Mazda MX-5 Miata / Grand Touring. Manual — part 8

PASSENGER AIR BAG DEACTIVATION (PAD) SWITCH
REMOVAL/INSTALLATION

1. Remove the battery cover.

2. Disconnect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION [LF] .)

3. Remove the side panel. (See SIDE PANEL REMOVAL/INSTALLATION .)

4. Disconnect the connector.

5. Remove the PAD switch.

Fig. 26: View Of Passenger Air Bag Deactivation (PAD) Switch
Courtesy of MAZDA MOTORS CORP.

6. Install in the reverse order of removal.

7. Turn the ignition switch to the ON position.

8. Verify that the air bag system warning light illuminates for approx. 6 s and goes out.



If the air bag system warning light does not operate normally, refer to RESTRAINTS -- ON-
BOARD DIAGNOSTIC system (air bag system) and perform inspection of the system.

PASSENGER AIR BAG DEACTIVATION (PAD) SWITCH INSPECTION

1. Remove the PAD switch. (See PASSENGER AIR BAG DEACTIVATION (PAD) SWITCH

REMOVAL/INSTALLATION .)

2008 Mazda MX-5 Miata Grand Touring

2008 RESTRAINTS Air Bag System - MX-5 Miata

2. Verify that the continuity between the PAD switch terminals is as indicated in Fig. 27 .



If not as indicated in Fig. 27 , replace the PAD switch.

Fig. 27: PAD Switch Continuity Table
Courtesy of MAZDA MOTORS CORP.

Fig. 28: Inspecting Passenger Air Bag Deactivation (PAD) Switch Connector Terminals
Courtesy of MAZDA MOTORS CORP.

2008 Mazda MX-5 Miata Grand Touring

2008 RESTRAINTS Air Bag System - MX-5 Miata

SIDE AIR BAG SENSOR REMOVAL/INSTALLATION

1. Turn the ignition switch to the LOCK position.

2. Remove the battery cover.

3. Disconnect the negative battery cable and wait for 1 min or more . (See BATTERY

REMOVAL/INSTALLATION [LF] .)

4. Remove the quarter trim. (See QUARTER TRIM REMOVAL/INSTALLATION .)

5. Remove the scuff plate. (See SCUFF PLATE REMOVAL/INSTALLATION .)

6. Remove the tire house trim. (See TIRE HOUSE TRIM REMOVAL/INSTALLATION .)

7. Remove in the order indicated in Fig. 29 .

Fig. 29: View Of Side Air Bag Sensor & Components
Courtesy of MAZDA MOTORS CORP.

WARNING:



Handling the side air bag sensor improperly can accidentally
operate (deploy) the air bag module, which may seriously injure you.
Read the air bag system service warnings and cautions before
handling the side air bag sensor. (See AIR BAG SYSTEM SERVICE
WARNINGS .) (See AIR BAG SYSTEM SERVICE CAUTIONS .)

2008 Mazda MX-5 Miata Grand Touring

2008 RESTRAINTS Air Bag System - MX-5 Miata

8. Install in the reverse order of removal.

9. Turn the ignition switch to the ON position and hold for 5 s or more .

10. Verify that the air bag system warning light illuminates for approx. 6 s and goes out.



If the air bag system warning light does not operate normally, refer to RESTRAINTS -- ON-
BOARD DIAGNOSTIC system (air bag system) and perform inspection of the system.

CLOCK SPRING REMOVAL/INSTALLATION

1. Remove the battery cover.

2. Disconnect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION [LF] .)

3. Remove the following parts:

1. Driver-side air bag module (See DRIVER-SIDE AIR BAG MODULE

REMOVAL/INSTALLATION .)

2. Steering wheel (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION .)

3. Column cover (See COLUMN COVER REMOVAL/INSTALLATION .)

4. Remove in the order indicated in Fig. 30 .

Fig. 30: View Of Clock Spring Components

2008 Mazda MX-5 Miata Grand Touring

2008 RESTRAINTS Air Bag System - MX-5 Miata