Acura RL (1996-2004 year). Manual — part 244
OnStar System ('02 Model USA)
Description (cont'd)
Stolen vehicle tracking:
If the vehicle is stolen, the owner can report it to the call center. They will notify the authorities and track the vehicle loca-
tion to assist in recovery.
Virtual advisor:
1. Virtual advisor setup. A subscriber sets up a personal profile on their home computer through the internet at the
OnStar web site.
— Stock portfolio
— Traffic
— Sports
— News
— Weather
— E-mail
2. Subscriber calls OnStar call center.
3. OnStar receives and processes request.
4. Profile accessed for requested information.
5. OnStar sends information back to subscriber. A computer voice relays the requested information.
Cellular phone:
The user can make a hands-free cellular phone call with one touch (by pressing the "dot" button), and by using voice
recognition commands.
Remote operation:
Vehicle doors can be locked remotely if forgotten or unlocked when keys are accidentally left inside the vehicle. If the vehi-
cle is misplaced in a parking lot, vehicle alert (honks the horn and Flashes the parking lights) can be requested remotely.
NOTE: During normal vehicle operation, the system is in high power mode. After the ignition switch is turned OFF the sys-
tem will go into low power mode for 48 hours, after that the system will switch to sleep mode to conserve battery power.
When in low power mode, the system will switch back to the high power mode for 1 minute out of every 10 minutes for a
period of 48 hours. Remote operation is only available during the 1 minute period of high power operation. When the sys-
tem is in sleep mode, remote operation is not possible.
Registering replacement components:
If the OnStar control unit or the OnStar radio frequency modulator unit are replaced, you must call OnStar dealer support
by regular telephone and register the new serial number(s).
OnStar control unit:
OnStar system radio
frequency modulator unit:
SERIAL NUMBER
SERIAL NUMBER
Main Menu
Table of Contents
Emergency call operation:
Button/Item
Emergency button
OnStar button
Dot button
Speaker
Phone line
LED indicator
Audio volume
Pre-call status
Button is pushed
Waiting
Green light
Call in progress
Emergency call in progress
This button is inactive during an emergency call
Ends emergency call when pushed
Sound of system calling
Connecting to call cen-
ter
Call center communication
Linking to
call center
Flashing green light
Call ends
(Dot button
pushed)
Post-call status
Waiting
Green light
Can be adjusted at any time by turning the volume knob
OnStar Call operation:
Button/Item
Emergency button
OnStar button
Dot button
Speaker
Phone line
LED indicator
Audio volume
Pre-call status
Button is pushed
Waiting
Green light
Call in progress
Will switch over to an emergency call when pushed
OnStar service call in the progress
Ends OnStar service call when pushed
Sound of system calling
Connecting to call
center
Call center communication
Linking to
call center
Call ends
(Dot button
pushed)
Flashing green light
Post-call status
Waiting
Green light
Can be adjusted at any time by turning the volume knob
Voice recognition operation:
Button/Item
Emergency button
OnStar button
Dot button
Speaker
Phone line
LED indicator
Audio volume
Pre-call status
Button is pushed
Waiting
Green light
Voice recognition mode in use
Will switch over to an emergency call when pushed
Will switch over to OnStar service call when pushed
Voice recognition mode is activated ends the voice
recognition mode when pushed a second time
"Ready"
Acknowledgement
Waiting
Feedback sound of voice recog-
nition
for verbal command
Green light
Post-call status
Waiting
Green light
Can be adjusted at any time by turning the volume knob
Voice recognition for cellular phone:
Button/Item
Emergency button
OnStar button
Dot button
Speaker
Phone line
LED indicator
Audio volume
Pre-call status
Button is pushed
Waiting
Green light
Voice recognition mode for cellular phone in use
Will switch over to an emergency call when pushed
Will switch over to OnStar service call when pushed
Voice recognition mode is activated ends the voice
recognition mode when pushed a second time
"Ready"
Acknowled-
gement
Feedback
sound of voice
recognition
Waiting for verbal command
Green light
Conversation in
progress
Linking to phone network
Flashing green light
Post-call status
Waiting
Green light
Can be adjusted at any time by turning the volume knob
Main Menu
Table of Contents
OnStar System ('02 Model USA)
Troubleshooting
1. Check the No. 56 (7.5 A) fuse in the under-hood
fuse/relay box and the No. 4 (10 A) fuse in the
under-dash fuse/relay box.
Are the fuses OK?
YES- Go to step 2.
NO- Find and repair the cause of the blown fuse.
2. Remove the rear seat (Refer to the '96-'01 3.5RL
Service Manual, P/N 61SZ305, for the items not
shown in this section).
3. Check for continuity between the A32 terminal of
the OnStar control unit and body ground.
Is there continuity?
YES- Go to step 4.
NO- Repair open in the BLK wire between the
OnStar control unit and G601.
4. Check for continuity between the B1 terminal of the
OnStar system interface unit and body ground.
Is there continuity?
YES- Go to step 5.
NO- Repair open in the BLK wire between the
OnStar system interface unit and G401, G402.
5. With the ignition switch OFF, press and hold the
"dot" button. Turn the ignition switch from OFF to
ACC three times and back to ACC, then release the
"dot" button.
6. The indicator will flash (green or red) if any failures
have been detected. Troubleshoot the DTCs as indi-
cated below:
DTC
1
2
3
4
5
Self Diagnostics Items
GPS signal error
Inter-device dedicated
bus malfunction
Deployment com-
manded circuit
malfunction
OnStar control unit
malfunction
Cellular phone select
service switch malfunc-
tion (button module)
Note
OnStar system
radio frequency
modulator unit com-
munications error
SRS signal out is
open
Will only shows as
"history" during
DTC display
Example: When DTC1 and DTC2 are detected
T1: 1 sec. T2: 0.2 sec. T3: 0.3 sec. T4: 2 sec. T5: 3 sec.
NOTE:
• Green indicator flashes historic (stored) failure DTCs.
• Red indicator flashes current failure DTCs.
• Current DTCs, are displayed first, followed by history
DTCs, if any.
• DTCs are displayed in numerical order for two cycles.
The indicator returns to normal function after the two
cycles.
How to clear the codes:
Press the OnStar button within 3 seconds after the sec-
ond DTC cycle.
How to enter demonstration mode:
1. When ignition switch is turned OFF within 3 sec
after DTC, system will be shifted to demonstration
mode.
2. Each signals will be appear in order below.
• 2 sec after ignition switch is OFF: Door lock
• 1 sec after door lock: door: Door unlock
• 1 sec after door unlock: Horn and exterior lights
period of 0.7 sec.
Main Menu
Table of Contents
OnStar Control Unit Input Test
1. Remove the rear seat (Refer to the '96 - '01 3.5RL Service Manual, P/N 61SZ305, for the items not shown in this sec-
tion).
2. Disconnect the 32P connectors from the OnStar control unit.
3. Inspect the connector and socket terminals to be sure they are all making good contact.
• If the terminals are bent, loose or corroded, repair them as necessary, and recheck the system.
• If the terminals look OK, make the following input tests at the connector.
— If any test indicates a problem, find and correct the cause, then recheck the system.
— If all the input tests prove OK, the control unit must be faulty; replace it.
32P CONNECTOR A (red):
Wire side of female
terminals
32P CONNECTOR B (blue):
Wire side of female terminals
Main Menu
Table of Contents
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст