Mazda Transaxle A65M–R. Manual — part 3
FUNDAMENTAL PROCEDURES
GI–7
GI
ARRANGEMENT OF PARTS
AME201400004M05
•
All disassembled parts should be carefully
arranged for reassembly.
•
Be sure to separate or otherwise identify the parts
to be replaced from those that will be reused.
End Of Sie
CLEANING OF PARTS
AME201400004M06
•
All parts to be reused should be carefully and
thoroughly cleaned in the appropriate method.
Warning
••••
Using compressed air can cause dirt and
other particles to fly out causing injury to
the eyes. Wear protective eye wear
whenever using compressed air.
End Of Sie
REASSEMBLY
AME201400004M07
•
Standard values, such as torques and certain
adjustments, must be strictly observed in the
reassembly of all parts.
•
If removed, these parts should be replaced with
new ones:
— Oil seals
— Gaskets
— O-rings
— Lockwashers
— Cotter pins
— Nylon nuts
•
Depending on location:
— Sealant and gaskets, or both, should be
applied to specified locations. When sealant
is applied, parts should be installed before
sealant hardens to prevent leakage.
— Oil should be applied to the moving
components of parts.
— Specified oil or grease should be applied at
the prescribed locations (such as oil seals)
before reassembly.
End Of Sie
WGIWXX0029E
WGIWXX0030E
WGIWXX0031E
WGIWXX0032E
GI–8
FUNDAMENTAL PROCEDURES
ADJUSTMENT
AME201400004M08
•
Use suitable gauges and/or testers when making
adjustments.
End Of Sie
RUBBER PARTS AND TUBING
AME201400004M09
•
Prevent gasoline or oil from getting on rubber
parts or tubing.
End Of Sie
HOSE CLAMPS
AME201400004M10
•
When reinstalling, position the hose clamp in the
original location on the hose and squeeze the
clamp lightly with large pliers to ensure a good fit.
End Of Sie
TORQUE FORMULAS
AME201400004M11
•
When using a torque wrench-SST or equivalent
combination, the written torque must be
recalculated due to the extra length that the SST
or equivalent adds to the torque wrench.
Recalculate the torque using the following
formulas. Choose the formula that applies to you.
A : The length of the SST past the torque wrench drive
L : The length of the torque wrench
End Of Sie
WGIWXX0033E
WGIWXX0034E
WGIWXX0035E
Torque Unit
Formula
NВ·m
NВ·m
Г—
[L/(L+A)]
kgfВ·m
kgfВ·m
Г—
[L/(L+A)]
kgfВ·cm
kgfВ·cm
Г—
[L/(L+A)]
ftВ·lbf
ftВ·lbf
Г—
[L/(L+A)]
inВ·lbf
inВ·lbf
Г—
[L/(L+A)]
WGIWXX0036E
FUNDAMENTAL PROCEDURES, ELECTRICAL SYSTEM
GI–9
GI
VISE
AME201400004M12
•
When using a vise, put protective plates in the
jaws of the vise to prevent damage to parts.
End Of Sie
CONNECTORS
AME201700006M01
Data Link Connector
•
Insert the probe into the service hole when
connecting a jumper wire to the data link
connector.
Caution
••••
Inserting a jumper wire probe into the
data link connector terminal may damage
the terminal.
Disconnecting Connectors
•
When disconnecting connector, grasp the
connectors, not the wires.
•
Connectors can be disconnected by pressing or
pulling the lock lever as shown.
WGIWXX0037E
ELECTRICAL SYSTEM
X3U000WAY
WGIWXX0041E
WGIWXX0042E
GI–10
ELECTRICAL SYSTEM
Locking Connector
•
When locking connectors, listen for a click
indicating they are securely locked.
Inspection
•
When a tester is used to inspect for continuity or
measuring voltage, insert the tester probe from
the wiring harness side.
•
Inspect the terminals of waterproof connectors
from the connector side since they cannot be
accessed from the wiring harness side.
Caution
••••
To prevent damage to the terminal, wrap
a thin wire around the tester probe before
inserting into terminal.
Terminals
Inspection
•
Pull lightly on individual wires to verify that they
are secured in the terminal.
X3U000WB1
WGIWXX0044E
WGIWXX0045E
WGIWXX0064E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст