Mazda 5. Manual — part 37
05–17–68
AUTOMATIC TRANSAXLE
Snap ring sizes
(9) Install the selected snap ring and perform steps (2) to (7) again. Verify that the calculated value satisfies the
clearance specification.
13. Inspect the 3–4 clutch operation.
(1) Install the 3–4 clutch drum to the end cover.
(2) Inspect the 3–4 clutch operation by applying
compressed air as shown.
Air pressure
392—441 kPa {4.0—4.5 kgf/cm
2
, 57—63 psi}
14. Install the 3–4 clutch component to the 2–4 brake
drum.
15. Apply petroleum jelly to the bearing, and secure it
onto the 3–4 clutch component.
16. Install the 3–4 clutch hub.
17. Apply petroleum jelly to the bearing, and secure it
onto the 3–4 clutch hub as shown in the figure.
18. Install the rear sun gear plate onto the 2–4 brake
drum.
19. Install the snap ring.
End Of Sie
FRONT INTERNAL GEAR ONE-WAY CLUTCH COMPONENT DISASSEMBLY/ASSEMBLY
B3E051719500A03
1. Perform the preinspection before disassembly.
(See 05–17–127 Front Internal Gear and One-Way Clutch Component.)
2. Disassemble in the order indicated in the table.
Range mm {in}
Snap ring sizes mm {in}
Drive plate part number:FN11 19 370
Drive plate part number:FNE1 19 370
2.250—2.450 {0.089—0.096}
2.350—2.550 {0.093—0.100}
1.2 {0.047}
2.450—2.650 {0.096—0.104}
2.550—2.750 {0.100—0.108}
1.4 {0.055}
2.650—2.850 {0.104—0.112}
2.750—2.950 {0.108—0.116}
1.6 {0.063}
2.850—3.050 {0.112—0.120}
2.950—3.150 {0.116—0.124}
1.8 {0.071}
3.050—3.250 {0.120—0.128}
3.150—3.350 {0.124—0.132}
2.0 {0.079}
3.250—3.450 {0.128—0.136}
3.350—3.550 {0.132—0.140}
2.2 {0.087}
3-4 CLUTCH FLUID PASSAGE
B3E0517A262
B3E0517A264
SNAP RING
3-4
CLUTCH HUB
BEARING
REAR SUN GEAR PLATE
B3E0517A265
AUTOMATIC TRANSAXLE
05–17–69
05
3. Assemble in the reverse order of disassembly.
.
One-Way Clutch Retainer Disassembly Note
• Remove the one-way clutch retainer using a flathead screwdriver, etc. as shown in the figure.
Assembly Procedure
1. Install the snap ring.
5
4
3
1
2
2
ATF
B3E0517A119
1
One-way clutch retainer
(See 05–17–69 One-Way Clutch Retainer
Disassembly Note.)
2
Side race
3
One-way clutch
4
Snap ring
5
Front internal gear
FRONT INTERNAL GEAR
ONE-WAY CLUTCH RETAINER
B3E0517A120
05–17–70
AUTOMATIC TRANSAXLE
2. Install the one-way clutch to the front internal gear
in the direction of the arrow (on the one-way
clutch) as shown in the figure.
3. Install the side race.
4. Install the one-way clutch retainer.
End Of Sie
BAND SERVO DISASSEMBLY/ASSEMBLY
B3E051719500A04
1. Disassemble in the order indicated in the table.
FRONT INTERNAL GEAR
SIDE RACE
ARROW
SIDE RACE
ONE-WAY CLUTCH
LOW-RESISTANCE TYPE
STANDARD TYPE
SIDE RACE
ARROW
MARKING
FRONT INTERNAL GEAR
SIDE RACE
ONE-WAY CLUTCH
CDA517ZAA002
AUTOMATIC TRANSAXLE
05–17–71
05
2. Assemble in the reverse order of disassembly.
Assembly Procedure
1. Measure the spring free length.
Specification
• If not as specified, replace the spring.
2. Install the servo return spring to the transaxle case.
1
Servo retainer
2
O-ring
3
Servo piston
4
Servo return spring
5
Band strut
6
2–4 brake band
5
4
3
1
2
6
R
ATF
ATF
10.8—13.7 N·m {110—140 kgf·cm, 95.5—121 in·lbf}
B3E0517A122
Outer
diameter
mm {in}
Free length
mm {in}
No. of
coils
Wire diameter
mm {in}
34.0 {1.340}
36.4 {1.430}
2.5
4.0 {0.160}
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст