument cluster sounds
continuously when all the following three
conditions are met:
— The ignition switch is in the LOCK or ACC
position.
— The headlight switch is in the TNS or
headlight position.
— The driver-side door is open (driver-side door
switch is on).
End Of Sie
SEAT BELT WARNING ALARM OUTLINE
E5U092255430N09
• Warns the driver that the seat belt (driver-side or passenger-side) is unfastened.
End Of Sie
SEAT BELT WARNING ALARM CONSTRUCTION/OPERATION
E5U092255430N10
System Wiring Diagram
Operation
• The buzzer in the instrument cluster sounds for 6
s when all the following two conditions are met:
— After the ignition switch is turned to ON
position.
— The seat belt (driver-side) is unfastened
(buckle switch is off).
• The buzzer in the instrument cluster sounds for 93
s when all the following two conditions are met:
— The seat belt (driver-side or passenger-side)
is unfastened (driver-side: buckle switch is off,
passenger-side: buckle switch is off and seat
weight sensor detects passenger).
— The vehicle speed is 20 km/h {12.4 mph} or
more.
End Of Sie
IG1
B+
1G
1E
2E
1C
B+
1B
INSTRUMENT
CLUSTER
TNS
RELAY
TO LIGHT
SWITCH
BUZZER
MICROCOMPUTER
DOOR SWITCH
(DRIVER-SIDE)
AND
E5U922ZS5006
1G
1E
2A
1C
IG1
B+
AND
INSTRUMENT CLUSTER
MICROCOMPUTER
TIMER
BUZZER
SAS CONTROL
MODULE
BUCKLE SWITCH (DRIVER-SIDE)
BUCKLE SWITCH (PASSENGER-SIDE)
SEAT WEIGHT SENSOR
CONTROL MODULE
SEAT WEIGHT
SENSOR
E5U922ZS5007
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст