Acura RDX (2021 year). Manual in english — page 34
543
uu
Maintenance Minder
TM
u
To Use Maintenance Minder
TM
Main
tenan
ce
Reset the maintenance minder information display if you have performed the
maintenance service.
1.
Set the power mode to ON.
2.
Press the right selector wheel until the content is displayed.
3.
Roll the right selector wheel until the
Maintenance
screen is displayed.
4.
Press and hold the right selector wheel for about 10 seconds to enter the reset mode.
5.
Roll the right selector wheel to select a maintenance item to reset, or to select
All
Due Items
(You can also press the right selector wheel to the left to end the
process).
6.
Press the right selector wheel to reset the selected item.
7.
Repeat from step 4 for other items you wish to reset.
■
Resetting the Display
1
NOTICE
Failure to reset the Maintenance Minder
TM
display
after a maintenance service results in the system
showing incorrect maintenance intervals, which can
lead to serious mechanical problems.
The dealer will reset the Maintenance Minder
TM
display after completing the required maintenance
service. If someone other than a dealer performs
maintenance service, reset the Maintenance
Minder
TM
display yourself.
You can also reset the Maintenance Minder
TM
display
using the audio/information screen.
2
P. 341
Right Selector Wheel
-------------------------------------------------------------------------------------------------------------------------------------------------------------
544
Main
tenan
ce
Maintenance Under the Hood
Maintenance Items Under the Hood
Brake Fluid
(Black Cap)
Engine Coolant
Reserve Tank
Radiator Cap
Washer Fluid
(Black Cap)
Engine Oil Dipstick
(Orange)
Engine Oil Fill Cap
Battery
-------------------------------------------------------------------------------------------------------------------------------------------------------------
545
uu
Maintenance Under the Hood
u
Opening the Hood
Main
tenan
ce
Opening the Hood
1.
Park the vehicle on a level surface, and set
the parking brake.
2.
Pull the hood release handle under the
driver’s side lower corner of the dashboard.
u
The hood will pop up slightly.
3.
Push the hood latch lever (located under
the front edge of the hood to the center) to
the side and raise the hood. Once you have
raised the hood slightly, you can release the
lever.
4.
Lift the hood up most of the way.
u
The hydraulic supports will lift it up the
rest of the way and hold it up.
When closing, lower it to approximately
12 inches (30 cm), then press down firmly with
your hands.
1
NOTICE
Do not open the hood when the wiper arms are
raised. The hood will strike the wipers, resulting in
possible damage to the hood and/or the wipers.
NOTICE
Do not press the engine cover forcibly. This may
damage the engine cover and component parts.
When closing the hood, check that the hood is
securely latched.
If the hood latch lever moves stiffly, or if you can
open the hood without lifting the lever, the latch
mechanism should be cleaned and lubricated.
Do not open the hood while the Auto Idle Stop
function is activated.
Hood Release Handle
Pull
Lever
-------------------------------------------------------------------------------------------------------------------------------------------------------------
546
uu
Maintenance Under the Hood
u
Engine Compartment Cover
Main
tenan
ce
Engine Compartment Cover
The component parts in the engine compartment are protected by a cover.
You may need to remove the cover when you perform certain maintenance work.
Pull up on the engine compartment cover carefully until all pins are removed from
their grommets.
Remove the Engine Compartment Cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
547
uu
Maintenance Under the Hood
u
Recommended Engine Oil
Main
tenan
ce
Recommended Engine Oil
Use a genuine engine oil or another commercial engine oil of suitable type and
viscosity (for the ambient temperature) as shown in the image that follows.
Oil is a major contributor to your engine’s performance and longevity. If you drive
the vehicle with insufficient or deteriorated oil, the engine may fail or be damaged.
*1:Formulated to improve fuel economy.
■
Synthetic oil
You may also use synthetic motor oil if it is labeled with the API Certification Seal
and is the specified viscosity grade.
Genuine Engine Oil
Commercial Engine Oil
●
Acura Genuine Motor Oil
●
Premium-grade 0W-20 detergent oil
with an API Certification Seal on the
container.
1
Engine Oil Additives
Your vehicle does not require oil additives. In fact,
they may adversely affect the engine performance
and durability.
The following seal indicates the oil is energy
conserving and that it meets the American Petroleum
Institute’s latest requirements.
Ambient Temperature
Ambient Temperature
-------------------------------------------------------------------------------------------------------------------------------------------------------------
548
uu
Maintenance Under the Hood
u
Oil Check
Main
tenan
ce
Oil Check
We recommend that you check the engine oil level every time you refuel.
Park the vehicle on level ground.
Wait approximately three minutes after turning the engine off before you check the
oil.
1.
Remove the dipstick (orange).
2.
Wipe the dipstick with a clean cloth or
paper towel.
3.
Insert the dipstick back all the way into its
hole.
4.
Remove the dipstick again, and check the
level. It should be between the upper and
lower marks. Add oil if necessary.
1
If the oil level is near or below the lower mark, slowly
add oil, being careful not to overfill.
Lower Mark
Upper Mark
-------------------------------------------------------------------------------------------------------------------------------------------------------------
549
uu
Maintenance Under the Hood
u
Adding Engine Oil
Main
tenan
ce
Adding Engine Oil
1.
Unscrew and remove the engine oil fill cap.
2.
Add oil slowly.
3.
Reinstall the engine oil fill cap, and tighten
it securely.
4.
Wait for three minutes and recheck the
engine oil dipstick.
1
NOTICE
Do not fill the engine oil above the upper mark.
Overfilling the engine oil may result in leaks and
engine damage.
If any oil spills, wipe it away immediately. Spilled oil
may damage the engine compartment components.
Engine Oil
Fill Cap
-------------------------------------------------------------------------------------------------------------------------------------------------------------
550
uu
Maintenance Under the Hood
u
Changing the Engine Oil and Oil Filter
Main
tenan
ce
Changing the Engine Oil and Oil Filter
You must change the engine oil and oil filter regularly in order to maintain the
engine’s lubrication. The engine may be damaged if they are not changed regularly.
Change the oil and filter in accordance with the maintenance message on the multi-
information display.
1.
Run the engine until it reaches normal
operating temperature, and then turn the
engine off.
2.
Open the hood and remove the engine oil
fill cap.
3.
Remove the slotted head screws by
turning 90° counterclockwise on the
undercarriage and remove the under
cover.
4.
Remove the drain bolt and washer from
the bottom of the engine, and drain the
oil into a suitable container.
1
Changing the Engine Oil and Oil Filter
NOTICE
You may damage the environment if you do not
dispose of the oil in a suitable way. If you are
changing the oil by yourself, appropriately dispose of
the used oil. Put the oil in a sealed container and take
it to a recycling center. Do not throw the oil away
into a garbage can or onto the ground.
Screw
Under Cover
Drain Bolt
Washer
-------------------------------------------------------------------------------------------------------------------------------------------------------------
551
uu
Maintenance Under the Hood
u
Changing the Engine Oil and Oil Filter
Main
tenan
ce
5.
Remove the oil filter and dispose of the
remaining oil.
6.
Check that the filter gasket is not stuck to
the engine contact surface.
u
If it is stuck, you must detach it.
7.
Wipe away dirt and dust adhering to the
contact surface of the engine block, and
install a new oil filter.
u
Apply a light coat of new engine oil to
the filter gasket.
8.
Put a new washer on the drain bolt, then
reinstall the drain bolt.
u
Tightening torque:
29 lbf∙ft (40 N∙m, 4.0 kgf∙m)
9.
Pour the recommended engine oil into the
engine.
u
Engine oil change capacity (including
filter):
5.0 US qt (4.8 L)
10.
Reinstall the engine oil fill cap securely and
start the engine.
11.
Run the engine for a few minutes, and
then check that there is no leak from the
drain bolt or oil filter.
12.
Stop the engine, wait for three minutes,
and then check the oil level on the
dipstick.
u
If necessary, add more engine oil.
1
Changing the Engine Oil and Oil Filter
You will need a special wrench to replace the oil
filter. You can buy this wrench from a dealer.
When installing the new oil filter, follow the
instructions supplied with the oil filter.
Reinstall the engine oil fill cap. Start the engine. The
low oil pressure indicator should go off within five
seconds. If it does not, turn off the engine, and check
your work.
Oil Filter
-------------------------------------------------------------------------------------------------------------------------------------------------------------
552
uu
Maintenance Under the Hood
u
Engine Coolant
Main
tenan
ce
Engine Coolant
This coolant is premixed with 50% antifreeze and 50% water. Do not add any
straight antifreeze or water.
We recommend you check the engine coolant level every time you refuel. Check the
reserve tank first. If it is completely empty, also check the coolant level in the
radiator. Add the engine coolant accordingly.
1. Make sure the engine and radiator are
cool.
2.
Check the amount of coolant in the reserve
tank.
u
If the coolant level is below the
MIN
mark, add the specified coolant until it
reaches the
MAX
mark.
3.
Inspect the cooling system for leaks.
Specified coolant: Acura Long Life Antifreeze/Coolant Type 2
■
Reserve Tank
1
NOTICE
Genuine Acura engine coolant is a 50/50 mixture of
antifreeze and water that can withstand freezing at
temperatures as low as about -31°F (-35°C). If your
vehicle is consistently subjected to temperatures
below this, the concentration of antifreeze in the
coolant should be increased. Consult a dealer for
details.
If Acura antifreeze/coolant is not available, you may
use another major brand of non-silicate coolant as a
temporary replacement. Check that it is a high quality
coolant recommended for aluminum engines.
Continued use of any non-Acura coolant can result in
corrosion, causing the cooling system to malfunction
or fail. Have the cooling system flushed and refilled
with Acura antifreeze/coolant as soon as possible.
Do not add rust inhibitors or other additives to your
vehicle’s cooling system. They may not be compatible
with the coolant or with the engine components.
Reserve Tank
MAX
MIN
-------------------------------------------------------------------------------------------------------------------------------------------------------------
553
uu
Maintenance Under the Hood
u
Engine Coolant
Main
tenan
ce
1. Make sure the engine and radiator are
cool.
2.
Remove the engine compartment cover.
2
P. 546
3.
Turn the radiator cap 1/8 turn
counterclockwise and relieve any pressure
in the cooling system.
4.
Push down and turn the radiator cap
counterclockwise to remove it.
5.
The coolant level should be up to the base
of the filler neck. Add coolant if it is low.
6.
Put the radiator cap back on, and tighten it
fully.
■
Radiator
1
NOTICE
Pour the fluid slowly and carefully so you do not spill
any. Clean up any spills immediately; they can
damage components in the engine compartment.
3
WARNING
Removing the radiator cap while the
engine is hot can cause the coolant to spray
out, seriously scalding you.
Always let the engine and radiator cool
down before removing the radiator cap.
Radiator Cap
-------------------------------------------------------------------------------------------------------------------------------------------------------------
554
uu
Maintenance Under the Hood
u
Transmission Fluid
Main
tenan
ce
Transmission Fluid
Have a dealer check the fluid level and replace if necessary.
Do not attempt to check or change the automatic transmission fluid yourself.
■
Automatic Transmission Fluid
Specified fluid: Acura ATF-type 2.0
1
NOTICE
Do not mix Acura ATF-type 2.0 with other
transmission fluids.
Using a transmission fluid other than Acura ATF-type
2.0 may adversely affect the operation and durability
of your vehicle’s transmission, and damage the
transmission.
Any damage caused by using a transmission fluid that
is not equivalent to Acura ATF-type 2.0 is not covered
by Acura’s new vehicle limited warranty.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
555
uu
Maintenance Under the Hood
u
Brake Fluid
Main
tenan
ce
Brake Fluid
The fluid level should be between the
MIN
and
MAX
marks on the side of the reserve
tank.
Specified fluid: Acura Heavy Duty Brake Fluid DOT 3
■
Checking the Brake Fluid
1
NOTICE
Brake fluid marked DOT 5 is not compatible with your
vehicle’s braking system and can cause extensive
damage.
If the specified brake fluid is not available, you should
use only DOT 3 or DOT 4 fluid from a sealed
container as a temporary replacement.
Using any non-Acura brake fluid can cause corrosion
and decrease the longevity of the system. Have the
brake system flushed and refilled with Acura Heavy
Duty Brake Fluid DOT 3 as soon as possible.
If the brake fluid level is at or below the
MIN
mark,
have a dealer inspect the vehicle for leaks or worn
brake pads as soon as possible.
Brake Reserve Tank
MIN
MAX
-------------------------------------------------------------------------------------------------------------------------------------------------------------
556
uu
Maintenance Under the Hood
u
Refilling Window Washer Fluid
Main
tenan
ce
Refilling Window Washer Fluid
Open the cap and check the amount of window washer fluid.
If the level is low, fill the washer reservoir.
If the washer fluid is low, a message appears
on the multi-information display.
Pour the washer fluid carefully. Do not overflow the reservoir.
1
NOTICE
Do not use engine antifreeze or a vinegar/water
solution in the windshield washer reservoir.
Antifreeze can damage your vehicle’s paint. A
vinegar/water solution can damage the windshield
washer pump.
Use only commercially available windshield washer
fluid.
Avoid prolonged use of hard water to prevent lime
scale build up.
Cap
Canadian models
-------------------------------------------------------------------------------------------------------------------------------------------------------------
557
Main
tenan
ce
Replacing Light Bulbs
Headlights
Headlights are LED type. Have an authorized Acura dealer inspect and replace the
light assembly.
Front Turn Signal, Parking/Daytime Running and
Front Side Marker Lights
Front turn signal, parking/daytime running and front side marker lights are LED type.
Have an authorized Acura dealer inspect and replace the light assembly.
Fog Lights
*
Fog lights are LED type. Have an authorized Acura dealer inspect and replace the
light assembly.
Side Turn Signal/Emergency Indicator Lights
Door mirror side turn lights are LED type. Have an authorized Acura dealer inspect
and replace the light assembly.
1
The headlight aim is set by the factory, and does not
need to be adjusted. However, if you regularly carry
heavy items in the cargo area or tow a trailer, have
the aiming readjusted at a dealer or by a qualified
technician.
* Not available on all models
-------------------------------------------------------------------------------------------------------------------------------------------------------------
558
uu
Replacing Light Bulbs
u
Rear Turn Signal Light Bulbs
Main
tenan
ce
Rear Turn Signal Light Bulbs
When replacing, use the following bulbs.
1.
Remove the cover by prying on the edge
using a flat-tip screwdriver.
u
Wrap the flat-tip screwdriver with a cloth
to prevent scratches.
2.
Use a Phillips-head screwdriver to remove
the bolts.
3.
Pull the light assembly out of the rear pillar.
Rear Turn Signal Light: 21 W (PY21W Amber/Silver)
Cover
Bolts
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст