Acura RL (1996-2004 year). Manual — part 576
Seats
Component Location Index
SRS components are located in this areas marked with an asterisk (*). Review the SRS component locations, precautions,
and procedures in the Restraints (
) before performing repairs or service.
*FRONT SEATS
Seat Linkage Disassembly, page
Seat Wire Harness Installation, page
Trunk pass-through cover
Key Cylinder Replacement, page
Main Menu
Table of Contents
Front Seat
Removal
SRS components are located in this area. Review the
SRS component locations, precautions, and procedures
in the Restraints (
) before performing repairs
or service.
CAUTION: When prying with a flat-tip screwdriver, wrap
it with protective tape to prevent damage.
NOTE: Take care not to scratch the seat covers and body.
1. Make sure you have the anti-theft code for the
radio, then write down the frequencies for the pre-
set buttons.
2. Disconnect the negative battery cable, and wait at
least 3 minutes before beginning work.
3. Remove the seat track end covers, then remove the
bolts.
Seat track end cover removal:
Bolt locations, 4
10 x 1.25 mm
37 N-m (3.8 kgf-m,
27 Ibf-ft)
SEAT TRACK
END COVER
SEAT TRACK
END COVER
SEAT TRACK
END COVERS
FRONT SEAT
4. Lift the front seat, then disconnect the connectors.
Driver's seat:
SIDE AIRBAG
CONNECTOR
('99 - 01 models)
SEAT HEATER
CONNECTOR
(for some
models)
SEAT BELT
SWITCH
CONNECTOR
Passenger's seat:
SIDE AIRBAG
CONNECTOR
('99 - 01 models)
Clip location
POWER
SEAT
CONNECTOR
SEAT BELT
SWITCH
CONNECTOR
POWER SEAT
CONNECTOR
5. Remove the headrest.
6. Carefully remove the front seat through the door
opening.
7. Installation is the reverse of the removal procedure.
NOTE:
Make sure the connectors are connected properly.
Enter the anti-theft code for the radio, then enter
the customer's radio station presets.
SEAT HEATER
CONNECTOR
(for some
models)
OPDS UNIT
CONNECTOR
('99 - 01 models
Main Menu
Table of Contents
Front Seat
Disassembly
CAUTION: When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage.
NOTE: Take care not to scratch the seat covers and body.
HEADREST
8-way power adjustable (with seat heater):
for the seat wire harness installation.
BACK COVER
SEAT-BACK
PIVOT NUT
8 x 1.25 mm
22 N-m (2.2 kgf-m,
16 Ibf-ft)
SEAT CUSHION
CLIP
To seat cushion
cover.
CENTER
COVER
10 x 1.25 mm
47 N-m (4.8 kgf-m,
35 Ibf-ft)
CLIP
To seat cushion
cover.
SEAT LINKAGE
Disassembly, page
Installation is the reverse of the removal procedure.
KNOBS
CAP
NOTE:
Make sure the bushing and pivot washer are installed properly.
To prevent wrinkles when installing the seat-back cover, make sure the material is stretched evenly over the pad.
Grease the sliding portion.
POWER SEAT
SWITCH
RECLINE
COVER
RECLINE ADJUSTER
COVER
10 x 1.25 mm
47 N-m (4.8 kgf-m, 35 Ibf-ft)
BUSHING
SEAT HEATER
CONNECTOR
SIDE AIRBAG
CONNECTOR
('99 - 01 models)
HOOK
CLIPS
SEAT-BACK
HEATER
CONNECTOR
PIVOT
WASHER
HOOKS
Main Menu
Table of Contents
4-way power adjustable (with seat heater):
for the seat wire harness installation.
HEADREST
BACK COVER
HOOKS
SEAT-BACK
HOOK
POWER SEAT
SWITCH
POWER SEAT
HARNESS
Installation is the reverse of the removal procedure.
CLIP
To seat cushion
cover.
NOTE:
Make sure the bushing and pivot washer are installed properly.
To prevent wrinkles when installing the seat-back cover, make sure the material is stretched evenly over the pad.
Grease the sliding portion.
SEAT-BACK
HEATER
CONNECTOR
SEAT CUSHION
CLIPS
PIVOT NUT
8 x 1.25 mm
22 N-m (2.2 kgf-m,
16 Ibf-ft)
SEAT HEATER
CONNECTOR
PIVOT
WASHER
SIDE AIRBAG
CONNECTOR
('99 - 01 models)
OPDS UNIT
CONNECTOR
('99 - 01 models)
BUSHING
CLIP
To seat cushion
cover.
10 x 1.25 mm
47 N-m (4.8 kgf-m,
35 Ibf-ft)
RECLINE
COVER
KNOBS
CAP
RECLINE
ADJUSTER
COVER
10 x 1.25 mm
47 N-m (4.8 kgf-m,
35 Ibf-ft)
CENTER
COVER
Disassembly
Main Menu
Table of Contents
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст