Mazda MX-5 Miata (1997+). Manual — part 94
Fig. 3: Exploded View Of Rear Lower Arm Assembly
Courtesy of MAZDA MOTORS CORP.
UPPER ARM
Removal
Raise and support vehicle. Remove rear wheel assembly. Remove upper arm-to-crossmember bolts. Remove
upper arm-to-knuckle bolts. Remove upper arm. Inspect arm for damage, cracks and deformation. Check for
damaged or worn bushings.
Installation
To install, reverse removal procedure. Tighten all nuts/bolts to specification with vehicle resting on ground and
suspension unloaded. See TORQUE SPECIFICATIONS . Adjust rear wheel alignment. See
SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT.
1997 Mazda MX-5 Miata
1997, 1999-2000 SUSPENSION Rear - Miata
STABILIZER BAR
Removal
Raise and support vehicle. Remove rear wheel assembly. Remove stabilizer bar-to-crossmember bolts, brackets
and bushings. See Fig. 4 . Remove stabilizer bar control link-to-lower arm nut and bolt. Remove stabilizer bar
and control link from vehicle. Separate stabilizer bar from control link. Inspect stabilizer bar and components
for damage, cracks and deterioration.
Installation
To install, reverse removal procedure. Ensure bushing is aligned with White line on stabilizer. Tighten nuts and
bolts to specification with vehicle resting on ground and suspension unloaded. See TORQUE
SPECIFICATIONS .
Fig. 4: Exploded View Of Rear Stabilizer Bar & Control Link
1997 Mazda MX-5 Miata
1997, 1999-2000 SUSPENSION Rear - Miata
Courtesy of MAZDA MOTORS CORP.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS
Application
Ft. Lbs. (N.m)
ABS Speed Sensor Harness & Bracket Bolts
12-16 (16-22)
Caliper Assembly-To-Knuckle Bolt
37-50 (50-68)
Drive Axle Lock Nut
1997
160-216 (216-294)
1999 & 2000
174-235 (236-318)
Lower Arm-To-Crossmember Nuts
54-70 (73-95)
Lower Arm-To-Knuckle Nut
46-55 (63-75)
Shock Piston Rod Nut
1997
22-27 (30-37)
Shock-To-Body Nuts
22-26 (30-35)
Stabilizer Bar Bracket Bolts
15-20 (20-28)
Stabilizer Link Bolts
1997
27-39 (37-53)
1999 & 2000
32-44 (44-60)
Strut-To-Lower Arm Bolt
54-68 (73-93)
Upper Arm-To-Crossmember Nuts
1997
34-49 (47-66)
1999 & 2000
40-56 (54-76)
Upper Arm-To-Knuckle Bolt
1997
34-49 (47-66)
1999 & 2000
40-56 (54-76)
Wheel Lug Nuts
66-86 (89-117)
1997 Mazda MX-5 Miata
1997, 1999-2000 SUSPENSION Rear - Miata
STARTER - DIRECT DRIVE
1997 STARTING & CHARGING SYSTEMS Mazda - Starters - Direct Drive
DESCRIPTION & OPERATION
Direct drive starter is a conventional 12-volt, 4-pole, brush-type starter. The integral solenoid is attached to the
drive housing. The overrunning clutch pinion drive is mounted directly on end of armature shaft drive.
TROUBLE SHOOTING
ON-VEHICLE TESTING
* PLEASE READ FIRST *
CIRCUIT TESTING
If starter does not operate, check voltage at starter "S" terminal with ignition switch in START position (and
clutch depressed on M/T). See Fig. 1 . If voltage is greater than 8 volts, repair or replace starter as required. If
voltage is 8 volts or less, check ignition switch, park/neutral switch (A/T), interlock switch (M/T) and wiring.
NOTE:
See TROUBLE SHOOTING article in GENERAL INFORMATION.
NOTE:
On all models with anti-theft system, obtain code number and deactivate audio
anti-theft system before disconnecting battery.
NOTE:
Before testing, ensure battery is fully charged, battery cables and terminals are
clean and tight, and engine grounds are good.
1997 Mazda MX-5 Miata
STARTER - DIRECT DRIVE 1997 STARTING & CHARGING SYSTEMS Mazda - Starters - Direct Drive
1997 Mazda MX-5 Miata
STARTER - DIRECT DRIVE 1997 STARTING & CHARGING SYSTEMS Mazda - Starters - Direct Drive
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст