Mazda Automatic Transaxle JA5A-EL. Manual — part 37
AUTOMATIC TRANSAXLE
K153
K1
37. Install a new anchor end bolt.
Tightening torque
6494 N·m {6.59.5 kgf·m, 4769 ft·lbf}
38. Adjust the brake band.
(1) Set the SST to prevent the brake band piston
from turning.
(2) Tighten the piston stem.
Tightening torque
4.06.0 N·m
{0.400.60 kgf·m, 2.94.3 ft·lbf}
(3) Loosen the piston stem 5 rotations.
(4) Tighten the lock nut while preventing the
piston stem from turning.
Tightening torque
3950 N·m {4.15.2 kgf·m, 4051 ft·lbf}
39. Position the reduction brake band servo.
40. Install the snap ring which secures the reduction
brake band servo.
41. Install the sun gear on the direct clutch drum.
AMU0517A134
AMU0517A135
AMU0517A018
AMU0517A017
K154
AUTOMATIC TRANSAXLE
42. Install the reduction gear component.
43. Apply petroleum jelly to new seal rings, then
assemble them to the input shaft.
44. Install the input shaft.
Caution
•••• If the oil pump gasket is bent or
scratched, do not reuse it.
45. Position the oil pump gasket.
46. Install the oil pump component and tighten bolts.
Tightening torque
1922 N·m
{1.92.2 kgf·m, 1416 ft·lbf}
47. Apply a coat of ATF to a new O-ring, then install it
to the input shaft.
48. Install the vehicle speedometer sensor (VSS).
Tightening torque
6.98.8 N·m
{0.700.90 kgf·m, 5.16.5 ft·lbf}
49. Connect the VSS connector.
50. Install the harness bracket.
Tightening torque
6.98.8 N·m
{0.700.90 kgf·m, 5.16.5 ft·lbf}
51. Install the intermediate sensor.
Tightening torque
6.98.8 N·m
{0.700.90 kgf·m, 5.16.5 ft·lbf}
52. Connect the intermediate sensor connector.
AMU0517A016
AMU0517A015
AMU0517A014
AMU0517A013
AMU0517A012
AUTOMATIC TRANSAXLE
K155
K1
53. Install the magnets.
54. Install the transaxle fluid temperature (TFT)
sensor.
Tightening torque
6.98.8 N·m
{0.700.90 kgf·m, 5.16.5 ft·lbf}
55. Install the oil strainer.
Tightening torque
1922 N·m
{1.92.2 kgf·m, 1416 ft·lbf}
56. Install the differential component.
57. Install the converter housing.
Tightening torque
2730 N·m {2.83.1 kgf·m, 2022 in·lbf}
Caution
•••• Be careful not to scratch the mating
surface of the converter housing and
transaxle case.
58. Install the terminal component.
59. Install the bracket to the coupling connector.
Note
• If the seal ring is misplaced or scratched, do
not reuse it.
60. Apply a coat of ATF to new seal rings, then install
them to the transaxle case.
AMU0517A011
AMU0517A010
AMU0517A009
AMU0517A008
K156
AUTOMATIC TRANSAXLE
61. Install the control valve body to the transaxle
case.
(1) Set the manual shaft at L renge.
(2) Position the manual valve so that it protrudes
from the control valve body end by 3.0 mm.
(3) Install the control valve body while holding the
manual valve in the position.
(4) Move the manual shaft , when verify in
conjunction with manual valve.
62. Tighten the bolts which secure the control valve
body to the transaxle case.
(1) Tighten the bolt A. (10 pieces)
Tightening torque
6.98.8 N·m
{0.700.90 kgf·m, 5.16.5 ft·lbf}
(2) Tighten the bolt B. (1 pieces)
Tightening torque
6.98.8 N·m
{0.700.90 kgf·m, 5.16.5 ft·lbf}
63. Tighten the bracket on the coupling connector.
64. Connect the coupling connectors between the
solenoid valves and terminal component.
65. Apply a light coat of silicone sealant to the contact
surfaces of the control valve body cover and
transaxle case.
66. Install the control valve body cover.
Tightening torque
6.98.8 N·m
{0.700.90 kgf·m, 5.16.5 ft·lbf}
67. Remove the transaxle from the transaxle stand.
AMU0517A186
AMJ5614A072
AMU0517A005
AMU0517A184
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст