Acura RL (1996-2004 year). Manual — part 705
DTC 4-3
CAUTION: Whenever the ignition switch is ON (II), or
has been turned OFF for less than 3 minutes, be careful
not to bump the SRS unit or the side impact sensor; the
airbags could accidentally deploy and cause damage or
injuries.
Try to reproduce the SRS indicator light:
1. Erase the DTC memory (see page
).
2. Turn the ignition switch ON (II), and check that the SRS
indicator light comes on for about 6 seconds, and then
goes off.
Check for a short to another wire in the SRS floor harness:
1. Disconnect the negative battery cable, and wait for 3
minutes.
2. Disconnect the driver's and front passenger's side airbag
connectors, then disconnect the driver's airbag connec-
tor (see page
).
3. Disconnect the SRS floor harness 18P connector from
).
4. Disconnect the special tool from the SRS floor har-
).
5. Check resistance between the No. 6 and No. 17 terminals
of the SRS floor harness 18P connector. There should be
1 or more.
Intermittent failure, system is OK at this time. See
Troubleshooting Intermittent Failures on page
Check for a short to another wire in the front passenger's
seat belt tensioner:
1. Disconnect the negative battery cable, and wait for 3
minutes.
2. Disconnect the right side wire harness 2P connector from
the front passenger's seat belt tensioner 2P connector (see
).
3. Connect the special tool to the right side wire har-
).
4. Reconnect the negative battery cable.
5. Erase the DTC memory (see page
).
).
Short to another wire in the front passenger's seat belt
tensioner; replace the front passenger's seat belt (see
page
).
Check for a short to another wire in the right side wire har-
ness:
1. Disconnect the negative battery cable, and wait for 3
minutes.
2. Disconnect the SRS floor harness 2P connector from the
right side wire harness 2P connector (see page
).
3. Connect the special tool (2 0) to the SRS floor harness 2P
connector (see page
).
4. Reconnect the negative battery cable.
5. Erase the DTC memory (see page
).
).
Faulty SRS unit; replace the SRS unit (see page
).
Main Menu
Table of Contents
DTC 4-4
CAUTION: Whenever the ignition switch is ON (II), or
has been turned OFF for less than 3 minutes, be careful
not to bump the SRS unit or the side impact sensor; the
airbags could accidentally deploy and cause damage or
injuries.
Troubleshooting - '99 - 01 Models
Check for a short to power in the SRS floor harness:
1. Disconnect the negative battery cable, and wait for 3
minutes.
2. Disconnect the driver's and front passenger's side airbag
connectors, then disconnect the driver's airbag connec-
tor (see page
).
3. Disconnect the SRS floor harness 18P connector from
the SRS unit (see page
).
4. Check resistance between the No. 6 and No. 7 terminals
of the SRS floor harness 18P connector, and between the
No. 6 and No. 8 terminals of the SRS floor harness 18P
connector. There should be 1 or more.
Try to reproduce the SRS indicator light:
1. Erase the DTC memory (see page
).
2. Turn the ignition switch ON (II), and check that the SRS
indicator light comes on for about 6 seconds, and then
goes off.
Intermittent failure, system is OK at this time. See
Troubleshooting Intermittent Failures on page
Check for a short to power in the front passenger's seat belt
tenstoner:
1. Disconnect the negative battery cable, and wait for 3
minutes.
2. Disconnect the right side wire harness 2P connector from
the front passenger's seat belt tensioner 2P connector (see
).
3. Connect the special tool to the right side wire har-
).
4. Reconnect the negative battery cable.
5. Erase the DTC memory (see page
).
).
Short to power in the front passenger's seat belt ten-
sioner; replace the front passenger's seat belt (see page
).
Check for a short to power in the right side wire harness:
1. Disconnect the negative battery cable, and wait for 3
minutes.
2. Disconnect the SRS floor harness 2P connector from the
right side wire harness 2P connector (see page
).
3. Connect the special tool to the SRS floor harness 2P
connector (see page
).
4. Reconnect the negative battery cable.
5. Erase the DTC memory (see page
).
).
Faulty SRS unit; replace the SRS unit (see page
).
Main Menu
Table of Contents
DTC 4-5
CAUTION: Whenever the ignition switch is ON (II), or
has been turned OFF for less than 3 minutes, be careful
not to bump the SRS unit or the side impact sensor; the
airbags could accidentally deploy and cause damage or
injuries.
Check for a short to ground in the SRS floor harness:
1. Disconnect the negative battery cable, and wait for 3
minutes.
2. Disconnect the driver's and front passenger's side airbag
connectors, then disconnect the driver's airbag connec-
tor (see page
).
3. Disconnect the SRS floor harness 18P connector from
). Do not disconnect the spe-
cial tool from the SRS floor harness 2P connector
(see page
).
4. Check resistance between the No. 6 terminal of the SRS
floor harness 18P connector and body ground, and
between the No. 6 and No. 12 terminals of the SRS floor
harness 18P connector, and between the No. 6 and No.
11 terminals of the SRS floor harness 18P connector.
There should be 1 or more.
Try to reproduce the SRS indicator light:
1. Erase the DTC memory (see page
).
2. Turn the ignition switch ON (II), and check that the SRS
indicator light comes on for about 6 seconds, and then
goes off.
Intermittent failure, system is OK at this time. See
Troubleshooting Intermittent Failures on page
Check for a short to ground in the front passenger's seat
belt tensioner:
1. Disconnect the negative battery cable, and wait for 3
minutes.
2. Disconnect the right side wire harness 2P connector from
the front passenger's seat belt tensioner 2P connector (see
page
).
3. Connect the special tool to the right side wire har-
).
4. Reconnect the negative battery cable.
5. Erase the DTC memory (see page
).
).
Short to ground in the front passenger's seat belt ten-
sioner; replace the front passenger's seat belt (see page
).
Check for a short to ground in the right side wire harness:
1. Disconnect the negative battery cable, and wait for 3
minutes.
2. Disconnect the SRS floor harness 2P connector from the
right side wire harness 2P connector (see page
.
3. Connect the special tool to the SRS floor harness 2P
).
4. Reconnect the negative battery cable.
5. Erase the DTC memory (see page
).
).
Faulty SRS unit; replace the SRS unit (see page
).
Main Menu
Table of Contents
(B)
Short to ground in the No. 13 (7.5 A) fuse related circuit; refer
to
and continue troubleshooting.
Check the No. 13 (7.5 A) fuse in the under-dash fuse/relay box
(see page
):
Check for a DTC:
1. Disconnect the driver's seat belt buckle switch.
2. Erase the DTC memory (see page
).
).
Check for a DTC:
1. Connect the driver's seat belt buckle switch.
2. Erase the DTC memory (see page
).
).
Check for a short to ground between the No. 13 (7.5 A) fuse in
the under-dash fuse/relay box and the left side wire harness:
1. Disconnect the driver's tension reducer solenoid connector.
2. Erase the DTC memory (see page
).
).
Intermittent failure, system is OK at this time. See
Troubleshooting Intermittent Failures on page
Check for a DTC:
1. Disconnect the driver's seat belt buckle switch.
2. Erase the DTC memory (see page
).
).
DTC 9-3
CAUTION: Whenever the ignition switch is ON (II), or
has been turned OFF for less than 3 minutes, be careful
not to bump the SRS unit or the side impact sensor; the
airbags could accidentally deploy and cause damage or
injuries.
Troubleshooting - '99 - 01 Models
Main Menu
Table of Contents
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст