Acura RL (1996-2004 year). Manual — part 348
20. Align the maintenance hole and the balancer shaft
hole. Insert a 6 mm bolt that is at least 45 mm (1.8
in) long into the balancer shaft.
45 mm (1.8 in) or longer
6 mm BOLT
BALANCER
SHAFT
12 mm SEALING BOLT
20 N-m (2.0 kgf-m, 14 Ibf-ft)
WASHER
Replace.
21. Apply liquid gasket to the oil pump mating surface
of the balancer gear case.
BALANCER GEAR
CASE
O-RING
GROOVE
Apply liquid gasket
along the broken line.
24. Remove the 6 mm bolt. Install the sealing bolt in the
maintenance hole. Use a new washer.
22. Install the balancer gear case.
6 x 1.0 mm
12 N-m (1.2 kgf-m,
8.7 Ibf-ft)
BALANCER
GEAR CASE
DOWEL
PIN
O-RING
Replace.
23. Check alignment of the pointers after installing the
balancer gear case.
BALANCER BELT
DRIVEN PULLEY
POINTER
BALANCER GEAR
CASE POINTER
Main Menu
Table of Contents
Crankshaft Oil Seals
Installation (engine removal not required)
NOTE: The seal surface on the block should be dry.
Apply a light coat of grease to the crankshaft and to the
lips of the seals.
1. Using the special tools, drive in the crankshaft oil
seal until the driver bottoms against the oil pump.
When the seal is in place, clean any excess grease
off the crankshaft and check that the oil seal lip is
not distorted.
Install seal with the
part number side
facing out.
Tape tools
together.
SEAL DRIVER
SUPPORT COLLAR
2. Measure the crankshaft oil seal thickness and the oil
seal housing depth. Using the special tool, drive the
crankshaft oil seal into the rear cover to the point
where the clearance between the bottom of the oil
seal and the rear cover is 0.2 - 0.5 mm (0.01 - 0.02
).
NOTE: Align the hole in the driver attachment with
the pin on the crankshaft.
DRIVER
DRIVER ATTACHMENT
Install seal with the
part number side
facing out.
Main Menu
Table of Contents
Special Tools
07LAC-PW50101
07MAF-PY40101
07746-0010500
07749-0010000
07912-6110001
Tool Number
Main Menu
Table of Contents
Illustrated Index
NOTE:
• Use new O-rings when reassembling.
• Apply oil to O-rings before installation.
• Use liquid gasket, Part No. 08718 - 0001 or 08718 - 0003.
• Clean the oil control orifice before installing.
• Remove the balancer shaft (see page
).
OIL CONTROL ORIFICE
(HYDRAULIC TAPPET)
Remove with 6 x 1.0 mm bolt
and clean.
OIL CONTROL ORIFICES
(CAMSHAFT JOURNAL)
Remove with 6 x 1.0 mm
bolt and clean.
Apply liquid gasket to
block mating surface.
O-RING
Replace.
6 x 1.0 mm
12 N-m (1.2 kgf-m,
8.7 Ibf-ft)
8 x 1.25 mm
22 N-m (2.2 kgf-m,
16 Ibf-ft)
OIL CONTROL ORIFICE
(HYDRAULIC TAPPET)
Remove with 6 x 1.0 mm bolt
and clean.
O-RINGS
Replace.
6 x 1.0 mm
12 N-m (1.2 kgf-m,
8.7 Ibf-ft)
BAFFLE PLATE
6 x 1.0 mm
12 N-m (1.2 kgf-m,
8.7 Ibf-ft)
SNAP RING
Install with open
side facing up.
6 x 1.0 mm
12 N-m (1.2 kgf-m, 8.7 Ibf-ft)
LOWER BAFFLE
PLATE
DOWEL PIN
OIL PAN
Apply liquid gasket
to mating surface.
8 x 1.25 mm
22 N-m (2.2 kgf-m,
16 Ibf-ft)
O-RINGS
Replace.
OIL FILTER
DRAIN BOLT
14 x 1.5 mm
44 N-m (4.5 kgf-m, 33 Ibf-ft)
Do not overtighten.
OIL PAN INNER
PIPE
Clean before installing.
O-RING
Replace.
O-RINGS
Replace.
O-RING
Replace.
OIL SCREEN
O-RING
Replace.
WASHER
Replace.
Main Menu
Table of Contents
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст