Mazda MPV Facelift. Manual — part 7
HVAC Fuel
Fired
Heater
Service Training
25
Fuel Fired Heater
On-board diagnostic system
•
A self test/combustion test procedure, and lockout reset procedure have been added
•
PID and simulation item tables have been added to the workshop manual
•
A symptom troubleshooting index for the fuel fired heater has been added to the
workshop manual.
Combustion test
1. Connect the SST (WDS or equivalent) to the vehicle DLC-2 16-pin connector
2. Select the "Supplemental Heater Test" in the "Supplemental Heater Menu" of the
"Guided Diagnosis" function
3. Perform the KOEO Self Test/Combustion Test
NOTE: If the water heater unit is operating, the water heater unit will reject the test command.
Perform the DTC reading procedure after the water heater unit stops operating
Lockout reset (using WDS)
1. Connect the SST (WDS or equivalent) to the vehicle DLC-2 16-pin connector
2. Select "CLR_LOCKOUT" and "LOCKOUT
3. Turn "CLR_LOCKOUT" to ON using the simulation function
4. Verify that the "LOCKOUT" reading changes to "Unlocked"
Lockout reset (not using WDS)
For factory equipped water heater unit
1. Turn the ignition switch to the OFF position
2. Remove the W.HEAT 40 A fuse from the main fuse block for more than 5 seconds
3. Re-install the W.HEAT 40 fuse
For vehicles with a transmitter or timer
1. Turn the ignition switch to the OFF position
2. Remove the power supply 40 A fuse from the heater wiring harness for approx. 3
seconds
3. Re-install the power supply 40 A fuse
4. Press and hold down the ON switch of the transmitter or timer for approx. 3 seconds
5. Remove the power supply 40 A fuse from the heater wiring harness for approx. 3
seconds
6. Re-install the power supply 40 A fuse
Fuel Fired Heater
HVAC
26 Service
Training
On-board diagnostic system (continued)
PID monitor
PID Name
Definition
Unit/Condition
CCNTFFH
Number of continuous codes)
-
ECT
Engine coolant temperature
°C
°F
VPWR_FFH
Module supply voltage
V
VPWR_LMT
Low voltage threshold
V
FAN Fan
control
%
GPD
Glow plug duty cycle
%
BLOWRMTR Blower
motor
On/Off
FP Fuel
pump
On/Off
WATER_PMP
Water pump
On/Off
GLOW PLUG
Glow plugs
On/Off
COMB_FAN
Combustion air fan
On/Off
LOCKOUT Heater
lockout
Lock/Unlock
FS
Flame sensor
On/Off
HEATER Heater
status
Inactive/Active
HEATER_SW Heater
activation
switch
Inactive/Active
Simulation Test Item Table
Item Definition
Operation
CLR_LOCKOUT
Heater lockout mode clearing command
On/-
FUEL_PRIME
Fuel pump priming command
(The fuel pump is activated for 5 seconds.)
On/-
Body and Accessories
Service Training
27
Body and Accessories
Features
•
The headlamp design has been changed
•
Seven new body colours have been introduced: Blue Pacific Mica, Gloaming Silver,
Razor Blue, Nordic Green Mica, Titanium Grey II Mica, Arctic White, Snowflake White
Pearl
•
A three spoke steering wheel has been adopted
•
Karakuri seats are available on some versions
•
Driver information system now available for diesel vehicles
Body and Accessories
28 Service
Training
Multiplex communication system
•
A high-speed CAN multiplex communication system, as well as the existing ISO 9141
communication system have been adopted on diesel engine vehicles.
CAN
•
The following modules are connected to the CAN bus:
–
PCM
–
ABS/TCS module
–
Fuel fired heater
–
DLC-2
CAN diagram MPV
1
PCM 4
DLC-2
2
ABS/TCS module
5
Twisted wires
3
Fuel fired heater
ISO 9141
•
The following items are connected to the ISO 9141 network:
–
ABS/TCS module
–
DLC-2
–
DLC-1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст