Acura RL (1996-2004 year). Manual — part 647
Multiplex Control System
Self-diagnosis Function (Mode 2)
From mode 1, disconnect the SCS service connector from the multiplex control inspection connector for 5 to 10
seconds, then reconnect the SCS service connector again, and the function goes from mode 1 to mode 2.
To cancel mode 2, disconnect the SCS service connector from the multiplex control inspection connector for more than 10
seconds or turn the ignition switch OFF.
1. Operate the switches as shown below in mode 2.
2. If the related circuit line of the switch is OK, the function indicates this by the ignition key light blinking once and the
beeper sounding once.
NOTE: If the line is faulty, there should be no indication. Refer to the tests for each system.
Object Input Table:
Mode 2:
Hood switch (OPEN)
Trunk latch switch (OPEN)
Radio security input
Trunk opener main switch
Front passenger's door switch
(OPEN)
Front passenger's key cylinder switch
(LOCK/UNLOCK)
Front passenger's door lock switch
(LOCK/UNLOCK)
Front passenger's door lock knob
switch (UNLOCK)
Right rear door switch (OPEN)
Right rear door lock knob switch
(UNLOCK)
Keyless transmitter
(LOCK button)
(UNLOCK button)
(TRUNK button)
(PANIC button)
Rear window defogger switch
Engine oil pressure switch
Multiplex Control Unit (Passenger's)
Multiplex Control Unit (Driver's)
Combination light switch (ON)
Front fog light switch (ON)
Dash lights brightness controller
Left rear door switch (OPEN)
Left rear door lock knob switch
(UNLOCK)
Trunk key cylinder switch (OPEN)
Driver's seat belt switch
(UNBUCKLED)
Windshield wiper/washer switch
(Except MIST switch)
Brake switch (ON)
Vehicle speed sensor (VSS)
Parking brake switch (ON)
Transmission range switch
Multiplex Control Unit (Door)
Driver's door switch (OPEN)
Driver's door key cylinder switch
(LOCK/UNLOCK)
Driver's door lock switch
(LOCK/UNLOCK)
Driver's door lock knob switch
(LOCK/UNLOCK)
Trunk opener switch (PUSH)
Power window master switch
(Except driver's switch)
Main Menu
Table of Contents
Integrated Control
Ignition Key Light Replacement
1. Remove the dashboard lower cover (see
).
2. Remove the column covers (see
).
3. Turn the bulb socket 45° counterclockwise to remove
it from the key light housing.
BULB (1.4 W)
KEY LIGHT
HOUSING
BULB
SOCKET
Main Menu
Table of Contents
Dash Lights Brightness Control
Controller Test/Replacement
1. Remove the driver's switch panel (see
).
2. Measure resistance between the No. 3 and No. 4 ter-
minals while rotating the adjusting dial. Resistance
should vary from 0 to 10,000 ohms as the dial is
rotated.
DRIVER'S SWITCH
PANEL
BULB
(0.84 W)
DASH LIGHTS
BRIGHTNESS
CONTROLLER
3. Turn the CANCEL switch off by rotating the adjusting
beyond its end position (until if clicks). There should
be no continuity between the No. 2 and No. 6 termi-
nals.
NOTE: The cancel switch is closed with the adjusting
dial between the minimum and maximum positions.
4. If necessary, remove the two screws, and replace the
controller.
SCREWS
Main Menu
Table of Contents
LEFT REAR DOOR SWITCH*
Test, page
LEFT REAR DOOR
COURTESY LIGHT
Replacement,
page
DRIVER'S DOOR
COURTESY LIGHT
Replacement,
page
DRIVER'S DOOR SWITCH*
Test, page
FRONT PASSENGER'S DOOR
COURTESY LIGHT
Replacement, page
FRONT PASSENGER'S*
DOOR SWITCH
Test, page
RIGHT REAR DOOR SWITCH*
Test, page
RIGHT REAR DOOR
COURTESY LIGHT
Entry Light Control System
Component Location Index
• IGNITION KEY SWITCH
*: You can also test the switch by using the self-diagnosis function (mode 2). (See page
.)
Main Menu
Table of Contents
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст