RAM 3500 (2022 year). Manual in english — page 25
396
SERVICING AND MAINTENANCE
Maintenance Log and Service Chart (Diesel Engines)
Noise Systems Maintenance Chart and Service Log — Insert Month, Day, Year under column mileage closest to the mileage at which service was
performed.
MILES
7,500
15,000
22,500
30,000
37,500
45,000
52,500
60,000
KILOMETERS
12,000
24,000
36,000
48,000
60,000
72,000
84,000
96,000
Exhaust system-inspect
Air cleaner assembly-inspect
ODOMETER READING
PERFORMED BY
PERFORMED AT
MILES
67,500
75,000
82,500
90,000
97,500
105,000
112,500
120,000
KILOMETERS
108,000
120,000
132,000
144,000
156,000
168,000
180,000
192,000
Exhaust system-inspect
Air cleaner assembly-inspect
ODOMETER READING
PERFORMED BY
PERFORMED AT
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
397
FUSES
General Information
The fuses protect electrical systems against
excessive current.
When a device does not work, you must check the
fuse element inside the blade fuse for a break/
melt.
Also, please be aware that using power outlets for
extended periods of time with the engine off may
result in vehicle battery discharge.
Blade Fuses
Power Distribution Center
The Power Distribution Center is located in the
engine compartment near the battery. This center
contains cartridge fuses, micro fuses, relays, and
circuit breakers. A description of each fuse and
component may be stamped on the inside cover,
otherwise the cavity number of each fuse is
stamped on the inside cover that corresponds to
the following chart.
WARNING!
When replacing a blown fuse, always use an
appropriate replacement fuse with the same
amp rating as the original fuse. Never replace
a fuse with another fuse of higher amp rating.
The use of a fuse with a rating other than indi
-
cated may result in a dangerous electrical
system overload. If a properly rated fuse
continues to blow, it indicates a problem in the
circuit that must be corrected. Never replace a
blown fuse with metal wires or any other mate
-
rial. Do not place a fuse inside a circuit
breaker cavity or vice versa. Failure to use
proper fuses may result in serious personal
injury, fire and/or property damage.
Before replacing a fuse, make sure that the
ignition is off and that all the other services
are switched off and/or disengaged.
If the replaced fuse blows again, contact an
authorized dealer.
If a general protection fuse for safety systems
(air bag system, braking system), power unit
systems (engine system, transmission
system) or steering system blows, contact an
authorized dealer.
CAUTION!
If it is necessary to wash the engine
compartment, take care not to directly hit the
fuse box, and the windshield wiper motors with
water.
1 — Fuse Element
2 — Blade Fuse with a good/functional fuse
element
3 — Blade fuse with a bad/not functional fuse
element (blown fuse)
CAUTION!
When installing the power distribution center
cover, it is important to ensure the cover is
properly positioned and fully latched. Failure
to do so may allow water to get into the power
distribution center and possibly result in an
electrical system failure.
If it is necessary to wash the engine compart
-
ment, take care not to directly hit the fuse box,
and the windshield wiper motors with water.
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
398
SERVICING AND MAINTENANCE
Power Distribution Center Location
Cavity
Cartridge Fuse
Micro Fuse
Description
* If Equipped
F01
–
–
Spare
F02
60 Amp Yellow
–
ABS Pump Mtr
F03
60 Amp Yellow
–
Rad Fan HI/Lo *
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
399
F04
50 Amp Red
–
400W Inverter
F05
40 Amp Green
–
Air Suspension Comp
F06
40 Amp Green
–
STOM
F07
40 Amp Green
–
Starter Solenoid
F08
20 Amp Blue
–
NOX Sensor *
F09
40 Amp Green
–
Diesel / Fuel Heater *
F09
30 Amp Pink
–
Gas / Brake Vacuum Pump *
F10
40 Amp Green
–
CBC #2 / Ext Lights
F11
40 Amp Green
–
Brake SYS MOD ECU& Valves
F12
40 Amp Green
–
CBC #3 / Pwr Locks
F13
40 Amp Green
–
HVAC Blwr Mtr
F14
40 Amp Green
–
CBC #4 / Ext Light
F15
30 Amp Pink
–
Power Side Step *
F16
30 Amp Pink
–
Smart-Bar Module *
F17
30 Amp Pink
–
Winch *
F18
–
–
Spare
F19
30 Amp Pink
–
Diesel SCR Feed *
F20
30 Amp Pink
–
Passenger Door Mod
F21
30 Amp Pink
–
DTCM
F22
20 Amp Blue
–
Gas - ECM *
Cavity
Cartridge Fuse
Micro Fuse
Description
* If Equipped
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
400
SERVICING AND MAINTENANCE
F22
25 Amp White
–
Diesel - PCM *
F23
30 Amp Pink
–
CBC #1 / Int Light
F24
30 Amp Pink
–
Driver Door Mod
F25
30 Amp Pink
–
FT Wiper
F26
–
–
Spare
F27
–
–
Spare
F28
20 Amp Blue
–
TRLR Tow B/U
F29
20 Amp Blue
–
TRLR TOW PARK
F30
30 Amp Pink
–
TRLR Tow
F31
–
–
Spare
F32
–
–
Spare
F33
20 Amp Blue
–
Trans Control Mod *
F34
30 Amp Pink
–
VSIM #2 *
F35
30 Amp Pink
–
Sunroof *
F36
30 Amp Pink
–
Rear Defroster (EBL) *
F37
30 Amp Pink
–
Diesel Frame / Fuel HTR *
F38
30 Amp Pink
–
ITBM *
F39
–
–
Spare
F40
–
10 Amp Red
Vented Seats *
F41
–
10 Amp Red
Act Grille Shutter / Dam *
Cavity
Cartridge Fuse
Micro Fuse
Description
* If Equipped
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
401
F42
–
20 Amp Yellow
Horn
F43
–
15 Amp Blue
Heated Strng Wheel *
F44
–
10 Amp Red
Diagnostic Port
F45
–
–
Spare
F46
–
10 Amp Red
Upfitters Relay Coils *
F47
–
–
Spare
F48
–
–
Spare
F49
–
10 Amp Red
IP Cluster / CSG
F50
–
20 Amp Yellow
Air Suspension Mod *
F51
–
10 Amp Red
IGN Mod / KIN Mod/ RF Hub
F52
–
5 Amp Tan
Batt Snsr
F53
–
20 Amp Yellow
Trlr Tow – Lt Turn/Stop
F54
–
20 Amp Yellow
Non-Memory Adjustable Pedals *
F55
–
–
Spare
F56
–
10 Amp Red
Fuel Vapor Blocking Valve (VBV) *
F57
–
20 Amp Yellow
TCM / PCM / Trans PRSR SW
F58
–
10 Amp Red
Bed Lighting
F59
–
–
Spare
F60
–
–
Spare
F61
–
10 Amp Red
NH3 Sensor / PM Sensor *
Cavity
Cartridge Fuse
Micro Fuse
Description
* If Equipped
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
402
SERVICING AND MAINTENANCE
F62
–
10 Amp Red
A/C Clutch
F63
–
20 Amp Yellow
Ignition Coils / CAPS
F64
–
25 Amp Clear
Fuel Injectors
F65
–
–
Spare
F66
–
10 Amp Red
Sunroof / USB Rear * / Inside Rearview Mirror / Passenger
Window SW
F67
–
10 Amp Red
UCI Port / USB Front / Trailer Gateway Module (360 Camera) /
Tachograph
F68
–
10 Amp Red
AEB RACAM HTR *
F69
–
15 Amp Blue
SCR Mod 12 Volt *
F70
–
30 Amp Green
Fuel Pump Mtr/ Fuel Htr RLY
F71
–
25 Amp Clear
Amp / Act Noise Cnsl
F72
–
–
Spare
F73
–
20 Amp Yellow
Fuel Transfer Pump *
F74
–
10 Amp Red
Backup Alarm
F75
–
10 Amp Red
SCR RLY / ATMM*
F76
–
10 Amp Red
Electronic Stability Control (ESC) *
F77
–
10 Amp Red
DTCM / TCM / FAD MOD / STOM
F78
–
15 Amp Blue
ECM / PCM / IRCM / AUX PDC Relay Coil Feed / HRLS
F79
–
15 Amp Blue
ID / Clearance Lt
F80
–
10 Amp Red
Ovrdh Con / Assist / 911
Cavity
Cartridge Fuse
Micro Fuse
Description
* If Equipped
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
403
F81
–
20 Amp Yellow
Trlr tow Rt turn/Stop
F82
–
10 Amp Red
SCCM / Cruise control
F83
–
–
Spare
F84
–
15 Amp Blue
ASBM / HVAC / ICS / Heated Seats SW
F85
–
10 Amp Red
ORC (Airbag)
F86
–
10 Amp Red
ORC (Airbag)
F87
–
10 Amp Red
Air Susp / ITBM / SCCM / Module Gateway Trailer
F88
–
15 Amp Blue
IP Cluster
F89
–
–
Spare
F90
–
20 Amp Yellow
Power Outlet / Batt
F91
–
20 Amp Yellow
Power Outlet / Acc
F92
–
10 Amp Red
MOD Invertor (Wake Up) / Power Port / USB IP / WCPM *
F93
–
–
Spare
F94
–
10 Amp Red
SBW / TCASE SW / TRL TPM
F95
–
10 Amp Red
R CAM / PRKTRNX/ CHMSL Cam / Bld SPT SNR / SVUE CAM *
F96
–
10 Amp Red
TRL Cam *
F97
–
20 Amp Yellow
Front HTD ST PSGR *
F98
–
20 Amp Yellow
Front HTD ST DRIVER *
F99
–
10 Amp Red
HVAC / In-Car Temperature Sensor / CSG MOD / Module
Gateway Trailer / Tachograph
Cavity
Cartridge Fuse
Micro Fuse
Description
* If Equipped
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
404
SERVICING AND MAINTENANCE
BULB REPLACEMENT
Replacement Bulbs, Names, And Part Numbers
In the instance a bulb needs to be replaced, this section includes bulb description and replacement part numbers. All of the inside bulbs are brass or glass-wedge
base. Aluminum base bulbs are not approved.
NOTE:
Please see an authorized dealer for LED replacement
F100
–
10 Amp Red
Upfitter Box Feed *
F101
–
20 Amp Yellow
RR HTD ST Right *
F102
–
20 Amp Yellow
RR HTD ST Left / Run RLY #3 *
F103
–
10 Amp Red
HeadLamp AFLS *
F104
–
20 Amp Yellow
UCI Port / USB Rear
Cavity
Cartridge Fuse
Micro Fuse
Description
* If Equipped
Interior Bulbs
Bulb Name
Bulb Number
Overhead Console Lamps
TS 212–9
Dome Lamp
7679
For lighted switches, see an authorized dealer for replacement instructions.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
405
Exterior Bulbs
Bulb Name
Bulb Number
Low Beam (Halogen Reflector Headlamp)
H11LL
High Beam (Halogen Reflector Headlamp)
9005LL
Low & High Beam (LED Reflector Headlamp)
LED (Serviced at an authorized dealer)
Low & High Beam (LED Projector Headlamp)
LED (Serviced at an authorized dealer)
Turn Signal / Front Position (Halogen Reflector Headlamp)
7444NA
Turn Signal (LED Projector Headlamp)
LED (Serviced at an authorized dealer)
Front Position (LED Headlamps)
LED (Serviced at an authorized dealer)
Front Side Marker (Headlamps)
LED (Serviced at an authorized dealer)
Front Fog Lamps (Halogen Reflector Headlamp)
H11LL
Front Fog Lamps (LED Headlamps)
LED (Serviced at an authorized dealer)
Side Indicators (Front And Side View Mirror)
LED (Serviced at an authorized dealer)
Base Rear Tail/Turn and Stop Lamp
3157K
Premium Rear Tail/Turn and Stop Lamp
LED (Serviced at an authorized dealer)
Base Tail/Backup Lamp
W21/5W
Center High Mounted Stop Lamp (CHMSL)
921
Cab Roof Marker Lamps
LED (Serviced at an authorized dealer)
Rear Lamp Bar ID Marker Lamp
LED (Serviced at an authorized dealer)
Side Marker Lamps (Dual Rear Wheels)
LED (Serviced at an authorized dealer)
Base Turn/Tail Lamp
PWY24W
Rear License Plate Lamp
LED (Serviced at an authorized dealer)
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
406
SERVICING AND MAINTENANCE
Replacing Exterior Bulbs
BASE QUAD: LOW BEAM HEADLAMP, HIGH
BEAM HEADLAMP, FRONT PARK AND TURN —
IF EQUIPPED
Low Beam
See below steps to replace:
1. Open the hood.
2. Disconnect and isolate the negative battery
cable.
3. Reach into the front wheel house ahead of the
front wheel, remove the fastener, and lift the
cover over the access hole in the front of the
wheel house splash shield. Access to the rear
of the lamp can be gained through this access
hole.
Splash Shield Access Cover
4. Reach through the access hole of the wheel
house splash shield and disengage the bulb
access cover by rotating counterclockwise.
Bulb Access Cover
5. Disconnect the internal lamp wiring harness
connector from the low beam bulb.
6. Rotate the bulb counterclockwise a quarter
turn to unlock the bulb from the lamp.
7. Pull the bulb straight out from the housing.
8. Reverse the procedure for installation of new
bulb and covers.
High Beam
See below steps to replace:
1. Open the hood.
2. Disconnect and isolate the negative battery
cable.
Bulb Access Cover
3. Look under the hood and behind the
headlamp to find the high beam bulb access
cover.
CAUTION!
Do not contaminate the bulb glass by touching
it with your fingers or by allowing it to contact
other oily surfaces. Shortened bulb life will
result.
Always use the correct bulb size and type for
replacement. An incorrect bulb size or type
may overheat and cause damage to the lamp,
the bulb socket, or the lamp wiring.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
407
4. Reach behind the headlamp and disengage
the access cover by rotating counterclockwise.
5. Disconnect the internal lamp wiring harness
connector from the high beam bulb.
6. Rotate the bulb counterclockwise a quarter
turn to unlock the bulb from the lamp.
7. Pull the bulb straight out from the housing.
8. Reverse the procedure for installation of new
bulb and covers.
Outer Front Park And Turn
See below steps to replace:
1. Open the hood.
2. Disconnect and isolate the negative battery
cable.
3. Reach into the front wheel house ahead of the
front wheel, remove the fastener, and lift the
cover over the access hole in the front of the
wheel house splash shield. Access to the rear
of the lamp can be gained through this access
hole.
Splash Shield Access Cover
4. Reach through the access hole of the wheel
house splash shield and disengage the side
marker socket by rotating counterclockwise a
quarter turn.
Park And Turn Sockets
5. Pull the socket and bulb straight out from the
housing.
6. Separate the bulb from the socket without
twisting.
7. Reverse the procedure for installation of new
bulb and covers.
FOG LAMPS — IF EQUIPPED
Please see an authorized dealer for service on LED
and Halogen front fog lamps.
CAUTION!
Do not contaminate the bulb glass by touching
it with your fingers or by allowing it to contact
other oily surfaces. Shortened bulb life will
result.
Always use the correct bulb size and type for
replacement. An incorrect bulb size or type
may overheat and cause damage to the lamp,
the bulb socket, or the lamp wiring.
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
408
SERVICING AND MAINTENANCE
Halogen
See below steps to replace:
1. Reach under and behind the front fascia/
bumper to access the back of the front fog
lamp housing.
2. Disconnect the fog lamp wiring harness
connector from the fog lamp bulb.
3. Rotate the bulb counterclockwise a quarter
turn to unlock the bulb from the housing.
Fog Lamp Bulb
4. Pull the bulb straight out from the housing.
REAR TAIL/STOP, TURN SIGNAL AND BACKUP
LAMPS
See below steps to replace:
1. Remove the two screws and push pins that
pass through the bed sheet metal.
Tail Lamp Locations
2. Pull the outboard side of the lamp rearward far
enough to unsnap the two receptacles on the
outboard side of the lamp housing from the
two plastic snap post retainers in the outer box
side panel.
Tail Lamp Removed
3. Disconnect the wiring harness connectors
from the bulb socket.
4. Rotate the bulb socket counterclockwise a
quarter turn to unlock it from the housing.
5. Pull the bulb straight out of the socket.
6. Reverse the procedure to install the bulb and
housing.
CAUTION!
Do not contaminate the bulb glass by touching it
with your fingers or by allowing it to contact other
oily surfaces. Shortened bulb life will result.
1 — Tail Lamp
2 — Screws
3 — Fasteners
CAUTION!
Do not contaminate the bulb glass by touching it
with your fingers or by allowing it to contact other
oily surfaces. Shortened bulb life will result.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
409
CENTER HIGH MOUNTED STOP LAMP (CHMSL)
WITH CARGO LAMP
See below steps to replace:
1. Remove the two screws holding the housing/
lens to the body as shown.
CHMSL Mounting Screw Locations
2. Separate the connector holding the housing
and wiring harness to the body.
3. Turn the desired bulb socket a quarter turn
and remove the socket and bulb from housing.
4. Pull the desired bulb straight from the socket.
CHMSL Bulb And Socket
Outside Bulbs: Cargo Lamps
Inside Bulb: Center High Mounted Stop
Lamp
5. Reverse the procedure for installation of bulbs
and housing.
CAB TOP CLEARANCE LAMPS — IF EQUIPPED
See below steps to replace:
1. Remove the screws from the top of the lamp.
Screw Location From Clearance Lamp
2. Rotate the bulb socket a quarter turn and pull
it from the lamp assembly.
Removing Bulb Socket From Clearance Lamp
3. Pull the bulb straight from it's socket and
replace.
CAUTION!
Do not contaminate the bulb glass by touching it
with your fingers or by allowing it to contact other
oily surfaces. Shortened bulb life will result.
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
410
SERVICING AND MAINTENANCE
REAR LAMP BAR ID MARKER (DUAL REAR
WHEELS) — IF EQUIPPED
See below steps to replace:
1. Loosen the two screws and the housing to
gain access to the bulb sockets.
Screw Locations
2. Turn the socket a quarter turn counter
-
clockwise to access the bulb.
3. Pull the bulb straight out from the socket.
4. Reverse the procedure for installation of the
bulbs and housing.
SIDE MARKER LAMPS (DUAL REAR WHEELS) —
IF EQUIPPED
See below steps to replace:
Side Marker Lamp Locations
1. Push rearward on the side marker lamp
assembly.
2. Pull the entire assembly from the fender.
3. Turn the socket a quarter turn counter
-
clockwise and remove from assembly to
access the bulb.
4. Pull the bulb straight out from socket.
5. Reverse the procedure for installation of the
bulbs and housing.
TIRES
T
IRE
S
AFETY
I
NFORMATION
Tire safety information will cover aspects of the
following information: Tire Markings, Tire
Identification Numbers, Tire Terminology and
Definitions, Tire Pressures, and Tire Loading.
Tire Markings
Tire Markings
1 — US DOT Safety Standards Code (TIN)
2 — Size Designation
3 — Service Description
4 — Maximum Load
5 — Maximum Pressure
6 — Treadwear, Traction and
Temperature Grades
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
411
NOTE:
P (Passenger) — Metric tire sizing is based on US
design standards. P-Metric tires have the letter
“P” molded into the sidewall preceding the size
designation. Example: P215/65R15 95H.
European — Metric tire sizing is based on Euro
-
pean design standards. Tires designed to this
standard have the tire size molded into the side
-
wall beginning with the section width. The letter
"P" is absent from this tire size designation.
Example: 215/65R15 96H.
LT (Light Truck) — Metric tire sizing is based on
US design standards. The size designation for
LT-Metric tires is the same as for P-Metric tires
except for the letters “LT” that are molded into
the sidewall preceding the size designation.
Example: LT235/85R16.
Temporary spare tires are designed for tempo
-
rary emergency use only. Temporary high pres
-
sure compact spare tires have the letter “T” or
“S” molded into the sidewall preceding the size
designation. Example: T145/80D18 103M.
High flotation tire sizing is based on US design
standards and it begins with the tire diameter
molded into the sidewall.
Example: 31x10.5 R15 LT.
TIRE SIZING CHART
EXAMPLE:
Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT
P = Passenger car tire size based on US design standards, or
". blank. " = Passenger car tire based on European design standards, or
LT = Light truck tire based on US design standards, or
T or S = Temporary spare tire or
31 = Overall diameter in inches (in)
215, 235, 145 = Section width in millimeters (mm)
65, 85, 80 = Aspect ratio in percent (%)
Ratio of section height to section width of tire, or
10.5 = Section width in inches (in)
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст